Three forces are applied to a disk of radius 0.350 m. One force is perpendicular to the rim, one is tangent to it, and the other one makes a 35° angle with the radius. What is the net torque on the disk due to these three forces around an axis perpendicular to the disk and passing through its center? IIN 35° 0-4m 16N SN O A) -2.73 N-m 10.07 N-m O B) -5.67 N-m 5.67 N-m O D) O E) -1.67 N-m

Three forces are applied to a disk of radius 0.350 m. One force is perpendicular to the rim, one is tangent to it, and the other one makes a 35° angle with the radius. What is the net torque on the disk due to these three forces around an axis perpendicular to the disk and passing through its center? IIN 35° 0-4m 16N SN O A) -2.73 N-m 10.07 N-m O B) -5.67 N-m 5.67 N-m O D) O E) -1.67 N-m

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter9: Statics And Torque

Section: Chapter Questions

Problem 1PE: (a) When opening a door, you push on it perpendicularly with a force of 55.0 N at a distance of...

See similar textbooks

Similar questions

An automobile engine can produce 200 N m of torque. Calculate the angular acceleration produced if 95.0% of this torque is applied to the drive shaft, axle, and rear wheels of a car, given the following information. The car is suspended so that the wheels can turn freely. Each wheel acts like a 15.0 kg disk that has a 0.180 m radius. The walls of each tire act like a 2.00-kg annular ring that has inside radius of 0.180 m and outside radius of 0.320 m. The tread of each tire acts like a 10.0-kg hoop of radius 0.330 m. The 14.0-kg axle acts like a rod that has a 2.00-cm radius. The 30.0-kg drive shaft acts like a rod that has a 3.20-cm radius.
(a) Give an example in which the net force acting on an object is zero, yet the net torque is nonzero, (b) Give an example in which the net torque acting on an object is zero, yet the net force is nonzero.
In analyzing the equilibrium of a flat, rigid object, you are about to choose an axis about which you will calculate torques. Which of the following describes the choice you should make? (a) The axis should pass through the objects center of mass. (b) The axis should pass through one end of the object. (c) The axis should be either the x axis or the y axis. (d) The axis should pass through any point within the object. (e) Any axis within or outside the object can be chosen.
Suppose you exert a force of 180 N tangential to a 0.280-m-radius 75.0-kg grindstone (a solid disk). (a)What torque is exerted? (b) What is the angular acceleration assuming negligible opposing friction? (c) What is the angular acceleration if there is an opposing frictional force of 20.0 N exerted 1.50 cm from the axis?
A simple pendulum consists of a small object of mass 3.0 kg hanging at the end of a 2.0-m-long light string that is connected to a pivot point. (a) Calculate the magnitude of the torque (due to the force of gravity) about this pivot point when the string makes a 5.0 angle with the vertical. (b) Does the torque increase or decrease as the angle increases? Explain. Figure P8.6
A constant net torque is applied to an object. Which one of the following will not be constant? (a) angular acceleration, (b) angular velocity, (c) moment of inertia, or (d) center of gravity.
A worker applies a torque to a nut with a wrench 0.500 m long. Because of the cramped space, she must exert a force upward at an angle of 60.0 with respect to a line from the nut through the end of the wrench. If the force she exerts has magnitude 80.0 N, what magnitude torque does she apply to the nut?
The fishing pole in Figure P10.22 makes an angle of 20.0 with the horizontal. What is the torque exerted by the fish about an axis perpendicular to the page and passing through the anglers hand if the fish pulls on the fishing line with a force F=100N at an angle 37.0 below the horizontal? The force is applied at a point 2.00 m from the anglers hands. Figure P10.22
What are the necessary conditions for equilibrium of the object shown in Figure P12.1? Calculate torques about an axis through point O.
(a) Is it possible to calculate the torque acting on a rigid object without specifying an origin? (b) Is the torque independent of the location of the origin?
A grinding wheel is in the form of a uniform solid disk of radius 7.00 cm and mass 2.00 kg. It starts from rest and accelerates uniformly under the action of the constant torque of 0.600 N m that the motor exerts on the wheel. (a) How long does the wheel take to reach its final operating speed of 1 200 rev/min? (b) Through how many revolutions does it turn while accelerating?
What is- the magnitude of the angular acceleration of a 25.0-kg disk of radius 0.800 m when a torque of magnitude 10.0 N m is applied to it? (See Section 8.5.)