Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels co connect and C having a module of 2 mm and those connecting C and B have a module of 3.5 mm. Speed of B is les 1/10th that of A. If the two pinions have each 20 teeth, find suitable number of teeth for the wheels to improv performance of the mechanism, the actual velocity ratio, and corresponding center distance of shafts C and A

Two coaxial shafts A and B are geared together through an intermediate parallel shaft C. The wheels co connect and C having a module of 2 mm and those connecting C and B have a module of 3.5 mm. Speed of B is les 1/10th that of A. If the two pinions have each 20 teeth, find suitable number of teeth for the wheels to improv performance of the mechanism, the actual velocity ratio, and corresponding center distance of shafts C and A

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Two spur wheels with involute teeth gear together externally. The pitch circle diameters are 120 mm and 300 mm and the smaller wheel has 19 teeth. The pressure angle is 20o and the addendum is 0,3 of the circular pitch. Determine 1.1 The length of the arc of approach if the smaller wheel is the driver, and 1.2 The maximum velocity of sliding between the teeth when the driver rotates at 200 r/min
Consider the epicyclic gear system. Set up a tabke of wheel speeds for the cases where all the wheels rotate..Consider the same system with the sun wheel S as the input and the annulus A as the output.The diameters of the sun andbplanet wheels are 150mm and 75mm,respectively. I the sun wheel runs clockwise at 1000 rev/min and output to input ratio Na/Ns is -1,determine the speeds of the arm L and the planet wheel P.
Two cqual involute gear wheels of 40 teeth each, 3 mm module and 20° pressures angleare in mesh. Determine the minimum addendum if 2 pairs of teeth are always in mesh.The gear wheels rotate at 750 r.p.m. and transmit 4.6 kW. Find the normal force at eachpair assuming equal direction of load between the pairs. Neglect friction.
A pickup truck is driving at a speed of 100 km/h on a leveled road. This truck has4 wheels of the same diameter of 400 mm and drives at a gear ratio of 5 to 1 ifits gearbox 5th gear is selected. The gear’s teeth are of involute form with amodule of 8 mm, an addendum is double the module, and the pressure angle isequal to 20° .1.1. If the driving shaft of the front wheels of the truck is connected to the output shaftof the gearbox, determine the number of teeth on the pinion to avoid interferenceand the corresponding number of teeth on the gear wheel.
A simple gear train of 30 and 50 teeth for pinion and gear wheel respectively, is used to drive an electric wheelchair at a velocity that is double the maximum velocity of slip. The pinion has an equal addendum as the gear wheel, a module of 3 mm, and a pressure angle of 14.5o. The wheelchair has a maximum velocity of 5 m/s when its pinion rotates at 800 r.p.m. Calculate The maximum length of a path of the approach in mm.
An inside cylinder locomotive has its cylinder centre lines 1 m apart and has a stroke of 1 m. The rotating masses per cylinder are equivalent to 200 kg at the crank pin, and the reciprocating masses per cylinder to 300 kg. The wheel centre lines are 2 m apart. The cranks are at right angles. The whole of the rotating and 2/3 of the reciprocating masses are to be balanced by masses placed at a radius of 0.8 m. Find the value of variation in tractive effort at 300 rpm. Select one: A. ±58476 N B. ±69780 N C. ±79654 N D. ±12475 N
A compound epicyclic gear is shown in Fig. for Q.2. C and D form acompound wheel which rotates freely on shaft G. The planet wheels B andE rotate on pins fixed in arms attached to shaft G. C and F have internalteeth: the others have external teeth with the following numbers: A, 40;B, 30; D, 50; E, 20. If A rotates at 500 rev/min and wheel F is fixed,find the speed of shaft G.
The number of teeth on the driving sprocket chain is 50, used to change up of speed from 500 r.p.m. to 850 r.p.m. Find the number of teeth on the driven sprocket. If the pitch circle diameter of the driven sprocket is 350 mm and center to center distance between the two sprockets is 1000 mm, determine the pitch and length of the chain.
A chain with speed of 900 fpm has driving sprocket turns at 1000 rpm. If the pitch of chain is 3/4-in, find the number of teeth of driving sprocket. (Ans. 14 teeth)
A pair of gears, having 40 and 30 teeth respectively, are of 25° involute form. Theaddendum length is 5 mm and the module is 5.5 mm. If smaller wheel is the driver androtates at 1500 r.p.m. find the velocity of sliding at the point of engagement and at thepoint of disengagement.
Two mating spur gear with module pitch of 6.5 mm have 19 ad 47 teeth of 20° pressure angle and 6.5 mm addendum. Determine the number of pair of teeth and angle turned through by the larger wheel for one pair of teeth in contact. Determine also the sliding velocity at the instant engagement commences engagement terminates. When the pitch line velocity is 1.2 m/s. b.) The number of teeth on each of the two spur gears in mesh is 40. The teeth have 20° involute profile and the module is 6mm. If the arc of contact is 1.75 times the circular pitch. Find the addendum.
Two mating involute spur gears of 20 pressure angle have a gear ratio of 2. The number of teeth on the pinion is 20 and its speed is 250 r.p.m. The module pitch of teeth is 10 mm. If the addendum on each wheel is such that the path of approach and the path of recess on each side are half the maximum possible length cach, find: i) the addendum for pinion and gear wheel, i) the length of arc of contact, iiithe maximum velocity of sliding during approach and recess. Assume pinion to be driver.