Transformer pole steps down up voltage entering homes on Transformer steps voltage for before transmission Distribution line Power plant carries electricity to generates the house. Neighborhood transformer steps carries down voltage | electricity Transmission line electricity over long distances 1. 4. 2. 5. 3. 6.

Transformer pole steps down up voltage entering homes on Transformer steps voltage for before transmission Distribution line Power plant carries electricity to generates the house. Neighborhood transformer steps carries down voltage | electricity Transmission line electricity over long distances 1. 4. 2. 5. 3. 6.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.59P

See similar textbooks

Similar questions

Which termination would result to a phase change of 180 degrees at the load if Zo = 100 ohm? a. 50 ohm b. short circuit c. 75 ohm d. all of these What is the purpose of impedance matching? a. maximum return loss b. maximum SWR c. maximum load power d. maximum reflection A short piece of transmission line that may be open or shorted and used for impedance matching purposes. a. converter b. decoder c. stub d. transformer
The following data were obtained on a 2.5 MVA, 50-Hz, 19.1-kV:3.81-kV single-phase transformertested at 50 Hz:Voltage (V) Current (A) Power (kW)LV winding with HV terminals open-circuited: 3810 9.86 8.14HV winding with LV terminals short-circuited: 920 141 10.3a. Calculate the cantilever equivalent-circuit parameters as referred to the transformer high-voltagewinding.b. Calculate the cantilever equivalent-circuit parameters as referred to the transformer low-voltagewinding.c. With the transformer carrying rated load and rated voltage at its low-voltage terminal, calculate thepower dissipated in the transformer.d. Repeat part a and b in per-unit. Compare and comment on your result.
The power system insulation problem involves a. Capacitance of earth and subsequent grounding b. Selection of basic insulation level of system equipment c. Determination of single phase line insulation d. Determination of three phase line insulation Clear my choice
The figure below shows a radial transmission system with a generator having a terminalvoltage of 95 KV at angle of10.5°. The load demand is 50 MW at a power factor of 0.88 lagging.Use a base of 128.4MVA . Instructions :round of to 2 decimal places. Calculate the following : 1.Load current (A) and Base current (A) 2Per unit impedance of transformer 2 and Per unit impedance of transformer 1.3.Per unit voltage of the generator. And Per unit voltage of the line. 4.Per unit voltage of the transformer 1 5.Per unit impedance of the line.6.Resistance of the transmission line when the load consumes full-load (Ω).
Consider the microgrid of Figure 3.66. A three-phase transformer, T1, israted at 500 kVA, 220 VY grounded/440 V delta, a transformerwith a reactance of 3.5%.Themicrogridis supplied from anAC bus of a PV generating station.The DC bus rated at 540 V.The distributionlineis 10mileslong and has a series impedance of 0.1 + j1.0 Ω per mile and local load of 100 kVA at 440 V. The microgrid is connected to the local power grid using a three-phase transformer T2, rated at 440 V Y grounded/13.2 kV delta,500 kVA with a reactance of 8%. Compute the per unitimpedance diagram of the microgrid system. Assume the voltage base of 13.2 kV on the local power grid side and kVA base of 500
SUBJECT: Elements of Electrical Machines DesignINSTRUCTIONS: - Please write clearly and understandable way. - Write all the corresponding Given with their corresponding symbols and units. - Draw/Illustrate the diagram/circuit or drawings that is related to the problem, IF POSSIBLE, which is HIGHLY REQUIRED. - Solve in step-by-step, no shortcut - Underline twice the Final Answer.PROBLEM: A 13800 / 480 V, 3-phase transformer bank is connected as a wye-delta configuration. What must be the turns ratio of each transformer?
The following data were obtained from a short-circuit test performed upon a 50 kVA, 2300/115 V, 60 Hz transformer: Esc = 87 V, Isc = 21.75 A, Psc = 590 W. Calculate (a) equivalent resistance, reactance and impedance referred to the primary, and (b) voltage regulation at a power factor of 0.866 lagging. Subject: Electrical Apparatus and Devices
2.A 10 kVA, 1000 V / 200 V, 50 Hz, single phase transformer has HV and LV sidewinding resistances as 1.1 Ωand 0.05 Ω respectively. The leakage reactances of HV and LV sides are respectively 5.2 Ω and 0.15 Ωrespectively. Calculate [i] the voltage to be applied to the HV side in order to circulate rated current with LVside shorted, [ii] Also calculate the power factor under this condition.
Solve the following problems with complete solutions and unitsusing two(2) decimal digits. Use your own analysis andcomputations. 2. A 3-phase transformer, ratio 33/6.6-kV, Δ-Y, 2-MVA has a primary resistance of 8 Ω per phase and a secondary resistance of 0.08 Ω per phase. The percentage impedance is 7%. Calculate the secondary voltage with rated primary voltage and hence the regulation for full-load 0.75 power factor lagging conditions.
The efficiency of a 20 kVA 15.4 / 0.4 kV three-phase power transformer is 74,1% for a load with unity power factor at rated power. Relative short circuit voltage% Uk = 30.0 and relative no-load current% I0 = 30. Since the transformer (Star-delta) is connected; Note: In 3-phase electrical machines, the current-voltage information given on the label is always line values. Phase valueWhen given, it must be specified separately. Therefore, all current-voltage information given in the question are line values. 1-) Draw the primary reduced equivalent circuit. 2-) What is the power value measured in the short circuit test of this transformer? 3-) What is the iron loss value of this transformer ?
An Electrical engineer is asked by a client to prepare a technical specification on specific items connected with a project. Hence, the engineer is requested to prepare the technical specification of the following: PROJECT: A Subdivision Development Lot AREA; 2 Hectares LOCATION: Brgy. Kanlurang Mayao, Lucna City Technical specification of fuse cutout Technical specification of transformer
A 50 kVA, 2,400/480V., single-phase distribution transformer has a primary and secondary winding impedances of 5.0 + j10 and 0.2 + j0.45 ohms respectively. Calculate the voltage across the secondary terminals at full load, 85% power factorlagging when the primary is supplied with 2,400 volts.