Three alcohol bottles were mislabeled in the stockroom: 1-pentanol, 2-pentanol, and 3-pentanol. A clever student decided to using MS to determine the identity of the structures. Using the MS data, draw the structure of the compound found in each bottle. Bottle #1: Base peak with a m/z of 45 Bottle #2: Base peak with a m/z of 70 and two significant peaks with m/z of 42 and 31 Bottle #3: Base peak with a m/z of 59

Three alcohol bottles were mislabeled in the stockroom: 1-pentanol, 2-pentanol, and 3-pentanol. A clever student decided to using MS to determine the identity of the structures. Using the MS data, draw the structure of the compound found in each bottle. Bottle #1: Base peak with a m/z of 45 Bottle #2: Base peak with a m/z of 70 and two significant peaks with m/z of 42 and 31 Bottle #3: Base peak with a m/z of 59

Organic Chemistry: A Guided Inquiry

2nd Edition

ISBN:9780618974122

Author:Andrei Straumanis

Publisher:Andrei Straumanis

ChapterL4: Proton (1h) Nmr Spectroscopy

Section: Chapter Questions

Problem 4CTQ

See similar textbooks

Similar questions

A 0.1 g amine-containing compound is dissolved in water then diluted to 100 mL. To get the concentration of amine in this compound, you subject it to spectroscopic analysis. So, you get 1 mL of the previously diluted sample then dilute it again to 250 mL for measurement. Then, you fill 3/4 of a 1-cm cuvette with this diluted sample then you run an analysis using an AAS. The recorded absorbance is 0.545 at 410 nm. Solve for the molecular weight of the compound. The molar absorptivity is 1.23 x 104 cm-1 mol-1 L.
1. Is there a carbonyl in your unknown? State how you know. If one is present, state how the frequency narrows down the functional group it is a part of (carboxylic acid, ketone, aldehyde, ester, amide). 2. What functional groups are present in your unknown molecule? For each, correlate the functional group with the frequency of the identifying peak.
Arrange the following solvents in order of increasing polarity (least polar to most polar): Propyl Amine – Diethyl Ether – Ethyl Acetate- Octane If you ran an unknown sample on a TLC and observed only one spot with a Rf value of 0.95, is it safe to assume that it is a pure compound? If not, how can you check it out using TLC?
Consider a solution of 234mg of pentanol (FM 88.15) and 237mg of 2,3-dimethyl-2-butanol (FM 102.17) in 10.0mL where the two are separated with relative response pentantol:2,3-dimethyl-2-butanol = 0.913:1.00. Assume pentanol is the internal standard, find the relative response factor of 2,3-dimethyl-2-butanol. If the peak area for pentanol in a sample is 158 for 93.7mM and the area for 2,3-dimethyl-2-butanol is 164, what is the concentration of the 2,3-dimethyl-2-butanol?
This is a liquid unknown compound confirmed to be an alcohol. The IR, mass spec., H-NMR, and C-NMR are below. Analyzing the C-NMR what can be interpreted from the chemical shifts? What can be interpreted from the major peaks in the mass spectrum analysis? I know it’s an alcohol. There is a broad singlet at around 3.6-3.7 ppm, a triplet at 3.5 ppm, a nonet at around 1.8-1.9 ppm, a doublet at 0.9 ppm, and a quartet at around 1.4 ppm. With all this in mind what is this compound, specifically? And how would it be drawn out and relate to the H and C spectra?
How many carbon atoms are expected to be in a hydrocarbon sample if it shows M and M+1 peak intensities of 67.8 and 6.04 respectively? (round your answer to the nearest integer) a.9 carbons b.7 carbons c.6 carbons d.8 carbons
Here is the protocol for a UV-Vis spectrophotometer to detect water and chlorine-carbon. 1.Dissolve the water and chlorine-carbon compounds in a solvent, such as water. 2.Prepare a standard solution of known concentration that is similar to the sample being measured. 3.Calibrate the spectrophotometer using the standard solution. 4.Measure the absorbance of the sample using the spectrophotometer. 5.Calculate the concentration of the compounds in the sample using the calibration curve obtained from the standard solution. How is the spectrophotometer calibrated with standard solutions? When is the blank solution placed in the spectrophotmeter?
A 0.1 g amine-containing compound is dissolved in water then diluted to 100 mL. You subject it to spectroscopic analysis, in order to get the concentration of amine in this compound. Next, you get 1 mL of the previously diluted sample then dilute it again to 250 mL for measurement. Then, you fill 3/4 of a 1-cm cuvette with this diluted sample, and you run an analysis using an AAS. The recorded absorbance is 0.545 at 410 nm. What is the molecular weight of the compound? (The molar absorptivity is 1.23 x 104 cm-1 mol-1 L.)
Sample #1 has an absorbance of 0.300. Sample #2 is the same substance and has an absorbance of 0.600 using the same equipment. What is the relative concentration of the second sample? Select one: a. The concentration of sample #2 is the square root of that of #1. b. The concentration of sample #2 is that of sample #1 squared. c. The concentration of sample #2 is half that of sample #1. d. The concentration of sample #2 is twice that of sample #1.
Which of the following molecules matches the given data? (Note: All the molecules have a M+ = m/z 102) C5H10O2 base peak = m/z 43
How would you determine the concentration of BPA in an unknown sample if given this table and the unknown sample has a corrected peak area of 596985
After creating her standard curve for absorption versus the concentration (M) of FD&C Red 40, a student found that her best fit linear line for FD&C Red 40 was y = 2,962x + 0.005. Her Kool-Aid sample had an absorbance of 0.685. If 0.543 grams of Kool-Aid powder was used to prepare an 8-fl oz cup of her assigned flavor, what is the percent by mass of FD&C Red 40 in her 8-fl oz cup?