answer (c) branch please Where k is the thermal conductivity of its material, A is the crosssectional area and T=T(x) is the temperature distribution. Fortan(x) sec(x) + sin(x²), k=0.7 and A= 10 find Q atа. Т(х)x=T/3.b. T(x) = Vxcos(4x) +, find Q at x = T/2.= x (x2-cos(2x)), find Q at x = 1/4.хcos(4x) +с. Т(x) — хd. T(x) = 100e-3x + In(4x), k=470, A= 0.01n and x= 1/3; Task 2The heat transfer rate of the rocket engine is given by:dTQ = -kAdx

(c) Write the given values along with suitable variables.

Where k is the thermal conductivity of its material, A is the cross sectional area and T=T(x) is the temperature distribution. For a. T(x) = tan(x) sec(x) + sin(x²), k=0.7 and A= 10 find Q at x=T/3. b. T(x) 1 xcos(4x) +, find Q at x = T/2. -x (x2-cos(2x). x2 с. Т(х) — х d. T(x) find Q at x = T/4. — 100е 3х + In(4x), k3470, А3 0.01п and x— 1/3;

Where k is the thermal conductivity of its material, A is the cross sectional area and T=T(x) is the temperature distribution. For a. T(x) = tan(x) sec(x) + sin(x²), k=0.7 and A= 10 find Q at x=T/3. b. T(x) 1 xcos(4x) +, find Q at x = T/2. -x (x2-cos(2x). x2 с. Т(х) — х d. T(x) find Q at x = T/4. — 100е 3х + In(4x), k3470, А3 0.01п and x— 1/3;

Refrigeration and Air Conditioning Technology (MindTap Course List)

8th Edition

ISBN:9781305578296

Author:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Publisher:John Tomczyk, Eugene Silberstein, Bill Whitman, Bill Johnson

Chapter40: Typical Operating Conditions

Section: Chapter Questions

Problem 10RQ: The seasonal energy efficiency ratio (SEER) includes the energy used in the _____and _____cycles.

See similar textbooks

Similar questions

A 20-KW motor with 80% efficiency drives a centrifugal pump delivery 0.08m3/sec against a head of 20m. Determine the pump efficiency
The energy wasted as compressed air escapes through the leaks is equivalent to the energy it takes to compress it.
Theoretical horsepower required to pump water at 100 GPM from a larger reservoir to the surface of another reservoir 400 feet higher is?
A submersible pump deliver 350 gpm of water to a height of 5ft from the ground. the pump was installed 120 ft. below the ground level and a draw down of 8 ft. during the operation, if water level is 25 ft. above the pump, determine the pump power
A pump is driven by an electric motor moves 35 gal/min of water from reservoir A to reservoir B, lifting the water to a total head of 245 ft. The efficiency of the pump and motor are 64% and 84% respectively. What size of motor (HP) is required? a. 3 hp b. 5 hp c. 4 hp d. 7 hp
How much flow energy in kW required to move 3000liters/min. of water inside the pipe against a pressure whose value is ranging from 100kPa to 300kPa?
A submersible pump delivers 350 gpm of water to a height of 5 ft from the ground. The pump were installed 150 ft. Below the ground level and a draw down of 8 ft during the operation. If water level is 25 ft above the pump. Determine the pump power.
2 Daniel also gets an internship, but it's for a 6 story hospital. To ensure adequate water supply, they pump the water to a storage tank on the roof (65 m above ground). If the pump is located 5 m below ground and applies a pressure of. He needs to pump water from a storage tank, located 3 m underground, and make sure it has enough pressure so that it can adequately supply water to a building. If the pump supplies a pressure of 8.5 atm, what will be the speed of the water as it flows into the storage tank at the top of the building? 12 m/s 5 m/s 23 m/s 8 m/s
What size pump is needed to supply 10 gpm to a cylinder when the electric motor is rotating at 1725 rpm? Assume 100% efficiency and state your answer in in3/rev to two decimal places.?
3.4 Find the flow rate of water through the system shown for the turbine to produce 20 kW. Neglect friction in your calculations
A pump recieves 8kgs of water at 220 kPa and 110℃ and discharges it at 1100 kpa. Compute the power required in kW.
While the pressure remains constant and 99.7 psia, the volume of air changes from 12 cubic feet to 20 cubic feet. Find the amount of work done on or by the closed system.