The wheel is made from a 5-kg thin ring and two 2-kg slenderrods. If the torsional spring attached to the wheel's center hasa stiffness k = 2 N •m/rad, so that the torque on the centerof the wheel is M = (20) N • m, where 'e is in radians,determine the maximum angular velocity of the wheel if it isrotated two revolutions and then released from rest.HINT: USET, + XU1-2 = T;0,5 mw for the wheel is3.2 rad/sec14.1 rad/sec18.1 rad/sec6.04 rad/sec1.58 rad/sec34

According to the given information, we have the mass of the wheel is 5kg thin ring and 2 kg slender…

The wheel is made from a 5-kg thin ring and two 2-kg slender rods. If the torsional spring attached to the wheel's center has a stiffness k = 2N- m/rad, so that the torque on the center of the wheel is M = (28) N - m, where 'e is in radians, determine the maximum angular velocity of the wheel if it is rotated two revolutions and then released from rest. HINT: USE T + EU1-3 = T; 0,5 m - for the wheel is 3.2 rad/sec 14.1 rad/sec 18.1 rad/sec 6.04 rad/sec 1.58 rad/sec

The wheel is made from a 5-kg thin ring and two 2-kg slender rods. If the torsional spring attached to the wheel's center has a stiffness k = 2N- m/rad, so that the torque on the center of the wheel is M = (28) N - m, where 'e is in radians, determine the maximum angular velocity of the wheel if it is rotated two revolutions and then released from rest. HINT: USE T + EU1-3 = T; 0,5 m - for the wheel is 3.2 rad/sec 14.1 rad/sec 18.1 rad/sec 6.04 rad/sec 1.58 rad/sec

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The body and bucket of a skid steer loader has a weight of 2000 lb, and its center of gravity is located at G. Each of the four wheels has a weight of 100 lb and a radius of gyration about its center of gravity of 1ft. If the engine supplies a torque of M = 100 lb ft to each of the rear drive wheels, determine the speed of the loader in t = 10 s starting from rest. The wheels roll without slipping
The 153-kg wheel has a radius of gyration about its center of mass O of kO = 283 mm. If it rotates counterclockwise at an angular speed of 1431 rev/min and the tension force applied to the braking band at A is TA = 1771N,a) Determine the angular acceleration, in rad/s2, so that the wheel comes to rest in 67.6 revolutions after TA and TB are applied.
The 10-kg uniform slender rod is suspended at rest when the force of F = 150 N is applied to its end. Determine the angular velocity of the rod when it has rotated 180° clockwise from the position shown. The force is always perpendicular to the rod.
The system is at rest with the sprng unstretched when theta = 0. The 5.3 kg uniform slender bar is then given a slight clockwise nudge. The value of b is 0.45 m. If the bar comes to momentary rest when theta = 58, determine the spring constat k. For the value k = 65N/m, find the magnitude of the angular velocity of the bar when theta = 38
The 75 kg wheel has a radius of gyration about its mass centreof kG=400mm. If it is subjected to a torque of M=150 N.m,determine:a. The angular acceleration of the wheel,b. The linear acceleration of the mass centrec. The created frictional force at the point of contact.The coefficient of static friction between the wheel and theground is S=0.3.Hint: Assume no slipping occurs at star, and verify I at the end.
The 31-kg reel is mounted on the 16-kg cart. Part A: If the cable wrapped around the inner hub of the reel is subjected to a force of P=50N, determine the velocity of the cart when t = 4.2 s. The radius of gyration of the reel about its center of mass O is kO=250mm. Neglect the size of the small wheels. Part B: Determine the angular velocity of the reel when t = 4.2 s.
Gears A and B each have a mass of 2.4 kg and a radius of gyration of 60 mm, while gear C has a mass of 12 kg and a radius of gyration of 150 mm. A torque M with constant magnitude of 10 N.m to gear C. Determine a) the number of revolutions of gear C that is required for its angular velocity to increase from 100 to 450 rpm. b) the corresponding tangential force acting on gear A Please include the free body diagram if necessary.
The assembly consists of two 15 lb bars and a 25 lb disc. If the spring is without deformation when theta= 45 ° if the assembly is released from rest in this position, determine the angular velocity of the bar ?? when theta= 0 ° is reached. The disc rolls without slipping.
The thin 12 kg bar has an angular velocity in a clockwise direction ω = 1.5 rad/s when in position shown. Determine its angular acceleration and the normal reactions of the smooth surface A and B at that time. i = (1/12) M . L² for a homogeneous thin bar of mass M and length L.
The 13.5-lblb disk rests on the 5-lblb plate. A cord is wrapped around the periphery of the disk and attached to the wall at BB. A torque MM = 40 lb⋅ftlb⋅ft is applied to the disk. Assume the disk does not slip on the plate and the plate rests on the surface at DD having a coefficient of kinetic friction of μkμk = 0.2. Neglect the mass of the Determine the angular acceleration of the disk measured counterclockwise . Determine the time needed for the end CC of the plate to travel 3 ftft and strike the wall.
If the cord is subjected to a horizontal force of P = 150 N, and gear is supported by a fixed pin at O,determine the angular velocity of the gear and the velocity of the 20-kg gear rack in 4 s, starting from rest. The mass of the gear is 50 kg and it has a radius of gyration of k0 = 125 mm. Assume that the contact surface between the gear rack and the horizontal plane is smooth.
At the instant shown, the 200-lb bar rotates clockwise at 4 rad/s. The spring attached to its endalways remains vertical due to the roller guide at C. If the spring has an unstretched length of 2ft and a stiffness of k = 9 lb/ft, determine the angular velocity of the bar the instant it has rotated 39° clockwise.