The z-y coordinate system is body fixed with respect to the bar. The angle 0 (in radians) is given as a function of time by 0 = 0.1 +0.08t2. The a coordinate of the sleeve A (in feet) is given as a function of time by z = 3+0.06t°. Determine the velocity of the sleeve at t = 4 s relative to a nonrotating reference frame with its origin at B. (Although you are determining the velocity of A relative to a nonrotating reference frame, your answer will be expressed in components in terms of the body-fixed reference frame.)

The z-y coordinate system is body fixed with respect to the bar. The angle 0 (in radians) is given as a function of time by 0 = 0.1 +0.08t2. The a coordinate of the sleeve A (in feet) is given as a function of time by z = 3+0.06t°. Determine the velocity of the sleeve at t = 4 s relative to a nonrotating reference frame with its origin at B. (Although you are determining the velocity of A relative to a nonrotating reference frame, your answer will be expressed in components in terms of the body-fixed reference frame.)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A rigid bar is moving along two perpendicular walls. The length of the bar is LAB=1.0m. At an instant, velocity at point A is VA=1.0 m/s downward. The angle between the bar and the vertical wall is θ=30°. (1) Determine the IC (instantaneous center of zero velocity) center________ A. Point B B. Point C C. Point G D. Point O
The rigid body is rotating about the y-axis. In the position shown in Fig. (a), the angular velocity and angular acceleration of the body are as specified in the figure. Determine the velocity and acceleration vectors of point A in this position using(1) vector equations; and (2) scalar equations. Ans:VA= 0.3im/sBA = -0.9k - 0.2i m/s2
The figure shows a right-angled construction frame ABC. When measured at rest, it has dimensions as follows: AB = 18.9 m, AC = 10.0 m, and BC = 16.0 m. This frame is now given a new velocity of 0.420 c, relative to Earth, in a direction parallel to AC. How long is part BC of this frame with the new velocity as measured by Earth-based engineers?
Assuming there is no slippage for the belt assembly below, Determine the following: (a) What is the angular velocity of each pulley if the belt has a constant speed of 5 m/s? What is the frequency and the period of each pulley? (b) What is the average angular velocity of each pulley if the rope accelerates from 5 m/s to 10 m/s in 10 s? How many revolutions does the pulley turn in that time? R 1 = 0.3 mR 2 = 0.2 mR 3 = 0.1 m
Point A on the rod has a velocity of 8 m/s to the right. Where is the IC for the rod? At what point?
The constant angular acceleration of the rotating disk is 12 rad/s . The angular velocity of the disk is 24 rad/s clockwise when t = 0. Determine the total angle turned by the disk between t = 0 and t = 4sec. the answer is 48 rad. show your solution.
A body rotates according to the relation a=2t; where a is in rad/sec^2 and t is in sec. W =4 rad/sec and theta is zero when t is zero compute the values at w and theta at the instant when t=2 sec
Example] The two ends of bar AB slides along the vertical and horizontal surfaces. MA = 1,, MB = 1,0 = ot(@= const.) Determine the motion equation, the magnitude of the velocity and acceleration for point M. B
The flexible band F is connected in E to the rotating sector and has a constant speed of 4 m/s, as shown. Find:a) The angular velocity BD at the instant BD is perpendicular to OA. b) The angular acceleration BD at the instant BD is perpendicular to OA.
In the system shown in the figure, rod ab rotates at 5rad / s speed. When theta angle is 60 degrees, determine the velocity of block c.
The power of an engine running at 125 rpm is turned off and the engine comes to rest at the end of 2 min and 40 sec. Assuming that there is no slipping between the belt and pulley surface and that the deceleration is uniform, find 1) the average speed in radians per second of the engine pulley in coming to rest; 2) the total angular distance traveled in revolutions, radians and degrees in coming to rest; 3) the distance in feet traveled by a belt running on the pulley in coming to rest, if the pulley diameter is 3ft.
A load is raised 11 ft by the gears and wheel system below. Gear A is initially rotating at rest and accelerates uniformly to omega = 24 rpm in t= 10 sec and maintain then maintain this constant 24 rpm speed. The dimensions are rA= 1 in, rB= 9 in and rC=16 in. 2) After 10 sec, find the distance s2 in feet and in NC es needed to reach the 11 ft, find thetaC2(t), alphaA2, alphaB2 in rad/s^2, omegaA2(t), omegaB2(t) in rad/s, thetaA2(t), in rad and the distance s2 in ft that should be made to get to the 11 ft raising distance of the load. 3) Deduce the number of revolutions made by gear A and how long it will take, to raise the load up to 11 ft.