Two forces X and Y act vertically downward directly at points D and F respectively while force Z acts at point B as shown. Determine the magnitude (N) of the force in member GF if X=754N, Y=415N, Z=172, a=3.5m and b=3.4m. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate C if force is compressive or T if tensile. X Y ... A b H G FbE a вь с Ь D

Two forces X and Y act vertically downward directly at points D and F respectively while force Z acts at point B as shown. Determine the magnitude (N) of the force in member GF if X=754N, Y=415N, Z=172, a=3.5m and b=3.4m. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate C if force is compressive or T if tensile. X Y ... A b H G FbE a вь с Ь D

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter6: Beams And Cables

Section: Chapter Questions

Problem 6.65P: Cable AB supports the uniformly distributed load of 4 kN/m. If the slope of the cable at A is zero,...

See similar textbooks

Similar questions

Two forces X and Y act vertically downward directly at points D and F respectively while force Z acts at point B as shown. Determine the magnitude (N) of the force in member GF if X=649N, Y=454N, Z=115, a=5m and b=3.8m. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate C if force is compressive or T if tensile.
Two forces X and Y act vertically downward directly at points D and F respectively while force Z acts at point B as shown. Determine the magnitude (N) of the force in member CD if X=593N, Y=238N, Z=158, a=3m and b=3.4m. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate C if force is compressive or T if tensile.
Determine the magnitude(lb) of the vertical component of force at point C if P = 127 lb, x= 13.9 in, y = 8.7 in, and z = 8.2 in. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction: use U if upward and D if downward
Determine the magnitude (lb) of the horizontal component of force at point C if P = 130.9 lb, x = 14.3 in, y = 7.4 in, and z = 6.8 in. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate the direction: use L if to the left or R if to the right.
Determine the magnitude of force (kN) in member AB if F=76532 N , a=2.93m , b=1.42m and c=4.16m. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate C if force is compressive or T if tensile.
Determine the magnitude of the force (lb) in member CD of the truss shown if P = 34150 b, Q = 33650 b, and y = 7.2 ft. Round off only on the final answer expressed in 3 decimal places, Instead of units, indicate whether the force is tensile or compressive: use Tif tensile and C if compressive.
For the truss structure below, if the maximum force that any member can support is 18 kN in tension or 11 kN in compression, determine the maximum force P that can be supported at joint A. Answer must have 1 number past the decimal point and have the proper units.
Determine the magnitude of the force (lb) in member CD of the truss shown if P = 30599 lb, Q = 35388 lb, and y = 7.4 ft. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate whether the force is tensile or compressive: use T if tensile and C if compressive.
Given: F1=5 kN F2=12 kN F3=4 kN F4= 11 kN L=8 m Determine the force in member CF by the method of sections.
Determine the magnitude of force (kN) in member BC if F=73323 N, a=3.33m, b=1.14m and c=5.69m. Round off only on the final answer expressed in 3 decimal places. Instead of units, indicate C if force is compressive or Tif tensile.
Determine the normal tension of the cylinder piston rod (diameter 32mm). The clamping force of the pliers is 6000N. The dimensions of the structure are: x1 = 10 mm x2 = 120 mm y1 = 110 mmy2 = 798 mm Use the units [N, mm], ie the answer comes in MPa !!! Please enter a numeric value only !!
Two forces X and Y act vertically downward directly at points D and F respectively while force Z acts at point B as shown. Determine the magnitude of the force in member GF and EF if X=420N, Y=300N, Z=100, a=4.5m and b=3.5m. Instead of units, indicate C if force is compressive or T if tensile.