Two blocks initially at rest, each having a mass of 20 kg, are connected by a string as shown in the figure. The coefficient of sliding friction between the block and the inclined plane is 0.28. The plane is inclined at 350 with the horizontal. The blocks are accelerating at a magnitude of 0.8 m/s2. Assuming the pulleys to be light and frictionless. If the work due to force of friction at B is -105.84 J, find: g. The work done by the Tension at A. h. The work done by the Force of Friction at A. OE A B

Two blocks initially at rest, each having a mass of 20 kg, are connected by a string as shown in the figure. The coefficient of sliding friction between the block and the inclined plane is 0.28. The plane is inclined at 350 with the horizontal. The blocks are accelerating at a magnitude of 0.8 m/s2. Assuming the pulleys to be light and frictionless. If the work due to force of friction at B is -105.84 J, find: g. The work done by the Tension at A. h. The work done by the Force of Friction at A. OE A B

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.78P: The figure shows a steel bar being processed by a rolling mill. Given that P=80kN and r =0.016,...

See similar textbooks

Similar questions

A 3.08-g bullet embeds itself in a 1.7-kg block, which is attached to a spring of force constant 827-N/m. If the maximum compression of the spring is 4.45-cm, find the time of the bullet-block system to come to rest. Provide your final answer in milli seconds.
The tensions of a flat belt are;tight side 500N and slack side 180N.the angular speed N and diameter D of the pulley are 280rev/min and 20cm respectively.if the coefficient of friction between the belt and the pulley 0.6 and the mass m of the belt is 1.2kg/m, including centrifugal tension, Determine; (a) initial tension of the belt (b) angle of lap in degrees (C) power transmitted in the kilowatt (D) maximum power attainable in kilowatt
A person is pushing two boxes placed side by side with each other. What is the acceleration caused by the applied force if the net force is 107.33 N, the coefficient of kinetic friction of the boxes is 0.043 and the sum of the mass of the boxes is 91.5 kg? Is it possible to have one of the boxes generate an applied force of 123.16 N, if yes, what is the mass of the other box?
A force P pulls a series of blocks initially at rest as shown in the figure where all cords are frictionless and incompressible, and all pulleys are frictionless. The 8-kg Block 1 is attached to a 5-kg Block 2. The coefficients of friction between Block 1 and the horizontal surface are 0.38 (static) and 0.27 (kinetic), while between Block 2 and the surface inclined at 28° are 0.40 (static) and 0.31 (kinetic). a. Determine the angle θ at thich Block 1 is being pulled to just get it moving if force P is 71.2 N. b. If the blocks are pulled with a force of 100 N at the same angle, how fast are the blocks moving after 3 seconds? c. What is the total distance travelled?
A 1500-kg automobile traveling along a straight, level road increasesits speed from 54 km/h to 90 km/h in a distance of 100 m. The efficiency of thedrive train is 85%, and the power output of the engine is constant. Determine theoutput horsepower of the engine during the acceleration. Neglect air and rollingresistance.
1) Jonny pulls his sister Jane (weight 28 lbs), who is sitting in a wagon, up an incline ramp (θ = 17°) with a steady speed. If the coefficient of kinetic friction is 0.18, the wagon has a mass of 14 kg, and the length of the ramp is 2.4 m, find: the work done by the frictional force. the work done by the gravitational force.
A pulley system uses a flat belt of cross sectional area 500 mm2 and density 1300 kg/m3. The angle of lap is 165O on the smaller wheel. The coefficient of friction is 0.35. The maximum force allowed in the belt is 600 N. If the the diameter of the smaller wheel is 50 cm and rotates at 3850 rpm , determine Initial tension in the belts and Power transmitted.
A block P of weight 50 N is kept on a plane and now pulled so that the extension in the spring is 10 cm. The stiffness of the spring is 4 N/cm and the coefficient of friction between the block and the plane is μ = 0.3. Find (i) the velocity of the block as the spring returns to its undeformed state and (ii) the maximum compression in the spring. ( By principle of conservation) ( answer= maximum compression is 2.5cm) ( explain with proper steps)
In the system shown in the figure, mA = 2 kg and mB = 5 kg.the mass is connected to each other by rope. A 12 N Fforce is applied to body A at an angle of 10 °.There is only friction between body B and the inclined planeand the kinetic coefficient of friction is 0.3. a) Draw the free body diagram of each object. b) Find the acceleration of the system. g = 9.8 m / s ^ 2, sin (37 °) = cos (53 °) = 0.60, cos (37 °) = sin (53 °) = 0.80, sin (10 °) = 0.17,cos (10 °) = 0.98
200lp box is at rest in the beginning on horizontal surface and force T=100lb and P applied shown. coefficient of static and kinetic friction is us= 0.3 and uk=0.2. find acceleration of block if p=100lb and p=250lb
A man is holding a 2.80-kg ball, as shown in the figure. The distance from the elbow joint to the ball is dball= 32.5 cm, and the distance from the elbow joint to the insertion of the triceps muscle is dM= 2.50cm. The mass of the lower arm, including the hand, is 3.60 kg, and its center of gravity is at a distance dCG= 13.6cm from the elbow joint. 1. Draw a free body diagram of the forearm. 2. What is the magnitude of the force FM, exerted by the triceps? 3. What is the force exerted by the humerus on the elbow joint?
A body Diagram of A nonconducting container filled with 25 kg of water at 20°C is fitted with a stirrer,which is made to turn by gravity acting on a weight of mass 35 kg. The weight fallsslowly through a distance of 5 m in driving the stirrer. Assuming that all work doneon the weight is transferred to the water and that the local acceleration of gravity is9.8 m·s−2, determine:(a) The amount of work done on the water.(b) The internal energy change of the water.(c) The final temperature of the water, for which CP = 4.18 kJ·kg−1·°C−1.(d) The amount of heat that must be removed from the water to return it to its initialtemperature.(e) The total energy change of the universe because of (1) the process of loweringthe weight, (2) the process of cooling the water back to its initial temperature, and(3) both processes together.