Two ideal gases were delivered to two containers of equal volumes temperature and pressure. One of the containers has a fixed volume, while the other is a cylinder equipped with a weightless piece of furniture. initially the pressure of gas equals blood pressure. Then the gases are heated with a Bunsen burner. Draw a picture to represent the processes described and determine what are the signs of q and w of the gases under these conditions? will exist difference in the internal energy of these systems? your job.

Two ideal gases were delivered to two containers of equal volumes temperature and pressure. One of the containers has a fixed volume, while the other is a cylinder equipped with a weightless piece of furniture. initially the pressure of gas equals blood pressure. Then the gases are heated with a Bunsen burner. Draw a picture to represent the processes described and determine what are the signs of q and w of the gases under these conditions? will exist difference in the internal energy of these systems? your job.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter1: Basic Modes Of Heat Transfer

Section: Chapter Questions

Problem 1.82P: Discuss the modes of heat transfer that determine the equilibrium temperature of the space shuttle...

See similar textbooks

Similar questions

Question #1 a) The absolute pressure inside a tank is 0.13bar, and the surrounding atmospheric pressure is 98 kPa. A Bourdon gage is mounted in the tank wall to measure the pressure, in kPa? Is this a vacuum or gage reading? b) (967)kJ of heat is transferred from the system to the surroundings when a closed system of mass (28)kg undergoes a process. During the process, 200kJ work is done on the system. If the initial specific internal energy of the system is 300 kJ/kg, Describe the process and determine the final specific internal energy, in kJ/kg? Neglect changes in kinetic and potential energy.
A series of pistons / cylinders positioned horizontally within a constant- temperature bath. The piston can move in the cylinder without friction. There is a force outside which holds the piston in position, against the initial gas pressure equal to 14 bar. The volume of gas is initially 0.03 m3 . External force acting on the piston reduced gradually, and the gas is isothermal expansion until the volume is doubled. If the relationship between gas volume and pressure can be stated by: PVt = constant How much work did the gas do at the time of expansion? How much work is that will be carried by the gas if the external force is reduced suddenly to the force they will be half of the original force.
The fluid is heated from 125 degrees Fahrenheit to 225 degrees Fahrenheit. Consider an ideal gas with the following characteristics: R = 85 ft-lbf/lbm-R Cp = 0.35 + 0.000325T BTU/lbm-R If the heating is at constant pressure, (e) the value of k at 160 degrees Celsius. If the fluid undergoes an isentropic process, determine (f) non-flow work and (g) steady-flow work. (For item f and g, use the value of k at 160 degrees Celsius).
2. A frictionless piston–cylinder device and a rigid tank contain 2 kmol of an ideal gas at the same temperature, pressure, and volume. Now heat is transferred, and the temperature of both systems is raised by 10°C. Solve for the amount of extra heat that must be supplied to the gas in the cylinder that is maintained at constant pressure. (3 DECIMAL IN FINAL ANSWER PLS)
Task 5A sample of gas is compressed by an average pressure of 2 atm which decrease its volume from400 cm 3to 200 cm 3. During the process, 10 J of heat is rejected to the surroundings. Explain and demonstrate the application of the first law of thermodynamics to this system and calculatethe change in energy of the system.
Five kilograms of water at 35 degrees Celsius are placed in a piston under 5.335MPa (State 1). Heat is added to the water at constant pressure until the piston reaches a stop at a total volume of 0.035 m3 (State 2). Most heat is added at constant volume until the temperature of water reaches 322 degrees Celsius (State 3). Determine (a) the quality of fluid and the mass of the vapor at State 2, and (b) the pressure of the fluid at State 3.
Suppose you have two kettles --a plug-in electric kettle and a stovetop kettle. The electric kettle uses electricity from a natural gas fired powerplant, while you boil water in your stovetop kettle on a natural gas burner. Based on the following information, which of these kettles demonstrates a higher energy efficiency? Please calculate the efficiencies of each kettle and express answers as percentages -The natural gas power plant converts chemical energy of the natural gas to electrical energy with 58% efficiency. -High-voltage power lines from the power plant to your house convey electricity with 92% efficiency. -The electric kettle converts electrical energy to thermal energy in the water with 85% efficiency. -The stove burner converts chemical energy of natural gas to thermal energy with 98% efficiency (the other 2% is light). -The stovetop kettle transfers 35% of the stove’s thermal energy to the water in the kettle.
Helium gas initially has a volume of 50 liters, a pressure of 2 x 10⁵ N/m², and a temperature of 300 K. Then the gas undergoes a process at constant temperature until the volume increases to 100 liters. If In 2 = 0.693; specify: a. pressure after the volume increases
Air in a cylinder-piston system expands and works on the piston. The temperature of the air decreases during the process from the initial temperature of (30×1.6)°C down to the final temperature of 20°C. Specific heat values of air at constant pressure and constant volume are 1,000 J/kg.K and 730 J/kg.K respectively. (a) Determine the change of enthalpy per mass and the change of internal energy per mass, respectively. (b) This process produces 20 kJ/kg of work. Combine this number with your outcome from (a), to estimate the amount of heat transfer per mass required for this process to happen.c) Based on the outcome from part (b), determine whether the heat went ‘into’ the system or ‘out of’ the system.
Air is contained in a piston cylinder arrangement as shown in Fig.(Refer attachment). The piston can be assumed to be massless, frictionless, and perfectly insulated. 10 kg of dry ice (solid CO2) is placed on top of the piston. The initial conditions for air inside the cylinder are P1=121 kPa, T1= 300 K. Dry ice sublimates gradually, and its mass reduces to 5 kg. Ambient air is always at room temperature (27oC) and atmospheric pressure. (Given: R=287 J/kg ·K, g = 9.8 m/s2, CP/CV for air = 1.4; Neglect all heat transfer to the dry ice block.) a)Assuming the cylinder to be perfectly insulated, calculate the specific work done for the process. b)Assuming the cylinder to be perfectly conducting, what is the heat required per unit mass of air to complete the process? c) Plot the processes described in (a) and (b) together on a P-V diagram. From this plot, which process appears to have more work? Explain.
Oxygen (molar mass 32 kg/kmol ) expands reversibly in a cylinder behind a piston at a constant pressure of 3.129 bar. The volume initially is 0.011 m3 and finally is 0.0327 m3; the initial temperature is 16.3 0C. Calculate the heat supplied during the expansion in the correct unit to two decimal places. Assume oxygen to be a perfect gas and take the specific heat at constant pressure as = 0.917 k J / k g K and molar gas constant as = 8,314 J / kmol K
Calculate the amount of work necessary for the reversible compression of steam from 1 bar to 10 bar. The compression is to take place in a cylinder fitted with a weightless piston at the constant temperature of 500 oC. Under these conditions we have a superheated vapor. Report your answer in units of kJ/kg using three decimal places. As you check your work, note that here we have compression from 1 bar to 10 bar under constant temperature. We would expect the volume of the system to decrease. Use this to check the sign (positive or negative) of your computed work.