There is 100 grams of water in a brass calorimeter of mass 200 grams. It is found that 590 calories are required to raise the temperature of water and container from 20°C to 25°C. What is the specific heat of the brass?

There is 100 grams of water in a brass calorimeter of mass 200 grams. It is found that 590 calories are required to raise the temperature of water and container from 20°C to 25°C. What is the specific heat of the brass?

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.21P

See similar textbooks

Related questions

Q: Problem 204. In an 11.2 dm high cylindrical container, whose base area is 1 dm², a frictionless…

Q: 1- The steady state temperature profile for a wire carrying current is R* (1- G) gR T(4) = + + T; %|…

Q: insulator has a thermal conductivity of 20 W/m ºC s used to separate two heat sinks whose…

Q: 2. The cabin air in an empty aircraft on the ground in a tropical country is maintained at a…

A: Given : Ta=35 CTc=21 Cha=39 W/mKhc=9 W/mK To find : Power

Q: Heat is conducted through a slab composed of parallel layers of different conductivities, 0.0050 and…

Q: Heat Transfer Mechanisms 5- In a certain experiment, cylindrical samples of diameter 4 cm and length…

Q: the temperature is low compared to a summer night, an engineering student, studying Heat Transfer…

A: This question is belongs to Thermodynamics, heat transfer.

Q: A heat conducting rod, 0.30 m long, is made of an aluminum section that is 0.10 m long, and a copper…

A: A heat conducting rod, 0.30 m long, is made of an aluminum section that is 0.10 m long, and a copper…

Q: A 1.0-kW heater is constructed of a glass plate with an electrically conducting film that produces a…

Q: A plane wall 7.5 cm thick(k=21W/mK) generates heat internally at the rate of 0.35 MW/m³. One side of…

Q: A new 1 ft thick insulating material was recently tested for heat resistant properties. The data…

A: Given Data⇒ Temperature recorded on the cold side Tc=700F Temperature recorded on the hot side…

Q: Newton's Law of cooling: (3.1 p. 88) A cake is removed from an oven and its temperature is 300°F.…

A: The initial temperature of the cake when it is removed from the oven θ1=300oFafter three minutes its…

Q: 80. A plate-type fuel element, having a thermal conductivity of 2 W/m-K, pro- duces heat. The heat…

A: The actual mechanism of heat transfer in any fin is first heat get conducted into the fin at its…

Q: Determine the amount of heat removed from 1.5 kg of bologna (sausage) when cooled from 24°C to -7°C.…

Q: 6 cm long copper rod (k = 300 W/mK) 6mm in diameter is exposed to an environment at 20°C. The base…

A: Given:L=6 cm =0.06 mK=300 W/m.Kd=6 mm =0.006 mT∞=20 deg CT=160 deg Ch=20 W/m2.K

Q: 3) Air at 20•C blows over a hot plate 50 by 75 cm maintained at 250•C. The convection heat- transfer…

A: Basics of Heat transfer are used.

Q: A glass vessel with an insulating cover with a surface area of (Z + 100) cm² and (Z + 15) mm thick…

A: given:temperature of ice=00Ctemperature of second vessels=1000clatent heat of ice=3.3×105j/kgk for…

Q: A well insulated piston-cylinder assembly contains one mole of ideal gas. There are two 3000 kg…

A: a) It is given that there are two blocks of 3000 kg each with insulated 0.04 m2. First of all,…

Q: nickel plate 0.8 cm thick has a temperature difference of 64°C between its faces. It transmits…

A: We have to solve the above question determine thermal conductivity of nickel in cgs units.

Q: Q7/ The maximum operating temperature of a kitchen oven is set at 310°C. Due to seasonal variations,…

Q: 1ai. a steel bar 10.0 cm long is welded end-to-end to a copper bar 20.0 cm long. Both bars are…

A: Since you have posted a multiple independent question in a single question We will solve first…

Q: A flat surface is covered with insulation with a thermal conductivity of 0.08 W/m · K. The…

A: Thermal conductivity of insulation,K=0.08WmKTemperature at interface,TS=300οC=(300+273)K=573KHeat…

Q: You are pouring a concrete pad 0.1 m thick. The curing of concrete is an exothermic chemical…

Q: Question 2 The composite wall of an oven consists of three materials, two of which are of known…

Q: Q2:- A sphere made of pure copper, which is 13 mm in diameter, is 70 °C (at t=0) when it inserted…

Q: The radius and the length of a cylindrical metal are 5.00 cm and 20.00 cm at 25°C, respectively.…

A: Given l=20.02 cm (del)T=85.25 degree C Q=9000 J

Q: b. A slab of stone of area (3600 + R) cm² and thickness 10 cm is exposed on the lower surface to…

A: Draw diagram of slab for better understanding

Q: What is the heat transfer rate of a single fin? b.Plot the temperature distribution within the fin…

Q: Calculate the total resistance (in K/W ) through the vertical walls of a boiler furnace 20 m in…

A: Resistance R =L/KA total R = R1 + R2 + R3 Q = delta T / total R

Q: Numerical Exercise 1. A flat plate is supplied with a constant heat flux of 100 [W/m²] from bottom.…

A: 1. A flat plate is supplied with a constant heat flux of 100 [W/m²] from bottom. The plate has 0.5m²…

Q: The crank shaft of the engine car consists of a bearing subjected to a friction could produce a…

A: Given Data Circular shaft diameter =5 cm Temperature rise ∆T=50° h=1 Wm2k k=55 Wm2k Let an element…

Q: heat. of 0.8 k

Q: How much joules are needed to change 100 grams of water at 10°C to steam at 120°C

Q: Find the thermal resistance r (in hr · °F/BTU) and the equivalent R-value (in hr · ft. °F/BTU) of a…

A: Given that, Wall dimension=18'×8'Inside temperature=72 °F,Outside temperature=32 °F,Thickness of…

Q: The inner and outer surfaces of a 5m x 10m brick wall of thickness 30 cm and thermal conductivity…

A: As per given question Determine the rate of heat transfer through the wall, in W. [Note: State all…

Q: heating cube with a size of 60 x 60 cm on the inside is made of refractory brick (k=1.04 watt/(m.°c)…

A: Given Data K=1.04 W/mK X=12 cm

Q: Two parts and label (A) & (B) Solve carefully! Question : The roof of a car in a parking lot absorbs…

Q: Consider a single cylindrical fin of a uniform cross-sectional area (D = 5 mm, L = 70 mm, k = 400…

Q: A resistor provide energy to a metal block 20 cm wide with a conductivity of 120 W/m.k. The…

Q: The front door of an oven is made up of walls made up of materials A, B and C, juxtaposed. The walls…

Q: Air is trapped in the piston in the cylinder. A spring is connected to the upper portion of the…

A: In this question, there is a constant force applied by the spring on the piston. Thus the resulting…

Q: 16. Calculate the number of solar thermal collectors of 2m2 area each, required to design a solar…

Q: In a nice Christmas evening, where the temperature is low compared to a summer night, an engineering…

A: A human body can be considered as a thermodynamic system because it continuously generates heat. As…

Q: THERMODYNAMICS A 1.5kW iron has a 0.5 cm thick brass base plate (p=8,310 kg/m3 and cp = 400 J/kg C)…

Q: In an experiment to find the thermal conductivity, a metallic rod of diameter 25 mm is placed in a…

Q: Water is to be heated from 20°C to 70°C as it flows through a 40 mm Inter diameter and 600 mm long…

Q: Heat Transfer A wall of an oven with a wire in it. Across the wire a voltage of 50 Volts and a…

Concept explainers

Conduction and Convection

When energy travels from one object to another it is said to have undergone heat transfer. Heat transfer is nothing but the transfer of thermal energy or internal energy from one thing to another, like e.g., when a vessel with water, kept on top of a burner, heats up because of the flame underneath it.

Question

COMPLETE FBD SOLUTION AND REQUIREMENTS

PS. THIS IS A HEAT TRANSFER PROBLEM

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

1.63 Liquid oxygen (LOX) for the space shuttle is stored at 90 K prior to launch in a spherical container 4 m in diameter. To reduce the loss of oxygen, the sphere is insulated with superinsulation developed at the U.S. National Institute of Standards and Technology's Cryogenic Division; the superinsulation has an effective thermal conductivity of 0.00012 W/m K. If the outside temperature is on the average and the LOX has a heat of vaporization of 213 J/g, calculate the thickness of insulation required to keep the LOX evaporation rate below 200 g/h.
One end of a 0.3-m-long steel rod is connected to a wall at 204C. The other end is connected to a wall that is maintained at 93C. Air is blown across the rod so that a heat transfer coefficient of 17W/m2 K is maintained over the entire surface. If the diameter of the rod is 5 cm and the temperature of the air is 38C, what is the net rate of heat loss to the air?
A 0.6-cm diameter mild steel rod at 38C is suddenly immersed in a liquid at 93C with hc=110W/m2K. Determine the time required for the rod to warm to 88C.
2.43 A turbine blade 6.3 cm long, with cross-sectional area and perimeter , is made of stainless steel . The temperature of the root, , is . The blade is exposed to a hot gas at , and the heat transfer coefficient is K. Determine the temperature of the blade tip and the rate of heat flow at the root of the blade. Assume that the tip is insulated.
The handle of a ladle used for pouring molten lead is 30 cm long. Originally the handle was made of 1.9cm1.25cm mild steel bar stock. To reduce the grip temperature, it is proposed to form the handle of tubing 0.15 cm thick to the same rectangular shape. If the average heat transfer coefficient over the handle surface is 14 W/m K, estimate the reduction of the temperature at the grip in air at 21C.
1.4 To measure thermal conductivity, two similar 1-cm-thick specimens are placed in the apparatus shown in the accompanying sketch. Electric current is supplied to the guard heater, and a wattmeter shows that the power dissipation is 10 W. Thermocouples attached to the warmer and to the cooler surfaces show temperatures of 322 and 300 K, respectively. Calculate the thermal conductivity of the material at the mean temperature in W/m K. Problem 1.4
A square silicon chip 7mm7mm in size and 0.5-mm thick is mounted on a plastic substrate as shown in the sketch below. The top surface of the chip is cooled by a synthetic liquid flowing over it. Electronic circuits on the bottom of the chip generate heat at a rate of 5 W that must be transferred through the chip. Estimate the steady-state temperature difference between the front and back surfaces of the chip. The thermal conductivity of silicon is 150 W/m K. Problem 1.6
2.2 A small dam, which is idealized by a large slab 1.2 m thick, is to be completely poured in a short Period of time. The hydration of the concrete results in the equivalent of a distributed source of constant strength of 100 W/m3. If both dam surfaces are at 16°C, determine the maximum temperature to which the concrete will be subjected, assuming steady-state conditions. The thermal conductivity of the wet concrete can be taken as 0.84 W/m K.
1.10 A heat flux meter at the outer (cold) wall of a concrete building indicates that the heat loss through a wall of 10-cm thickness is . If a thermocouple at the inner surface of the wall indicates a temperature of 22°C while another at the outer surface shows 6°C, calculate the thermal conductivity of the concrete and compare your result with the value in Appendix 2, Table 11.
A plane wall of thickness 2L has internal heat sources whose strength varies according to qG=qocos(ax) Where qo is the heat generated per unit volume at the center of the wall (x=0) and a is a constant. If both sides of the wall are maintained at a constant temperature of Tw, derive an expression for the total heat loss from the wall per unit surface area.
2.30 An electrical heater capable of generating 10,000 W is to be designed. The heating element is to be a stainless steel wire having an electrical resistivity of ohm-centimeter. The operating temperature of the stainless steel is to be no more than 1260°C. The heat transfer coefficient at the outer surface is expected to be no less than in a medium whose maximum temperature is 93°C. A transformer capable of delivering current at 9 and 12 V is available. Determine a suitable size for the wire, the current required, and discuss what effect a reduction in the heat transfer coefficient would have. (Hint: Demonstrate first that the temperature drop between the center and the surface of the wire is independent of the wire diameter, and determine its value.)
Water at a temperature of 77C is to be evaporated slowly in a vessel. The water is in a low-pressure container surrounded by steam as shown in the sketch below. The steam is condensing at 107C. The overall heat transfer coefficient between the water and the steam is 1100W/m2K. Calculate the surface area of the container that is required to evaporate water at a rate of 0.01 kg/s. Problem 1.16