Three plates are connected using welds with concurrent forces applied as shown. Calculate the resultant of the forces.

Q: If a flat plate with a circular hole is subjected to tensile force, then its theoretical stress conc...

A: If a flat plate with a circular hole is subjected to tensile force, then its theoretical stress conc...

Q: hi, can you solve this please ?

A: Given Data: The mass of water in the piston cylinder is, m=2 kg. The initial temperature of water i...

Q: Water vapor enters a turbine at a temperature of 300 ° C and a pressure of 600 kPa, leaving it as 20...

A: Given data: P1= 600kpa T1= 300 deg c P2= 20kpa

Q: A traffic light of mass 5 kg hangs from two lightweight cables, one on each side of the light. Each ...

A:

Q: can you solve this ?

A:

Q: The system in the figure, consisting of two objects with masses m1=5 kg and m2=3 kg which are attach...

A:

Q: Problem 2: (M6) A brittle material has the properties Sut=30 kpsi and Suc=90 kpsi. Using the brittle...

A: given σx=-15kpsiσy=10kpsiτxy=-15kpsiSut=30KpsiSuc=90kpsi

Q: A cylinder, a sphere and a hoop of the same masses and radii are rolling from an inclined plane. Whi...

A: given: A cylinder, a sphere and a hoop of the same masses and radii are rolling from an inclined pla...

Q: a=-15  b=40 c=0 d=0 e=0.85 vo=100cmm solve d,e,f only

A:

Q: Knowing that the coefficient of static friction between the block attached to rod ACE and the horizo...

A: Given Data θ=30°l=0.2mP=40N  and   μs=0.15Qmax=P2(3tanθ+μs)=402(3tan30°+0.15)=37.64N

Q: Which type of detector is best suited for gauging aluminum thickness, and why? a. Geiger-Mueller Tub...

A: PCE-CT 65  is a thickness gauge that uses magnetic induction i.e (ferrous) or an eddy current i.e ( ...

Q: Fluid with a density of 1200 kg/m^3 is applying pressure on the gate shown. The depth of the water i...

A:

Q: Determine the resultant of A = 30 N, 60.43° SE and B = 40 N, 45.23° N of E, C = 45 N, 66.34° S of W,...

A: Solution In Horizantal and vertical direction          ∑F=30cos60.43+40cos45.23-45cos66.34+75cos38.7...

Q: 2. Determine the second moment of area for the rectangular section with respect to an axis through t...

A:

Q: answer  (c) branch  please

A: (c) Write the given values along with suitable variables.

Q: PROBLEM 1. The shafts are made of A-36 steel and both have 100 mm diameter. If a torque of 60 kN.m i...

A:

Q: Solve c and d

A:

Q: Find the power lost in friction assuming i)uniform pressure and ii)uniform wear, when a vertical sha...

A: The diameter of the vertical shaft is, D=100 mm The rotational speed of the shaft is, N=150 rpm The ...

Q: Determine the wrong statement       A)Pumps can decrease the velocity depending on ...

A: As, it is known that pumps can not necessarily increase the velocity of a liquid because the tapered...

Q: A pump increases water pressure from 1 bar to 4 bar. If the flow rate of the water is 150 l/min, det...

A: Given the pressure is increased from 1 bar to 4 bar and the flow rate of water is 150 l/min. P1 = 1 ...

Q: Q1:- (a) Show that stream function exists as a consequence ofequation of continuity.(b) Show that po...

A: (a) Consider the stream function ψx,y,t. For two dimensional flow the velocity in the terms of strea...

Q: Show that the point of maximum entropy on the Fanno line for the adiabatic steady flow of a fluid in...

A: Fanno flow: An one dimensional adiabatic flow through a constant area duct with friction is called s...

Q: Define Reversible and Irreversible Processes for entropy ?

A: The IInd law of thermodynamics states that the entropy... of the universe is constant for a... rever...

Q: Help me fast so that I will give Upvote.

A: First of all, make a FBD of the diagram as shown below,

Q: A stream of water leaves the large tank A and fills the tank B. The output diameter of tank A is d =...

A: Given Diameter of the cylinder A = 10 m Diameter of the cylinder B = 1 m Discharge head length of cy...

Q: What is Gas turbine? Show with the complete diagram.

A: Gas turbine: A gas turbine is a combustion engine that can convert natural gas or other liquid fuels...

Q: Please solve this question.

A: Given data, C = Spring index = 8 δ= Sehim means deflection = 68 mm F = Applied axial load = 35 x103 ...

Q: A three-point bending test is conducted on a cylindrical specimen of aluminum oxide (E-400 GP2, Kım4...

A: The behaviour of the material under different loads is bending test. Given data;- Aluminium oxide, E...

Q: Wind turbine is analysed by using actuator disk theory. Show the correct change of pressure energy. ...

A: Actuator Disc Theory :-  Actuator disc theory is the simplest rotor theory possible: the rotor is re...

Q: The pump is used to transfer fluid from one location to another of different height. At inlet and ou...

A: Now applying the Bernoulli theorem pressure energy1+Kinetics Energy1+Potential energy1=pressure ener...

Q: Air at 27°C and having a flow rate of 3 x 10-4 kg/s passes through a duct with a 4 mm x 16 mm cross ...

A:

Q: Evaluate the vertical reaction on pinned support A. (q= 2t/ m P = 7t F= 5t) 12 21 87200 .f 5m +2m, 2...

A: Data given -  q = 2t/m  Here length on which q is there is = 5 m  So Q = 2t× 5 = 10t  P = 7t  F = 5t...

Q: The bridge has a length of 12 meters with a continuous linear load value at the beginning and end of...

A: Given data L=12 mW=15 N/m

Q: A pulley has 5 supporting lines and supports an 800N weight. A force of 190N is required to move the...

A: From the given data: Load = 800 N Effort required to move the weight = 190 N Number of pulley = 5

Q: A1] A small, artificial satellite of mass 10 kg and initial velocity: Vo = [3000i + 4000j] ms %3D en...

A: Given - mass of satellite 10 kg Initial velocity vo=3000i^ + 4000j^ m/s F(t) = 2000j^ + 1200tk^   N ...

Q: Answer the question Static

A:

Q: Water vapor enters a turbine at a temperature of 300 ° C and a pressure of 600 kPa, leaving it as 20...

A:

Q: Bernoulli equation is another form of ...       conservation of volume     ...

A: Given data :- Bernoulli equation is another form of ...       A.conservation of v...

Q: The steel beams shown in the figure are combined with a total of 12 rivets with a diameter of 12 mm....

A: The given shear strength of the material is

Q: A 10 30 70 1) For an A-B alloy of composition 25 wt% B (i) Draw the microstructure at T (just above ...

A: Given dataAlloy A-B of composition 25wt % BTo draw1] Microstructure just above and below the eutecto...

Q: In a piston cylinder assembly as in the figure, 0.1 m3 of saturated water at 800 kPa pressure is in ...

A: Given data: In piston-cylinder assembly, initially at state (1): At P1=800 kPa, Volume of Saturated ...

Q: 2) Find the critical damping constant c of the system shown in the figure. Choose a suitable dampi c...

A: givencritical damping constant =Ckspring constant k=90N/mmass of blockm=10kg

Q: Material science

A:

Q: The door of an oven in the kitchen of a house is 0.5 m high and 0.7 m wide. When the oven is operati...

A:

Q: Orthographic drawing Needed ( top, front and side view) there are no dimensions

A: Draw the top view (how will it look if seen from the top) for the given figure.

Q: You rejected the question, but the question already asks for internal and external diameter values. ...

A: Given data: Length of hollow steel shaft, L=3 m=3000 mm. Torque requirement is, T=25 kN.m=25×106 N.m...

Q: A bent tube is attached to a wall with brackets as shown. A force of F = 480 lb is applied to the en...

A: a) Calculate the position vector in the direction of the force. Calculate the unit vector in the di...

Q: Fluid with a density of 950 kg/m^3 and velocity of 2.632 m/sec flows through a pipe diameter of 40 m...

A: ρ=Density of fluid=950 kg/m3V=velocity of flows through a pipe=2.632 m/sD=Pipe diameter=40 mm=0.04 m...

Q: A ball bearing is moving radially outward in a slotted horizontal disk that is rotating about the ve...

A: Given, Now, write the equation of the acceleration,

Q: Material Science

A: The above question is based on Ag-Cu Eutectic system. Refer the diagrammatic representation for the ...

Types of loading

In mechanical terminology, the term load indicates that external force/weight, either constant or variable, acts on a mechanical member/structure. The weight of an object of a specific material is also an external load, and the external force that works on a structure comes under the categories of loading. The external load generates its effects as stress and strain in the structure.