a fan draws 1.42m3 per second of air at a static pressure of 2.54 cm of water through a duct 300 mm diameter and discharges it through a duct of 275 mm diameter. Determine the static fan efficiency if total fan is 75% and air is measured at 25 degree celsius and 760 mm Hg

a fan draws 1.42m3 per second of air at a static pressure of 2.54 cm of water through a duct 300 mm diameter and discharges it through a duct of 275 mm diameter. Determine the static fan efficiency if total fan is 75% and air is measured at 25 degree celsius and 760 mm Hg

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.33P

See similar textbooks

Related questions

Q: A pipe carrying oil of specific gravity 0.877 changes in size from 150 mm at section 1 and 450 mm at…

A: Given data Specific gravity(SG) = 0.877 Diameter at section 1 = 150 mm Diameter at section 2 = 450…

Q: Q1/Water at 20'C is being pumped from a storage tank to an elevated second tank at a rate of 0.5…

A: Given data as per question volume flow rate =0.5 m3/s Elevation of the surface of storage tank =110…

Q: The pump whose characteristics are: H, = 80 – 600V2 %D n = -1500V² + 700V Elevation = 230 m (2) (1)…

A: Given- L = 1000 m d = 40 cm = 0.4 m

Q: 4. The impeller of a centrifugal blower has a radius of 18 cm and a blade width of 6.1 cm at the…

Q: Q2) What is the maximum flow rate through the pipe shown in blow if the elevation difference of the…

A: When any fluid having velocity V passes through a pipe of area A, then discharge through the pipe is…

Q: A centrifugal pump is required to pump water to an open water tank situated 4 km away from the…

Q: Water is delivered through a horizontal 20-cm-diameter pipe at a flow rate of 0.5 m3/s. If a…

A: Answer: The pitot probe positioned downstream of the manometer would indicate a pressure of 176.65…

Q: In a hydroelectric power plant, 100 m3/s of water flows from an elevation of 120 m to a turbine,…

A: Given data: *The volume flow rate of the water is V=100 m3/s. *The elevation of the flow of water to…

Q: What power can be delivered by the turbine if its efficiency is 100%? The water flow rate is 0.01…

A: Q=0.01m3/shL=13.0 mρ=1000kg/m3μ=0.001kg/m.s

Q: eter is A petroleum product is pumped at a rate of 2.32 x 10'm/s from a reservoir under atniospheric…

A: Given: The flow rate, Q = 2.32 x 10-3 m^3/s The height to be pumped, hd = 177 cm = 1.77 m The pump…

Q: water flows through a horizontal venturyi meter whose inlet diameter is 33 cm. and throat diameter…

Q: A pressurized tank of water has a 10-cm-diameter orifice at the bottom, where water discharges to…

Q: A horizontal Venturimeter with inlet and throat diameters 300 mm and 150 mm respectively is used to…

Q: Water from a reservoir is pumped over a hill through a 450 mm diameter and an absolute pressure of…

A: Note: As per our guidelines we are supposed to answer only the first 3 sub-parts. Kindly repost…

Q: 1. Water flows through a venturi meter. At the constricted section where the area is 24cm², the…

A: Given data:-Area at section 2-2, a2=24cm2=0.0024m2Pressure at section 2-2,…

Q: At the bottom of a pressurized water tank is a mouth with a diameter of 5 cm, where water is…

A: Fluid is a state of matter which deforms continuously on the application of force externally,…

Q: Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The…

A: Water temperature, T=65oCWater vapour pressure at 65oC, Pv=2.503 kPaWater density at 65oC, ρ=980.5…

Q: Q1/Water at 20°C is being pumped from a storage tank to an elevated second tank at a rate of 0.5…

A: Given data as Volume flow rate (Q)= 0.5 m3/s Elevation of storage tank = 110 m Elevation of second…

Q: 2. In a pumping system handling water, the level in the suction tank is 3m below the pump shaft…

Q: Water from a reservoir is pumped over a hill through a 450 mm diameter and an absolute pressure of…

Q: A hydraulic ram pump lifts 0.005 m3/s of water to a tank 20 m above the ram through a 80 m long and…

A: Given data: The height of the supply tank from ram h = 3 mThe length of the delivery pipe is L = 80…

Q: Determine the static fan efficiency if total fan mechanical efficiency is 70% and air is measured at…

A: Given DataQ=1.42m3/sηm=70%d2=275mmhw=2.54cmd1=300m

Q: A Venturimeter is inserted in a 150mm diameter pipe carrying an oil of specific gravity 0.85. If the…

Q: Water enters a hydraulic turbine through a 30-cmdiameter pipe at a rate of 0.6 m3/s and exits…

Q: At a water treatment plant, water (68°F) flows from tank 1 to tank 2 at a rate of 0.60 cfs through a…

A: Note:- From Colebrook equation(Turbulent flow):-…

Q: A fan draws 1.42 m³ per second of air at a static pressure of 2.54 cm of water through a duct 300 mm…

A: The stepwise procedure to solve this problem is shown in the following attached image:

Q: . A pressurized tank discharges to the atmosphere. Determine the initial discharge rate. 450 kPa h=…

Q: (3) In the figure below, the pipe entrance is sharp-edged. Consider the flow rate Q to be 0.004…

Q: An orifice with a 1.8-in-diameter opening is used to measure the mass flow rate of water at 60°F (?…

A: B =d/D B= 1.8/4 = 0.45

Q: A pump is 2.2 m above the water level in the sump and has a pressure of –20 cm of mercury at the…

A: Bernoulli's equation in terms of head is used to get the velocity at pump. Using continuity ,…

Q: A centrifugal pump is required to pump water to an open water tank situated 4 km away from the…

Q: For the same velocity, the entrance loss is of exit loss in the constant diameter pipe O 0.5 times O…

Q: The pump whose characteristics are: H, = 80 – 6o0v² n = -1500V² + 700V Elevation = 230 m |(2) (1)…

A: Given- d = 40 cm = 0.4 m L = 1000 m

Q: A pressurized tank of water has a 10-cm-diameter orifice at the bottom, where water discharges to…

A: In order to proceed with the given problem, the following assumptions need to be taken into…

Q: Electric power is generated in the hydroelectric power plant with a turbine-generator system, which…

Q: A 20 hp pump with a suction from an open reservoir (10 m above the pump) has a flow rate of 125…

Q: A centrifugal pump is required to deliver 50 liters of water per second to a height or 30 m through…

A: Discharge, Q= 50 liters of water per second= 0.050 m3/s Height, h= 30 m Length of the pipe, L= 100 m…

Q: A fan delivers 283.2 m³ / min of air with a density of 1.2 kg/m³ through a duct 5.08 cm by 5.08 cm…

A: (a) To find : The air velocity. Given data : The flow rate of air Q=283.2 m3min1 min60 sec=4.72 m3s.…

Q: Q#4: A pressurized tank of water has a 10-cm-diameter orifice at the bottom, where water discharges…

A: Consider the diagram shown below for the given tank. The velocity of water at the free surface…

Q: A horizontal pipe has an abrupt expansion from D1 = 8 cm to D2 = 16 cm. The water velocity in the…

A: Diameter of the inlet pipe D1 = 8 cm = 0.08m Diameter of the outlet pipe D2 = 16 cm = 0.16m Velocity…

Q: Q3. Water enters a tank of diameter DT steadily at a mass flow rate of min. An orifice at the bottom…

A: Drawing the figure as shown below - In sections 1 & 2 the tank is open to atmosphere and…

Q: A pressurized tank of water has a 10 cm diameter orifice at the bottom, where water discharges to…

Q: Water enters a tank of diameter D7 steadily at a mass flow rate of m: An orifice at the bottom with…

Q: What is the minimum power required from the pump to deliver the oil from Reservoir A to Reservoir B…

A: Given data as per the question Flow rate =0.3 m3/s Efficiency rating =70% Length of pipe =200 m…

Q: fan delivers 283.2 m³/min of air with a density of 1.2 kg/m³ through a duct 5.08 cm 08 cm at the…

Q: A Liquid fluid with a density of 1,750 kg/m3 from an elevated 2m open reservoir (P1=0 bars) flows…

A: If we want to calculate the power of pump then we just need 2 parameters. One is efficiency and…

Q: A pump is 2.2 m above the water level in the sump and has a pressure of –20 cm of mercury at the…

Q: Water is being pumped from a large lake to a reservoir 25 m above at a rate of 25 L/s by a 10-kW…

A: Given Gross head, HG = 25 m Head loss, h = 5 m Net head, H = 25 - 5 = 20 m…

Concept explainers

Hydronics

Question

a fan draws 1.42m³ per second of air at a static pressure of 2.54 cm of water through a duct 300 mm diameter and discharges it through a duct of 275 mm diameter. Determine the static fan efficiency if total fan is 75% and air is measured at 25 degree celsius and 760 mm Hg

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps with 11 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A fan draws 2.42 m^3 per second of air at a static pressure of 2.54 cm water through a duct 300 mm diameter and discharges it through a duct of 275 mm diameter. Determine the static fan efficiency IN PERCENT if total fan mechanical is 75 percent and air is measured at 25 deg. Celsius and 760 mm Hg.
A fan draws 1.42 m3 per second of air at a static pressure of 2.54 cm of water through a duct 300 mm diameter and discharges it through a duct of 275 mm diameter. Determine the static fan efficiency if total fan mechanical is 70% and air is measured at 25 0C and 760 mmHg. Using p water formulaPw=
A centrifugal pump is required to deliver 50 liters of water per second to a height or 30 m through a 100 m long pipe of 15 cm diameter. The inlet losses in the suction pipe are estimated to be 0.35 m. Assuming an overall efficiency of 70 percent and taking Darcy’s friction coefficient of 0.015 for the pipeline, determine the power, in kW, required to drive the pump.
Determine the static fan efficiency if total fan mechanical efficiency is 70% and air is measured at 25 deg C and 760 mmHg for a fan that draws 1.42 cubic meters of air per second at a static pressure of 2.54 cm of water through a duct 300 mm diameter and discharges it through a duct of 275 mm diameter.
14A fluid flows at a speed of 7.5 m/s in a pipe with a diameter of 35 cm. What is the power, in W, of the pump to overcome the irreversible pressure drop when the pressure drop along the pipe is calculated to be 6300 Pa?
Given parameters D1=30 cm L1=300 m D2=20 cm L2=150 m D3=25 cm L3=200 m f1=0.018, f2=0.02, and f3=0.019, determine the flow rate between reservoirs A and B, which are connected to each other as shown in the diagram. Note that the sudden contraction loss coefficient k is assumed to be 0.24.
A pressurized tank of water has a 10-cm-diameter orifice at the bottom, where water discharges to the atmosphere. The water level is 3 m above the outlet. The tank air pressure above the water level is 300 kPa (absolute) while the atmospheric pressure is 100 kPa. Neglecting frictional effects, determine the initial discharge rate of water from the tank
Toluene at 35 degrees Celsius is pumped from an open reservoir to a tank kept at a gauge pressure of 150 kPa. The pump itself is 3m below the reservoir, while the discharge tank is 10m above the reservoir. Assuming friction in the suction line is negligible, while in the discharge line the friction head amounts to 7.5 m, determine the net positive suction head available for the pump. If the pump has an efficiency of 65%, determine the total power input. At the given temperature, the density and vapor pressure of toluene are 862 kg/m3 and 40 mmHg
A fan running at 1480 rpm takes in 6 m^3/min of air at inlet conditions of P_1=950 mbar and T_1=15^0 C. If the fan impeller dimeter is 40 cm and the table tip air angle 20^0, determine the total pressure developed by the fan and the impeller width at exit. Take the radial velocity at the exit as 0.2 times the impeller tip speed. State the assumptions used.
At the bottom of a pressurized water tank is a mouth with a diameter of 5 cm, where water is discharged into the atmosphere. The water level is 2 m above the outlet. The tank air pressure above the water level is 300 kPa (absolute) and the atmospheric pressure is 100 KPA. Determine the initial rate of water discharge (volumetric flow rate) from the tank, neglecting the effects of friction.
Water at four-degree Celsius flows through a pipe that has a conical shape and is sloping downward; has a height difference of 20 meters. The cross section at the bottom is one-half that at the top. If the speed and pressure of water at the top are 1 m/s and 3x105 Pa, what is the pressure at the bottom (20 meters below the top)?
A fluid enters a pipe at speed v1=0.1 m/s. the diameter of the tube is d=200mm and the fluid flowing through the pipe is mercury with a specific gravity of 13.6. the mass flow rate is