Two 2200/110 V, transformers are operated in parallel to share a load of 250 kVA at 0.85 power factor lagging. Transformers are rated as below: A: 100 kVA ; 0.9% resistance and 10% reactance B: 100 kVA ; 1.0% resistance and 5% reactance Find the load carried by each transformer.

Two 2200/110 V, transformers are operated in parallel to share a load of 250 kVA at 0.85 power factor lagging. Transformers are rated as below: A: 100 kVA ; 0.9% resistance and 10% reactance B: 100 kVA ; 1.0% resistance and 5% reactance Find the load carried by each transformer.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.4P: A single-phase 100-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down...

See similar textbooks

Related questions

Q: Three 2X -kVA, 34500/277-V transformers are connected in a A-Y configuration. The short-circuit test…

A: Given data, Three 28 kVA, 34500/277 V transformers are connected in a Δ-Y configuration.…

Q: The primary and secondary winding resistances of a 30 KVA, 6600 /250 V, 1 phase transformer are 8…

Q: The primary of a certain transformer, with and open-circuit secondary, takes 1A at a power factor of…

A: Given I2=50Apower factor ϕ0=0.4power factor ϕ2=0.8

Q: Two single-phase transformers whose phase electrical equivalent circuits are given below are…

A: Since both the transformer are connected in parallel,we can draw the each transformer equivalent…

Q: Example 33.9. A 2000-kVA, 6,600/400-V, 3-phase transformer is delta-connected on the high voltage…

Q: A) What happens to the 12/220 transformer if we use the wooden core (one piece)? and then in the…

A: Transformer: It is a static device. The transformer is convert the electrical power from one…

Q: A transformer shown in Figure 10 is needed that will cause an actual load resistance of 250 to…

A: (a) Redraw the given circuit diagram.

Q: A single phase transformer takes 10 A on no load at p.f. of 0.2 lagging. The turns ratio is 4: 1…

A: We have a single phase transformer having, No-load current (I) = 10 A Power factor (Cos ϕ0) = 0.2…

Q: Analysis of an Ideal Transformer Circuit The turns ratio of the step-up transformer in Figure 2 is…

Q: a 100 kva, 1100/220 v, 50 hz, single-phase transformer has a leakage impedance of (0.1 +0.40) ohm…

A: Single Phase Transformer-A Single Phase Transformer is a power Transformer. It is made up of one…

Q: A) Two 1-phase transformers with equal turn ratio have impedances of (0.5 + j3) and (0.6+j10) with…

A: The parallel configuration of transformer in s distribution system or load driving application helps…

Q: Based on the following power system, both transformers are equipped with tap changing facilities…

A: In the given power system, it is given: The impedance of the line and transformers at 132 kV:-…

Q: A) A single-phase transformer with a ratio of 440/110-V takes a no-load current of 5A at 0.2 power…

A: In the single phase transformer. What is primary current Ip = Io + IS ' Where Is' is secondary…

Q: A 400-kVA transformer has a primary winding resistance of 12 and a secondary winding resistance of…

Q: (c) In a 25 KVA, 1000/400 V, 1- o transformer, the core loss and full load copper losses are 200 W…

A: Efficiency = (output power/input power )×100. Input power = output power + iron losses + copper…

Q: Two three-phase transformers of equal voltage ratios are operating in parallel. The load draws a…

A: Given: load current IL=200∠-cos-10.9IL=200∠-25.84° AZ1=0.1+j0.3 ΩZ2=0.2+j0.5 Ω

Q: Problem 3 A 500 KVA, 2300/230 V single phase transformer delivers full rated KVA at 0.85 p.f.…

A: A transformer has specification S=500kVA, V=2300/230V Power is determined by,…

Q: Two single-phase transformers whose phase electrical equivalent circuits are given below are…

Q: A 1-ph transformer 25kVA, 330/110V, 50Hz, Req2 = 0.04522 and Xeq2 = 0.0650 draw the Kapp regulation…

A: Single Phase Transformer: An electrical device that accepts single-phase alternating current and…

Q: A 10kVA 2300/230V 60Hz, single phase transformer has Zp = 5.95 +13.8 ohms and Zs = 0.0595+j0.138…

A: The solution is given below

Q: A 10 KVA, 400 V/200 V single phase transformer with 10% impedance, draws s steady short circuit…

A: Given: A 400 V/200 V single phase transformer with, Power rating, S = 10 kVA Impedance percentage,…

Q: 6. 150 kVA, 2800-240 V, 50 Hz transformer. Reg.Ls = 0.0082N , Xeq.Ls = 0.02230 Step down transformer…

A: Note: We are authorized to answer three subparts at a time since you have not mentioned which part…

Q: Two single-phase transformers A and B are connected in parallel to serve a 600-A single phase load…

Q: Q/ Two transformers A andB of ratings 500 KVA and 250 KVA are supplying a load KVA of 750 at 0.8 Pf…

A: Given- For Transformer A power PA=500 KVA open circuit voltage EA=400 V resistance=1% reactance=5%…

Q: a three-phase step-down transformer with 150 kVA, 2080/208 V 60 Hz Y / Y connected R1 = 0.45 ohm, X1…

Q: A load of 200 kW at 0.85 power factor is to pe shared by two transformers A and B aving the same…

Q: A 60 Hz ideal transformer is rated at 4800/240 V. A load with impedance Z,=12+ j9Q is connected…

A: for a transformer Turns ratio is primary turnssecondary turns=primary voltagesecondary voltage=…

Q: A single-phase transformer 11000/420 V, 50 kVA, 50 Hz has resistance and leakage reactance as…

Q: A 1-ph transformer 25kVA, 330/110V, 50Hz, Req2 = 0.0452 and Xeq2 = 0.06592 draw the Kapp regulation…

A: Single Phase Transformer: A single phase transformer is a transformer that uses only one phase of…

Q: In a 25-kVA, 2000/200 V, single-phase transformer, the iron and full-load copper losses are 350 and…

Q: Q.2) A single phase 440/220V transformer has R=0.150, X=0.80; R.=0.040 and X:=0.80 and supplying a…

A: Given data: V1=440 VV2=220 VR1=0.15 ΩR2=0.04 ΩX1=X2=0.8 ΩP=5 kWpf=0.8Io=6 A

Q: A 150 kVA three phase transformer supplies 100KVA at 50percent lagging power factor. The…

A: Voltage regulation is the change in the secondary terminal voltage of a transformer when full or…

Q: Q2/A/ What are the conditions for satisfving parallel operation of single phase transformer? Deduce…

Q: 6. 150 kVA, 2800-240 V, 50 Hz transformer. Req.Ls Step down transformer delivers 135 kW to a load at…

A: “Since you have posted a question with multiple subparts, we will solve the first three subparts for…

Q: Provide an analysis for the transformer mentioned below. The followings are the reading from the…

A: Note: We are authorized to answer three subparts at a time, since you have not mentioned which part…

Q: (b) The followings are the reading of the test on a transformer. Transformer rating 10 kVA 240/480…

Q: takes 30 A at 200 V the power input being 1,500 W. On open circuit, both transformers give a…

Q: A 4800/240-V, single phase transformer is rated at 10 kVA. It has an equivalent impedance referred…

Q: Consider a 10 KVA, 200/400 V; 50 HZ: single-phase transformer has the following test resalts: O.C.…

Q: A single-phase transformer is rated at 2 kVA, 240/120 V. The transformer is fully loaded by an…

A: The rating of the transformer is given as:

Q: Two 11000/400 V, transformers are operated in parallel to share a load of 250 kVA at 0.85 power…

A: Given data: transformer ratings: 11000/400 V total load : 250 KVA power factor: 0.85 for transformer…

Q: A single-phase transformer 11000/420 V, 50 kVA, 50 Hz has resistance and leakage reactance as…

Q: Q2. Consider the single-phase transformer circuit shown below. Transformer ratings and reactances…

A: We will use following formula of Zp.u to find Zpu on common on common base values Znew (P.u)=…

Q: The equivalent resistance and reactance referred to the secondary side of a 10 kVA, 2200/440 V,…

A: Given here the equivalent resistance and reactance referred to secondary side are 0.3 ohms and 1.2…

Q: Q/ A 600 kVA, 1-ph transformer has an efficiency of 92 % both at full-load and half-load at unity…

A: Given, A 600 KVA ,1-ph transformer has, Efficiency at full load and half load at is 92% and unity…

Q: A single-phase ideal transformer is rated at 1OKVA, 240V/120V. Calculate the following: a. Rated…

Q: 2. Two single-phase transformers A and B are operating in parallel and supplying a common load of…

A: The question is from Transformer. The solution is given below .

Q: Q1. A single-phase transformer rated 1.2kV/120 V, 7.2 kVA yields the following test results;…

Concept explainers

Three-Phase Transformers

Three-segment transformers are a type of transformer used to transform voltages of electrical systems into three ranges. Two type transformers are shell-type transformer and core type transformer. In brief, it could be described because of the exquisite kinds of configurations.

Transformer

Ever since electricity has been created, people have started using it in its entirety. We see many types of Transformers in the neighborhoods. Some are smaller in size and some are very large. They are used according to their requirements. Many of us have seen the electrical transformer but they do not know what work they are engaged in.

Question

Q.2:
Two 2200/110 V, transformers are operated in parallel to share a load of 250 kVA at 0.85
power factor lagging. Transformers are rated as below:
A: 100 kVA; 0.9% resistance and 10% reactance
B: 100 kVA ; 1.0% resistance and 5% reactance
Find the load carried by each transformer.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Three single-phase transformers, each rated 10MVA,66.4/12.5kV,60Hz, with an equivalent series reactance of 0.1 per unit divided equally between primary and secondary, are connected in a three-phase bank. The high-voltage windings are V-connected and their terminals are directly connected to a 115-kV three-phase bus. The secondary terminals are all shorted together. Find the currents entering the high-voltage terminals and leaving the low-voltage terminals if the low-voltage windings are (a) Y-connected and (b) - connected.
A single-phase 100-kVA,2400/240-volt,60-Hz distribution transformer is used as a step-down transformer. The load, which is connected to the 240-volt secondary winding, absorbs 60 kVA at 0.8 power factor lagging and is at 230 volts. Assuming an ideal transformer, calculate the following: (a) primary voltage, (b) load impedance, (c) load impedance referred to the primary, and (d) the real and reactive power supplied to the primary winding.
In developing per-unit equivalent circuits for three-phase transformers. under balanced three-phase operation. (i) A common Sbase is selected for both the H and X terminals. (ii) The ratio of the voltage bases Vbase/VbaseX is selected to be equal to the ratio of the rated line-to-line voltages VratedHLL/VratedXLL. (a) Only one of the above is true. (b) Neither is true. (C) Both statements are true.
What is the nominal transformation ratio of a three-phase Dyn7 transformer consisting of a bank of 110/220 V single-phase transformers? Justify your answer. In addition, sketch how the windings of these transformers can be connected.
Determine the efficiency of three-phase 400 kVA, 11kV/ 380 V transformer at over-loadingcondition by 15% of its rated with unity power factor load. The copper and iron losses atfull load are 16 kW, 4 kW respectively.b) State one or more of the ways to reduce the losses that taken place in transformers.
The efficiency of a 20 kVA 15.4 / 0.4 kV three-phase power transformer is 74,1% for a load with unity power factor at rated power. Relative short circuit voltage% Uk = 30.0 and relative no-load current% I0 = 30. Since the transformer (Star-delta) is connected; Note: In 3-phase electrical machines, the current-voltage information given on the label is always line values. Phase valueWhen given, it must be specified separately. Therefore, all current-voltage information given in the question are line values. 1-) Draw the primary reduced equivalent circuit. 2-) What is the power value measured in the short circuit test of this transformer? 3-) What is the iron loss value of this transformer ?
The following data were obtained from a short-circuit test performed upon a 50 kVA, 2300/115 V, 60 Hz transformer: Esc = 87 V, Isc = 21.75 A, Psc = 590 W. Calculate (a) equivalent resistance, reactance and impedance referred to the primary, and (b) voltage regulation at a power factor of 0.866 lagging. Subject: Electrical Apparatus and Devices
In a three-phase step-down transformer with 150 kVA, 2080/208 V 60 Hz Y / Y connected R1 = 0.45 ohm, X1 = 2.2 ohm, R2 = 4.5 mohm, X2 = 22 mohm, Rc = 10 kohm, Xm = 8 kohms. When installed at 120 kVA, 90 kW back power factor, if the voltage at the load ends is at its nominal value, a) Primary side terminal voltage b) Yield (efficiency) c) Calculate the voltage regulation value?
A 20-ohm resistance is connected across the secondary winding of a single-phase power transformer whose secondary voltage is 150V. Calculate the primary voltage and the turns ratio if the supply current is 5A, neglecting losses.
A network is composed of the utility having Ssc=250MVA, and an 2000KVA transformer, rated at 20KV/400V (no load), whose voltage impedance is 7%, and whose load losses are 15750watts. the short circuit at the secondary of the transformer using the impedance method is: a)27.01KA b)None of these c)25.8KA d)30KA
If the turn ratio of a step-down transformer is 10:1 and the series impedance (referred to the primary) of j50 ohm. If the no-load primary voltage is 230 kV (line-to-line), the secondary side is serving a Y-connected balance load of 1.5+ j0.25 ohms, the reactive power (per phase) absorbed by the load would be?
a 10 KVA, 1940 / 490 V 1-phase transformer with R1=0.35 ohms, R2=0.03 ohms, X1=1.6 ohms and X2=0.06 ohms. Also calculate the equivalent resistance and reactance referred to primary winding.