The width of the rectangular gate of AB (Figure 5), which is hinged from the point of A, is 4m.It is known that the weight of the gate is 1810 kN. What is the maximum allowable depth (h) of the water on the left side of the chamber to keep the gate in stable position?

The width of the rectangular gate of AB (Figure 5), which is hinged from the point of A, is 4m.It is known that the weight of the gate is 1810 kN. What is the maximum allowable depth (h) of the water on the left side of the chamber to keep the gate in stable position?

Name: The width of the rectangular gate of AB (Figure 5), which ishinged fr
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: The width of the rectangular gate of AB (Figure 5), which ishinged from the point of A, is 4m.lt is known that the weight ofthe gate is 1810 kN. What is the maximum allowable depthBall joint4 mWater Amax2 m(h) of the water on the left side of the ch

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

One side of the container has a 03-m square door that is hinged at its top edge. If the container is filled with water, determine the smallest force F that must be applied to the bottom edge of the door to keep it closed.
The gate AB shown in the figure is is 3 ft high and 6 ftwide. The gate is hinged at A and restrained by astop at B. If the depth of the water is 20 ft, calculate thereactions at A and at B.?? = _______________ ?? ?? = _______________ ?b
The gate shown is 3.0 m wide (into the page), hinges around the bottom point, and for the purposes of this analysis can be considered massless. A weight is attached to the top point, and is threaded through a frictionless pulley. For what depth of water (d) will this rectangular gate be in equilibrium at an angle of 60o as shown?
6-m-wide rectangular gate shown is hinged at B and leans against the floor at A making an angle of 45° with the horizontal The gate is to be opened from its lower edge by applying a normal force at its center. Determine the minimum force F required to open the water gate.
A triangular gate having horizontal base of 1.0m and an altitude of 1.5m is inclined 45° from the vertical with the vertex pointing upward. The vertex of the gate is 2.4m vertically below the surface of the water. What normal force , in KN, must be applied at the vertex of the gate to open it's hinged at the base?
A long solid cylinder of radius 0.8 m hinged at point A is used as an automatic gate, When the water level reaches 5 m, the gate opens by turning about the hinge at point A. Determine (a) the hydrostatic force acting on the cylinder and its line of action when the gate opens and (b) the weight of the cylinder per m length of the cylinder.
The vertical side of reservoir has a rectangular opening 2.75 m long and 1.2 m high. It is closed by a plate using 4 bolts placed at the corners of the opening. What would be the tension in the bolts if water stands to height of 1.8 m above the top edge of the opening which horizontal ?
A cubical box, 1.5 m on each side, has its base horizontal and is half-filled with water. The remaining is filled with air under a gage pressure of 82 kPa. One of the vertical sides is hinged at the top and is free to swing inward. To what depth can the top of the box be submerged in an open body of fresh water without allowing any water to enter?
A triangular wooden body (S=0.80) is placed in water in theposition indicated in the figure. If the width of the body is 7.0 m,determine if the same for this position is stable or not indicating themetacentric height (YM).
A semicircular gate with a diameter of 6 ft is installed at 50º as shown below. The top of the gate is 5 ft below the water surface. Determine the resulting hydrostatic force and the location of the center of pressure on the gate.
EMERGENCY!!!! The cover in the figure is hinged at the center O and has a fixed width w = 5 m. The equation of the surface is x = y2 / a (a = 3 m), the depth of the water to the right of the lid (D = 4 m). If the weight of the lid is neglected, it is necessary to keep the lid in balance. Find the size of the force (Fa) required, as shown. Take the density of the water as 999 kg / m3.
An elliptical plate, major axis 6 feet and minor axis 4 feet, is submerged vertically until its minor axis lies in the surface of the water (weight density =p Ib/fr3). Determine the appropriate integral to be used to determine the force on one side of the submerged