Please solve and show your detailed solutionNumber 27 Three capacitors having capacitance of 4 µF, 6 μF and 8 µF respectively areconnected in series. Find the equivalent capacitance of the combination.A. 1.08 μFB. 2.84 μFC. 1.85 µFD. 4.84 μF

Answered: Image /qna-images/answer/1df27c21-5605-4041-8426-0fc4ed7abc9c.jpg

Answered: Three capacitors having capacitance of…

Three capacitors having capacitance of 4 µF, 6 µF and 8 µF respectively are connected in series. Find the equivalent capacitance of the combination. A. 1.08 μF B. 2.84 μF C. 1.85 μF D. 4.84 μF

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter20: Capacitance In Ac Circuits

Section: Chapter Questions

Problem 5PP: Three capacitors having capacitance values of 20F,40F, and 50F are connected in parallel to a 60 -...

See similar textbooks

Related questions

Q: Of the three conductors, you used in this experiment (tubular resistor and two lamps) and based on…

A: Resistor tubes of a cemented (FU) or cemented design make up tubular resistors (FZ). The built…

Q: 5. Use source transformation to find the value of lo in the circuit. Μ 3 ΚΩ ww 36 ΚΩ 6 ΚΩ 34 ΚΩ 3 ΚΩ…

A: In this question, We need to determine the current Io using the source transformation. We are…

Q: A receiver is tuned to an RF signal of 96 MHz and the LO frequency is 100 104 MHz O 108 MHz 98 MHz…

A: Given data, RF signal frequency, fs=96 MHz. Local oscillator frequency, fl=100 MHz.

Q: BASIC ELECTRICAL ENGINEERING UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. NO…

A: Given length(l) = 5m Cross section (A) = 4x3 sq. cm = 4100×3100sq.m. = 32500 sq.m. Resistivity(ρ) :…

Q: A 50-ohm lossless transmission line has series inductance of 250 nH/m and shunt capacitance of 100…

Q: 4.5A (↑ 1₂ + V₁ M ≤6-2 12-2 +1 20V

Q: A current of 3.6 A transfers a charge of 375 mC. How long would this take?

A: It is given that: I=3.6A Q=375 mC

Q: 1. A. Hoover dam is located 275 miles from Los Angeles and it supplies 60 Hz power to the city. Can…

A: Given that: The circuit is shown below. Find: Write equations Ohm’s law and Kirchhoff's law.…

Q: Using Nodal analysis and following the given figure, write the equation at node B under this…

A: Given- Voltage source= VS1 and VS2 Resistances = R1 , R2 , R3 To find- Nodal equation at B =?

Q: For the transfer function G(s)H(s) = [1/s (s+1) (s+0.5)], What will be the phase cross-over…

A: Given- Transfer function- G(s) H(s) =1s(s+1)(s+0.5) , To find- Phase cross over frequency .

Q: "N|1| 52. Employ phasor analysis techniques to obtain expressions for the two mesh currents i and i2…

Q: Problem 7 Assume that the given circuit is at steady state before the switch opens at time t = 0.…

Q: Hello Sir. Good Evening. I have a question in my home work related Control System Lesson. The…

Q: B) For the lossless T.L shown below, the line is driven with a generator that has Eg=30Vrms and…

Q: A coil containing 50 turns rotates at a regular velocity inside a regular magnetic field Calculate:…

A: In this question we have given coil containing turns and rotating into magnetic field .....We have…

Q: 39A ww 3.2 type your answer... 13Ω www The circuit above is in DC steady state. What is the value of…

Q: Determine the total amount of power in the series circuit in Fig.

A: It is given that:

Q: 3. Write a Verilog module for the circuit below. j k m, mo 5.40 00 for IC of

A: main module: mux module:

Q: QUESTION FOUR 4. A 230V, 50 Hz transformer has 200 primary turns. It draws 5 A at 0.25 p.f lagging…

A: Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: 1- Which of the following analogue modulation scheme requires the minimum transmitted power and…

A: Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: Problem 8. For the oscilloscope display of a pulse waveform shown in Figure 10.18 the 'time/cm'…

A: Given: An oscilloscope display of a pulse waveform. The 'time/cm' switch is on 50 ms/cm The…

Q: O G .30 Is 60 40 5

Q: .what is the total resistance ? 2. What is the current and volt

Q: In the network shown in the figure, each of the resistance is equal to 20. The resistance between…

A: Delta to star conversion- Ra=RabRacRab+Rbc+RacRb=RabRbcRab+Rbc+RacRc=RbcRacRab+Rbc+Rac

Q: 2. If 750 μA is flowing through 11 k of resistance, what is the voltage drop across the resistor? A.…

A: Given data, Current flowing i=750 μA Resistance R=11 kΩ

Q: 4. Determine the total resistance of the circuit 10 250 ww 20 100 V www 140 ww 180 400 12 ohms a b…

A: 4) To find the total resistance of the circuit 5) To find the total current I in the circuit as…

Q: Find the percent modulation of an AM wave whose total power content is 2500 W and whose sidebands…

A: We need to find out modulation index for given AM signal .

Q: For the following circuit, G(s) = 1/s and H(s) = 1/(s+a)olest osig 40-520-mio -Y(s) X(s) + G(s) H(s)…

A: The given system is, Here, Gs=1s,Hs=1s+a.

Q: Two-watt meters, which are connected to measure the total power on a three-phase system supplying a…

A: Given data, First watt-meter P1=10.5 kW Second watt-meter P2=-2.5 kW

Q: 1. Determine the spectral components of the FM signal below. VFM 100 [sin (204.6mx106) t+…

A: According to the question, we need to analyze the equation of the FM signal.

Q: What would be the barrier potential of a silicon diode when the junction temperature is at 50°C?…

Q: A four-pole DC shunt motor, 220 V, the number of conductors in the armature 1000, the typical…

Q: 2. Calculate the total resistance between the points A and B. A www 4 ohm www 3 ohm 1 ohm 2 ohm

A: Given data, Circuit diagram is given as,

Q: 3. Find the value of Vo using superposition theorem. 6 mA 12V (1+) 6 ΚΩ ww 6 ΚΩ 6 ΚΩ 6 ΚΩ Τ Va 0

Q: 4. In an Amplitude Modulation: a) Amplitude of the carrier varies. b) Frequency of the carrier…

A: Amplitude Modulation Amplitude modulation is a type of modulation used in electronic communication,…

Q: For the circuit shown in Figure 2.54, use nodal analy- sis to find the current delivered by the 24 V…

A: As per the question, we have to find the current delivered by 24 V source.

Q: 3. Write the Boolean expression: A B + D Y

A: The given circuit is,

Q: Obtain the Fourier transform of the "switched-on" exponential function shown in Fig f(t) 1 0 e-ot

A: Fourier Transform convert time domain signal in to frequency domain. Spectra of function have…

Q: The frequency of the supply to the stator of an 8-pole induction motor is 50 Hz and the rotor…

Q: total amount of power in the series circuit. 50 V- 52 2Ω 18 2Ω

A: Voltage = 50 V Resistance R1 = 5Ω Resistance R2 = 2Ω Resistance R3 = 1Ω Resistance R4 = 2Ω

Q: Draw the energy band diagram of the solar cell following the solar cell diagram below. Indicate the…

A: According to the question, we need to draw the energy band diagram of the given solar cell as shown…

Q: 3. The voltage source in the circuit of Figure C has a current of 1A flowing out of its positive…

Q: Question 22 A receiver has a sensitivity of 1 pW and a dynamic range of 90 dB, what is the maximum…

A: Given: A receiver has, Sensitivity = 1 pW=1×10-12 W. Dynamic range = 90 dB =109 W.

Q: An 800 kV transmission line has a maximum power transfer capacity, P, it is operated at 400 kV with…

A: Let Vs be sending end voltage, VR be the receiving end voltage and X be the series…

Q: Consider an anti-aliasing filter design using the Butterworth filter. The anti-aliasing filter feeds…

A: According to the question, Consider an anti-aliasing filter design using the Butterworth filter. The…

Q: 6.3-3 A signal set has a vector representation of $₁ = (0,5) $₂=(2, 2) $3=(2, 2) (a) Assuming that…

A: According to the question, the vector representation of the signal set is given as, S1=0, 5;S2=2,…

Q: For the op-amp shown in the following figure, the voltage gain is equal to---------. 80 ΚΩ Vino 3 ΚΩ

A: The given circuit diagram is shown below:

Q: A 320V shunt motor takes a total current of 80A and runs at 1000 rev/min. If the iron, friction and…

Q: 2.14 Calculate the value of I in the circuit in Fig. P2.14. m

Q: A permanent magnet motor equipped with cobalt-samarium magnets loses 3% of its magnetism per 100°C…

Concept explainers

HVDC

HVDC stands for high voltage direct current in the electric power transmission system. The high voltage direct current system uses direct current (DC) for the transmission of electrical power through transmission lines in contrast with the alternating current that is the AC system. The HVDC is used to transmit bulk power point-to-point through long distances transmission lines. Power is rapidly transferred because the efficiency of transmission lines is greatly increased over long distances due to HVDC lines.

Question

Please solve and show your detailed solution

Number 27

Three capacitors having capacitance of 4 µF, 6 μF and 8 µF respectively are
connected in series. Find the equivalent capacitance of the combination.
A. 1.08 μF
B. 2.84 μF
C. 1.85 µF
D. 4.84 μF

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Three capacitors having values of 2.2 F, 280 F, and 470 pF are connected in parallel. What is the total capacitance?
A capacitor uses air as a dielectric and has a capacitance of 3 F. A dielectric material is inserted between the plates without changing the spacing, and the capacitance becomes 15 F. What is the dielectric constant of this material?
You are an electrician working in an industrial plant. You discover that the problem with a certain machine is a defective capacitor. The capacitor is connected to a 240-volt AC circuit. The information on the capacitor reveals that it has a capacitance value of 10 mF and a voltage rating of 240 VAC. The only 10-mF AC capacitor in the storeroom is marked with a voltage rating of 350 WVDC. Can this capacitor be used to replace the defective capacitor? Explain your answer.
The circuit is connected to a 60-Hz line. The apparent power in the circuit is 29.985 VA, and the power factor is 62.5%. The resistor has a voltage drop of 14.993 V, the inductor has an inductive reactance of 60 , and the capacitor has a capacitive reactance of 45 . ETITZVA29.985PF62.5%ER14.993VIRRPELILXL60VARsLLECICXC45VARsCC
Assume that the current flow through the resistor, IR, is 15 A; the current flow through the inductor, IL is 36 A; and the circuit has an apparent power of 10,803 VA. The frequency of the AC voltage is 60 Hz. ET ER EL IT IR15A IL36A Z R XL VA10,803 P VARSL PF L
You are working in an industrial plant. You have been instructed to double the capacitance connected to a machine. The markings on the capacitor, however, are not visible. The capacitor is connected to 560 volts and an ammeter indicates a current of 6 amperes flowing to the capacitor. What size capacitor should be connected in parallel with the existing capacitor? What is the minimum AC voltage rating of the new capacitor? What is the minimum DC voltage rating of the new capacitor? What is the minimum KVAR size that can be used in this installation?
An AC circuit contains a 24 resistor, a 15.9-mH inductor, and a 13.3F capacitor connected in parallel. The circuit is connected to a 240-V, 400-Hz power supply. Find the following values. XL=XC=IR=AIL=AIC=AP=WVARsL=VARsC=IT=AVA=PF=%=
Inductive Circuits Fill in all the missing values. Refer to the following formulas: XL=2fLL=XL2ff=XL2L Inductance (H) Frequency (Hz) Inductive Reactance ( ) 1.2 60 0.085 213.628 1000 4712.389 0.65 600 3.6 678.584 25 411.459 0.5 60 0.85 6408.849 20 201.062 0.45 400 4.8 2412.743 1000 40.841
A postage stamp mica capacitor has the following color marks starting at the upper left dot: yellow, violet, brown, green, no color, and blue. What are the capacitance value, tolerance, and voltage rating of this capacitor?
Assume that the voltage drop across the resistor, ER, is 78 V; the voltage drop across the capacitor, EC, is 104 V; and the circuit has a total impedance, Z, of 20 . The frequency of the AC voltage is 60 Hz. Find the missing values. ET ER78V EC104V IT IR IC Z20 R XC VA P VARSC PF C
Capacitive Circuits Fill in all the missing values. Refer to the formulas that follow. XC=12fCC=12fXCf=12CXc Capacitance XC Frequency 38 F 60 Hz 78.8 400 Hz 250 pF 4.5 k 234 F 10 kHZ 240 50 Hz 10 F 36.8 560 nF 2 MHz 15 k 60 Hz 75 nF 560 470 pF 200 kHz 6.8 k 400 Hz 34 F 450
You find that a 25-F capacitor connected to 480 VAC is defective. The storeroom has no capacitors with a 480-VAC rating. However, you find two capacitors rated at 50 F and 370 VAC. Can these two capacitors be connected in such a manner that they can replace the defective capacitor? If yes, explain how they are connected and why the capacitors will not be damaged by the lower voltage rating. If no, explain why they cannot be used without damaging the capacitor.