A 50 kVA, 2,400/480V., single-phase distribution transformer has a primary and secondary winding impedances of 5.0 + j10 and 0.2 + j0.45 ohms respectively. Calculate the voltage across the secondary terminals at full load, 85% power factorlagging when the primary is supplied with 2,400 volts.

A 50 kVA, 2,400/480V., single-phase distribution transformer has a primary and secondary winding impedances of 5.0 + j10 and 0.2 + j0.45 ohms respectively. Calculate the voltage across the secondary terminals at full load, 85% power factorlagging when the primary is supplied with 2,400 volts.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.4P: A single-phase 100-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down...

See similar textbooks

Related questions

Q: Consider a bank of three single-phase two-winding transformers whose high-voltage terminals are…

A: Two connected windings on the same core are modelled by the single-phase two-winding transformer.…

Q: A 100 KVA, 2000/200V 1-phase 2-winding Transformer is to be used as an auto transformer for stepping…

Q: a) What is the minimum required transformer rating in kVA? b) By what percentage could the required…

A: It is given that:

Q: A three-phase generator step-up transformer i

Q: Problem-13 A50-kVA, 13,800/208-V, 4-Y distribution transformer has a resistance of 1 percent and a…

Q: A 200 – MVA, 15/200 kV single-phase power transformer has a per – unit resistance of 1.2 percent…

A: Part (1): Consider the base voltage to be 15 V and the base MVA to be 200 MVA. Since the base…

Q: An 11,000/230-V, 150-kVA, 50-Hz, 1-phase transformer has a core loss of 1.4 kW and full-load Cu loss…

Q: 2. A 3-phase, 6,600/415-V, 2,000-kVA transformer has a per unit resistance of 0.02 and a per unit…

Q: A 40000-KVA, 25000-V/600-kV, single phase transformer has the following series impedances: Z1=…

Q: Consider that three single-phase transformers are connected as Delta in the primary and Wye in the…

Q: Impedance of single phase., two winding transformer referred to primary side is 0.1 + j0.6 p.u. The…

A: Given values are - S=1kVAZPP.U=0.1+j0.6V1V2=200400

Q: A single-phase 100-kVA, 2400/240-volt, 60-Hz distribution transformer is used as a step-down…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: 1. Consider a three-phase transformer with a rating of 700 MVA and a secondary voltage of 145 kv.…

Q: Questions:- 1. What happen when the two transformers are operated in parallel having un equal turn's…

A: According to the bartleby's guidelines we have to solve only one question posted by students so…

Q: d) An 11kV/41 V, 3-phase transformer supplies a 20hp, 415V 3-phase motor with rated voltage and…

Q: The % resistance and the % leakage reactance of a 5 kVA, 220 V / 440 V, 50 Hz, single phase…

A: Given values are - Resistance%=3%ResistancePer unit=0.03Reactance%=4%ReactancePer…

Q: Three single phase transformers, each rated at 12kVA, 120/240V, 60Hz, are connected to form a…

A: Given data : Each rating of transformer =12 KVA Power factor =0.8 lagging

Q: Data from short-circuit and open-circuit tests of a 25-kVA, 6900-230 V, 60 Hz transformer are given…

Q: A 120-VA 130/13 V transformer is to be connected so as to form a step-up auto- transformer. The…

A: Given two winding transformer with 120 VA 130/13 v Series resistance and reactance is 1% and 8 % per…

Q: Two transformers rated at 100 kVA each are connected in an open-delta connection. What is the total…

A: NOTE: We’ll answer the first question since the exact one wasn’t specified. Please submit a new…

Q: 60 KVA, 415-220 V, 50 Hz transformer I.(exciting current)=2% of the rated current current at 0.75…

Q: a) Draw a reactance diagram for the circuit. b)Determine the voltage at the primary side of the…

Q: Consider a single phase transformer of rating 150 KVA, 3600/360, 50 Hz. Let the series resistance…

A: Formula to calculate voltage required to produce rated current at short circuit is: VSC=V1×ZPUwhere…

Q: The efficiency of a 400 kVA, 1-phase transformer is 95 % when delivering full load at 0.8 power…

Q: 2. An open delta transformer bank server a balance 3 phase load of 65 kVA at 250 volts and phase…

Q: Consider a single phase transformer of rating 150 KVA, 1500/150, 50 Hz. Let the series resistance…

A: Given: Z1=R1+jX1=0.2+j0.45 ΩZ2=R2+jX2=0.002+j0.0045 ΩKVA=150

Q: An open delta transformer bank server a balance 3 phase load of 70 kVA at 240 volts and phase angle…

A: The solution is given below.

Q: A 400/100 V, 5 kVA single-phase two winding transformer is to be used as an auto-transformer to…

A: It is given that: two winding transformer:400/100 Vcosϕ=0.8 laggingη=0.95 %Auto transformer:500/400

Q: 3.9. A 400-MVA, 240-kV/24-KV, three-phase Y-A transformer has an equivalent series impedance of 1.2…

Q: ) A 500 kVA single-phase transformer A with percentage impedance of 0.010 + j0.05 is connected in…

Q: A 500 kVA, 3-Phase ,11 kV / 430 V distribution transformer with the equivalent percent resistance…

A: Given, Three Phase Transformer Voltage Rating= 11 KV/ 430V Output power= 500 KVA Equivalent…

Q: Consider a 3-phase transmission line operating at 66 KV and connected through a 1000 KVA transformer…

Q: Q2: A 5kVA, 200/400V, 50Hz single phase transformer gave the following test figures: No-load:…

A: Given values are = 5kVA, 200/400V, 50Hz single phase transformer. Tests results are = No-load:…

Q: A single-phase two-winding transformer rated 90 MVA, be connected as an autotransformer rated 80/200…

Q: A 600 kVA, 1-phase transformer has an efficiency of 92 % both at full-load and half- load at unity…

A: Given, Output kVA rating = 600 kVA Efficiency, η=92 % (both at full-load and half-load) Power…

Q: Example 1: A single-phase, 100-kVA, 1000:100-V, 60-Hz transformer has the following test results:…

Q: A 10-kVA, 2200/400 V, single phase distribution transformer has a primary and secondary winding…

A: Given that 10-kVA, 2200/400 V, single phase distribution transformer primary and secondary winding…

Q: The nameplate on a 7.97-kV:266-V, 25-kVA single-phase transformer indicates that it has a series…

A: Given: Series reactance, Xs=7.5%=0.075pu V=7.97KV/266V S=25KVA a)Series reactance in both the sides.…

Q: A 400-MVA, 240-kV/24-KV, three-phase Y-A transformer has an equivalent series impedance of 1.2 + j6…

A: According to the question we have to find the line-to-line voltage at high terminals of the…

Q: Power transformer A, has Rated power of 150MVA. Line voltage of 330/66 kV Frequency=50Hz Connection…

A: The Figure shows the load sharing in two transformers referred to HV side. V2 = E2A -IAZA…

Q: 2. An open delta transformer bank server a balance 3 phase load of 70 kVA at 240 volts and phase…

A: The solution can be achieved as follows.

Q: A 50-kVA 13.8-kV/208-V (rms, line-line) ∆−Ythree-phase distribution transformer has a per-unit…

A: Dear student as per our guidelines we are supposed to solve only one question in which it should…

Q: (b) In a transformer test, data from short circuit and open circuit tests of a 75-kVA, 4600-230V,…

Q: Three-phase, 2-winding, 12 MVA, 30/132 kV, star/delta, 50 Hz transformer of equivalent leakage…

A: XL is leakage reactance referred to secondary side. The phasor diagram is

Q: Per-Unit System 3) If a 250MUA,11/400 KU, Three-Phase power Transformer has Zpu of 0.05 pu on the…

Q: A 35 kVA, single-phase transformer is tested on both open-circuit and short-circuit condition,…

A: Efficiency = output power/input power. Cupper loss is varies with load and iron loss is constant at…

Q: A 50-kVA 13.8-kV/208-V (rms, line-line) ∆ − Y three-phase distribution transformer has a per unit…

A: Given,High voltage side, line voltage(Base) =13.8 kVApparent power (S)(Base)=50 kVAa) As primary is…

Q: A 5000-KVA 230/13.8-kV single-phase power transformer has a per-unit resistance of 1 percent and a…

A: In this question we need to find a equivalent circuit referred to LV side of transformer , voltage…

Q: single-phase 50-kVA, 2400/240-volt, 60-Hz distribution transformer is used as a step-down…

Q: A 400-MVA, 240-kV/24-KV, three-phase Y-A transformer has an equivalent series impedance of 1.2 + j6…

A: Delta-Star transformer- A Delta-Star transformer is a transformer whose primary side is in delta…

Concept explainers

Single Phase Transformer

A single-phase transformer is a type of power transformer. It is an electrical device that accepts converts the single phase alternating power into single phase alternating power. In this power conversion the voltage is stepped up or down. If the voltage is stepped up, the current will be stepped down and if the voltage is stepped down, the current will be stepped up.

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An infinite bus, which is a constant voltage source, is connected to the primary of the three-winding transformer of Problem 3.53. A 7.5-MVA,13.2-kV synchronous motor with a sub transient reactance of 0.2 per unit is connected to the transformer secondary. A5-MW,2.3-kV three-phase resistive load is connected to the tertiary Choosing a base of 66 kV and 15 MVA in the primary, draw the impedance diagram of the system showing per-unit impedances. Neglect transformer exciting current, phase shifts, and all resistances except the resistive load.
Consider the single-line diagram of the power system shown in Figure 3.38. Equipment ratings are Generator 1: 1000MVA,18kV,X=0.2perunit Generator 2: 1000MVA,18kV,X=0.2p.u. Synchronous motor 3: 1500MVA,20kV,X=0.2p.u. Three-phase -Y transformers T1,T2,T3,T4,: 1000MVA,500kV,Y/20kV,X=0.1p.u. Three-phase YY transformer T5: 1500MVA,500kV,Y/20kVY,X=0.1p.u. Neglecting resistance, transformer phase shift, and magnetizing reactance, draw the equivalent reactance diagram. Use a base of 100 MA and 500 kV for the 50-ohm line. Determine the per-unit reactances.
PowerWorid Simulator case Problem 3_60 duplicates Example 3.13 except that a resistance term of 0.06 per unit has been added to the transformer and 0.05 per unit to the transmission line. Since the system is no longer lossless, a field showing the real power losses has also been added to the oneline. With the LTC tap fixed at 1.05, plot the real power losses as the phase shift angle is varied from 10 to +10 degrees. What value of phase shift minimizes the system losses?
Consider Figure 3.4. For an ideal phase-shifting transformer, the imda nce is unchanged when it is referred from one side to the other. (a) True (b) False
A two-winding single-phase transformer rated 60kVA,240/1200V,60Hz, has an efficiency of 0.96 when operated at rated load, 0.8 power factor lagging. This transformer is to be utilized as a 1440/1200-V step-down autotransformer in a power distribution system. (a) Find the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the ratings as a two-winding transformer. Assume an ideal transformer. (b) Determine the efficiency of the autotransformer with the kVA loading of part (a) and 0.8 power factor leading.
Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows: XY15MVA,13.8/138kV, leakage reactance 10 YZ15MVA,138/69kV, leakage reactance 8 With the base in circuit Y chosen as 15MVA,138kV determine the per-unit impedance of the 500 resistive load in circuit Z, referred to circuits Z, Y, and X. Neglecting magnetizing currents, transformer resistances, and line impedances, draw the impedance diagram in per unit.
A single-phase two-winding transformer rated 90MVA,80/120kV is to be connected as an autotransformer rated 80/200kV. Assume that the transformer is ideal. (a) Draw a schematic diagram of the ideal transformer connected as an autotransformer. showing the voltages, currents, and dot notation for polarity. (b) Determine the permissible kVA rating of the autotransformer if the winding currents and voltages are not to exceed the rated values as a two-winding transformer. How much of the kA rating is transferred by magnetic induction?
In developing per-unit equivalent circuits for three-phase transformers. under balanced three-phase operation. (i) A common Sbase is selected for both the H and X terminals. (ii) The ratio of the voltage bases Vbase/VbaseX is selected to be equal to the ratio of the rated line-to-line voltages VratedHLL/VratedXLL. (a) Only one of the above is true. (b) Neither is true. (C) Both statements are true.
The ratings of a three-phase three-winding transformer are Primary(1): Y connected 66kV,15MVA Secondary (2): Y connected, 13.2kV,10MVA Tertiary (3): A connected, 2.3kV,5MVA Neglecting winding resistances and exciting current, the per-unit leakage reactances are X12=0.08 on a 15-MVA,66-kV base X13=0.10 on a 15-MVA,66-kV base X23=0.09 on a 10-MVA,13.2-kV base (a) Determine the per-unit reactances X1,X2,X3 of the equivalent circuit on a 15-MVA,66-kV base at the primary terminals. (b) Purely resistive loads of 7.5 MW at 13.2 kV and 5 MW at 2.3kV are connected to the secondary and tertiary sides of the transformer, respectively. Draw the per- unit impedance diagram, showing the per-unit impedances on a 15-MVA,66-kV base at the primary terminals.
A 10-kVA, 2200/400 V, single phase distribution transformer has a primary and secondary winding impedances of 5 + j12 and 0.25 + j0.45 ohms, respectively. Calculate the voltage across the secondary terminals at full load, 90 % power factor lagging, when the primary is supplied with 2200 volts?
An open delta transformer bank server a balance 3 phase load of 70 kVA at 240 volts and phase angle of 30 degrees lagging. Calculate the real, reactive, apparent powers and pf at which each transformer is operating.
A 10kVA 2000/400V single phase distribution transformer has a primary and secondary winding impedances of 0.5+j10 and 0.2+j0.45 ohms. Calculate the voltage across the secondary terminals at full load, 80% pf lagging, when the primary is supplied with 2000 volts?