To improve the energy efficiency of a synchronous rectifier, (a) A low voltage MOSFET with a very low rɔ5(0m) and a high voltage BJT with a very low on-state voltage are used (b) A high voltage MOSFET with a very low rɔs(om) and a low voltage BJT with a very low on-state voltage are used (c) A low voltage MOSFET with a very low rɔs(cm) and a low voltage BJT with a very low on-state voltage are used (d) A high voltage MOSFET with a very low rɔs(cm) and a high voltage BJT with a very low on-state voltage are used

To improve the energy efficiency of a synchronous rectifier, (a) A low voltage MOSFET with a very low rɔ5(0m) and a high voltage BJT with a very low on-state voltage are used (b) A high voltage MOSFET with a very low rɔs(om) and a low voltage BJT with a very low on-state voltage are used (c) A low voltage MOSFET with a very low rɔs(cm) and a low voltage BJT with a very low on-state voltage are used (d) A high voltage MOSFET with a very low rɔs(cm) and a high voltage BJT with a very low on-state voltage are used

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter30: Dc Motors

Section: Chapter Questions

Problem 6RQ: What is CEMF?

See similar textbooks

Similar questions

What is CEMF?
A 4:1 transformer is connected to a bridge rectifier circuit with a 1kΩ load. What is the peak output current of the circuit if the input voltage is 250Vrms? Express your answer in mA.
Given the emitter follower schematic below and the following information: Vi = 2V β = 100 VCE,Sat = 0V VBE,On = 0.7V VFWD = 0.7V (Forward voltage of diode) Determine the values of VB (Base Voltage) and V0 (Output/Emitter Voltage).Also, determine the state of operation of the BJT and the diode.
Determine the DC Voltage for the filtered bridge rectifier with a load as indicated in Figure
Questions: Draw a circuit using:a. 2 switches (S1 & S2) to build an equivalent AND gate. Indicate output signal using LED.b. 2 transistors (S1 & S2) to build an equivalent AND gate. Indicate output using LED. c. 2 switches (S1 & S2) to build an equivalent OR gate. Indicate output signal using LED.d. 2 transistors (S1 & S2) to build an equivalent AND gate. Indicate output using LED.
Explain the operation of the diode in the full-wave bridge rectifier, the zener diode in a voltage stabiliser and the bipolar transistor as an amplifier. Please dont copy and try to answer in written on paper i will like
Create this using LTSpice B. Simulation showing each required output/waveform.a. Output of transformerb. Output of rectifierc. Output of filterd. Zener diode or load output
1.)Draw the diagram /circuit equivalent of 4 transistor Q1, Q2, Q3 & Q4. Connect it to form A.) Diac circuit B.) Triac circuit
A fully controlled, single-phase bridge rectifier is powered from an ideal 220V, 50Hz source. The rectifier is triggered with a trigger angle of 60 degrees and provides a smooth current of 50A to the load at the output. According to this: a) Draw the waveform of the output voltage in scale and calculate the average value of the output voltage. Combine the average voltage signal with the output voltage wave signal. Show on the same figure. b) Draw the waveforms of the thyristor currents, the gap diode current and the current drawn from the source in scale. c) Calculate the value of the filter inductance used at the output when the ripple in the load current is 3A. (Do the operations by showing the output voltage shapes and areas on the figure. The answers should be in the system and order in the solved examples.)
The ________parameters may not reflect the actual operating conditions but simply provide an indication of the level of each parameter to expect for general use. a.hybrid-pi b.hybrid c.pi d.re
A conductor carries a current that is equivalent to a 5 A continuous current in one direction and a superimposed full-wave rectifier current in the opposite direction. What is the maximum value of the latter if the average conductor current is zero?
ANSWER ALL QUESTIONS, QUICKLY 2. For a UJT, it turns off when the voltage at the emitter reaches a. turn off voltage, b valley voltage, c. a negative voltage, d. peak voltage 3. resistive control gate circuits have a limitation on the maximum firing delay angle. What can be done to increase the firing delay? a. adding a capacitor, b. using a UJT, c. adding a diode, d. all og the above. 4. it is a three terminal breakover type of device that will turn on when the peak voltage at the emitter is achieved a. BJT, b. UJT, c. FET, d. SCR 5. The turn on voltage if a UJT is dependent on a. external resistors, b. instrinstic standoff voltage, c. supply voltage, d. intrinsic standoff voltage and supply voltage