True or False Only the net force acting on an object can do work. True or False If a particle remains at rest, then we can conclude that there is no work done on it. True or False A force that is perpendicular to the velocity of the object is not doing work to the object. True or False The force that causes the acceleration of an object following a circular path at a constant speed does work on the object.

True or False Only the net force acting on an object can do work. True or False If a particle remains at rest, then we can conclude that there is no work done on it. True or False A force that is perpendicular to the velocity of the object is not doing work to the object. True or False The force that causes the acceleration of an object following a circular path at a constant speed does work on the object.

Physics for Scientists and Engineers, Technology Update (No access codes included)

9th Edition

ISBN:9781305116399

Author:Raymond A. Serway, John W. Jewett

Publisher:Raymond A. Serway, John W. Jewett

Chapter7: Energy Of A System

Section: Chapter Questions

Problem 7.44P: (a) Suppose a constant force acts on an object. The force does not vary with time or with the...

See similar textbooks

Similar questions

a shopper in a supermarket pushes a cart with a force of 35 N directed at an angle of 25 below the horizontal. The force is just sufficient to overcome various frictional forces, so the cart moves at constant speed, (a) Find the work done by the shopper as she moves down a 50.0-m length aisle, (b) What is the net work done on the cart? Why? (c) The shopper goes down the next aisle, pushing horizontally and maintaining the same speed as before. If the work done by frictional forces doesnt change, would the shoppers applied force be larger, smaller, or the same? What about the work done on the cart by the shopper?
Alex and John are loading identical cabinets onto a truck. Alex lifts his cabinet straight up from the ground to the bed of the truck, whereas John slides his cabinet up a rough ramp to the truck. Which statement is correct about the work done on the cabinet-Earth system? (a) Alex and John do the same amount of work, (b) Alex does more work than John, (c) John does more work than Alex, (d) None of those statements is necessarily true because the force of friction is unknown, (e) None of those statements is necessarily true because the angle of the incline is unknown.
Integrated Concepts A 75.0-kg cross-country skier is climbing a 3.0° slope at a constant speed of 2.00 m/s and encounters air resistance of 25.0 N. Find his power output for work done against the gravitational force and air resistance. (b) What average force does he exert backward on the snow to accomplish this? (c) If he continues to exert this force and to experience the same air resistance when he reaches a level area, how long will it take him to reach a velocity of 10.0 m/s?
Give an example of a situation in which there is a force and a displacement, but the force does no work. Explain why it does no work.
The "shot" used in the shot-put event is a metal ball with a mass of 7.3 kg. When thrown in Olympic competition, it is accelerated to a speed of about 14 m/s. As an approximation, let's say that the athlete exerts a constant force on the shot while throwing it and that it moves a distance of 3 m while accelerating. (a) What is the shot's kinetic energy? (b) Compute the force that acts on the shot. (c) It takes about 0.5 s to accelerate the shot. Compute the power required. Convert your answer to horsepower.
The chin-up is one exercise that can be used to strengthen the biceps muscle. This muscle can exert a force of approximately 8.00 102 N as it contracts a distance of 7.5 cm in a 75-kg male.3 (a) How much work can the biceps muscles (one in each arm) perform in a single contraction? (b) Compare this amount of work with the energy required to lift a 75-kg person 40. cm in performing a chin-up. (c) Do you think the biceps muscle is the only muscle involved in performing a chin-up?
Integrated Concepts (a) What force must be supplied by an elevator cable to produce an acceleration of 0.800 m/s2 against a 200-N frictional force, if the mass of the loaded elevator is 1500 kg? (b) How much work is done by the cable in lifting the elevator 20.0 m? (c) What is the final speed of the elevator if it starts from rest? (d) How much work went into thermal energy?
(a) Suppose a constant force acts on an object. The force does not vary with time or with the position or the velocity of the object. Start with the general definition for work done by a force W=ifFdr and show that the force is conservative, (b) As a special case, suppose the force F =(3i + 4j)N acts on a particle that moves from O to in Figure P7.43. Calculate the work done by F on the particle as it moves along each one of the three paths shown in the figure and show that the work done along the three paths identical.
A force F(x)=(5.0x2+7.0x)N acts on a particle as it moves along the positive x-axis. (a)How much work does the force do on the particle as it moves from x2.0 to x=5.0 m? (b) Picking a convenient reference point of the potential energy to be zero at x=, find the potential energy for this force.
A 60.0-kg athlete leaps straight up into the air from a trampoline with an initial speed of 9.0 m/s. The goal of this problem is to find the maximum height she attains and her speed at half maximum height. (a) What are the interacting objects and how do they interact? (b) Select the height at which the athletes speed is 9.0 m/s as y = 0. What is her kinetic energy at this point? What is the gravitational potential energy associated with the athlete? (c) What is her kinetic energy at maximum height? What is the gravitational potential energy associated with the athlete? (d) Write a general equation for energy conservation in this case and solve for the maximum height. Substitute and obtain a numerical answer. (e) Write the general equation for energy conservation and solve for the velocity at half the maximum height. Substitute and obtain a numerical answer.
In 1990 Walter Arfeuille of Belgium lifted a 281.5-kg object through a distance of 17.1 cm using only his teeth. (a) How much work did Arfeuille do on the object? (b) What magnitude force did he exert on the object during the lift, assuming the force was constant?
(a) A child slides down a water slide at an amusement park from an initial height h. The slide can be considered frictionless because of the water flowing down it. Can the equation for conservation of mechanical energy be used on the child? (b) Is the mass of the child a factor in determining his speed at the bottom of the slide? (c) The child drops straight down rather than following the curved ramp of the slide. In which case will he be traveling faster at ground level? (d) If friction is present, how would the conservation-of-energy equation be modified? (e) Find the maximum speed of the child when the slide is frictionless if the initial height of the slide is 12.0 m.