A 4-kg disk A is mounted on arm BC, which has anegligible mass. If a torque of M = (5e0.51) N• m, where t isin seconds, is applied to the arm at C, determine the angularvelocity of BC in 2 s starting from rest. Solve the problemassuming that (a) the disk is set in a smooth bearing at B sothat it moves with curvilinear translation, (b) the disk isfixed to the shaft BC, and (c) the disk is given an initialfreely spinning angular velocity of w, = {-80k} rad/s priorto application of the torque.250 mmB60 mmM = (5e5) N - m

a)When the disk is set in smooth bearing at B so that it moves with curvilinear translation…

Answered: A 4-kg disk A is mounted on arm BC,…

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.11P: Solve Prob. 7.10 assuming that the pick-up truck has front-wheel drive.

See similar textbooks

Similar questions

The wheel has a mass of 100 kg and a radius of gyration of kO = 0.2 m. A motor supplies a torque M = (40u + 900) N #m, where u is in radians, about the drive shaft at O. Determine the speed of the loading car, which has a mass of 300 kg, after it travels s = 4 m. Initially the car is at rest when s = 0 and u = 0°. Neglect the mass of the attached cable and the mass of the car’s wheels
If the cord is subjected to a horizontal force of P = 150 N, and gear is supported by a fixed pin at O,determine the angular velocity of the gear and the velocity of the 20-kg gear rack in 4 s, starting from rest. The mass of the gear is 50 kg and it has a radius of gyration of k0 = 125 mm. Assume that the contact surface between the gear rack and the horizontal plane is smooth.
The rod AB has a mass of 20 kg，the mass of the piston A and B are both 5kg. Piston B is attached to a spring of constant k = 1200 N/m. The spring is un-stretched when θ = 0. If the rod is released from rest whenθ = 45° Please find÷ (1) the moment inertia of the rod AB about its mass center G (2)The angular velocity of rod AB at θ = 0° (3）the velocity of piston A at θ = 0° (4) the velocity of Piston B at θ = 0° (hint: regard the piston A, B, rod as a system, during the motion, except the spring, the weight of rod AB, the weight of pistonB also does work). g = 9.8 m/s2
The pendulum has a mass of 8.8 kg, a centre of gravity at G, and a radius of gyration of 0.31 m about the fixed pin support at O. At what position (in degrees) must the pendulum by released from rest so that its angular acceleration is 18.6 (clockwise) at that instant? Take = 0.25 m. The motion occurs in a vertical plane and friction is negligible. Choose the correct answer. 43.2 36.7 34.6 48.4 41.1
Prove the relation that Hammer blow = ± mb x r*x ω2 where mb = Balancing mass placed at a radius of r* and ω= angular speed of the crank.
A railroad car that is assumed to be rigid and has a mass of 80 Mg ismoving forward at a speed of v = 0.2 m>s when it strikes a steel 200 mmby 200 mm post at A, Fig. a. If the post is fixed to the ground at C,determine the maximum horizontal displacement of its top B due to theimpact. Take Est = 200 GPa.
Consider a slender rod AB with a length l and a mass m. The ends are connected to blocks of negligible mass sliding along horizontal and vertical tracks. If the rod is released with no initial velocity from a horizontal position as shown in Fig.A, determine its angular velocity after it has rotated through an angle of θ (see Fig B) using the conservation of energy method. (Hint: Moment of inertia of rod about G = (1/12)ml2 The kinetic energy of a rigid body in plane motion is
The 153-kg wheel has a radius of gyration about its center of mass O of kO = 283 mm. If it rotates counterclockwise at an angular speed of 1431 rev/min and the tension force applied to the braking band at A is TA = 1771N,a) Determine the angular acceleration, in rad/s2, so that the wheel comes to rest in 67.6 revolutions after TA and TB are applied.
Solve Prob. 7.10 assuming that the pick-up truck has front-wheel drive.
The 13.5-lblb disk rests on the 5-lblb plate. A cord is wrapped around the periphery of the disk and attached to the wall at BB. A torque MM = 40 lb⋅ftlb⋅ft is applied to the disk. Assume the disk does not slip on the plate and the plate rests on the surface at DD having a coefficient of kinetic friction of μk = 0.2. Neglect the mass of the cord Determine the angular acceleration of the disk measured counterclockwise . Determine the time needed for the end CC of the plate to travel 3 ftft and strike the wall.
The two gears A and B have weights and radii of gyration of WA = 15 lb , kA = 0.5 ft and WB = 15 lb , kB = 0.35 ft, respectively. A motor transmits a couple moment to gear B of M=2(1−e−0.5t)lb⋅ft, where t is in seconds. Determine the angular velocity of gear A in t = 5 s , measured counterclockwise, starting from rest.
A motorcycle and rider have a combined mass of 350kg. The each wheel has a mass of 20kg with the diameter of 500 mm. The rider accelerates from 5m/s to 25m/s over a distance of 100m, whilst climbing a hill of slope 1 in 20. Identify the magnitude and effect of gyroscopic reaction torque by calculating the angular velocity and power as the motorcycle ascends the incline when the motorcycle and rider travel at 80 km/h around a left-hand bend of road with the radius 30 m.Explain the effects of energy transfer in mechanical systems (e.g. gears, pulley or flywheel) with uniform acceleration present.

SEE MORE QUESTIONS

Recommended textbooks for you

International Edition---engineering Mechanics: St…

Mechanical Engineering

ISBN:

9781305501607

Author:

Andrew Pytel And Jaan Kiusalaas

Publisher:

CENGAGE L