Two identical rods AB and BC form an L-shaped assembly. The assembly is pressed against a spring at D and released from the shown position. Knowing that the maximum angle of rotation in its subsequent motion is 60° with the horizontal (counterclockwise), Find the angle rod AB forms with the horizontal (degrees) when the angular velocity reaches 7 rads/sec. 0.4 m

Two identical rods AB and BC form an L-shaped assembly. The assembly is pressed against a spring at D and released from the shown position. Knowing that the maximum angle of rotation in its subsequent motion is 60° with the horizontal (counterclockwise), Find the angle rod AB forms with the horizontal (degrees) when the angular velocity reaches 7 rads/sec. 0.4 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A man pays P 114,100 every end of the quarter for a car bought on installment terms. If the man wishes to pay every end of the month instead of every end of the quarter, how much should he pay if the interest is 12% compounded monthly? pls answer 10 mins deadline
The farmer wanted to know the number of hills per hectare in his rice production, if row is 15 cm apart and the hills is 15 cm apart.
A circular saw blade 0.6 m in diameter starts from rest and accelerates with constant acceleration to an angular velocity of 100 rad.s-1 in 20 s. Find the angle in degrees through which the blade has turned in the 20-s interval
A circular saw blade 0.6 m in diameter starts from rest and accelerates with constant acceleration to an angular velocity of 100 rad.s-1 in 20 s. Find the linear velocity of a point in the rim of the saw when the angular velocity is 10 rad.s-1.
An engine has four cylinders of 68 mm bore and 75 mm stroke. The cubic capacity of the engine is (a) 1089.5cm³ (b) 1489.5m³ (C) 1289.5cm³ (d) 1689.5cm³
Answer this ASAP Two points P and Q lie on a radial line of a plate rotating at a fixed center. The points are 20 cm apart. The velocity of point P = 100 cm/s, and the velocity of point C = 150 cm/s. Determine the radius of rotation of each point.
32 - If the velocity of water flowing through a pipe with a diameter of 134 mm is 1.89 m/s, which of the following is the volumetric flow of water? a) 0.01664 m³/h B) 0.02891 m³/h NS) 0.01895 m³/h D) 0.02665 m³/s TO) 0.02389 m³/s
Find ? and ?.
Five engineers measure the thickness of a slab using a meter stick and a vernier caliper. One engineer got a thickness of 4.3 cm ± 0.1 cm using a meter stick, the other four engineers measured a thickness of (a) 4.32 cm ± 0.01 cm, (b) 4.31 cm ± 0.01 cm, (c) 4.24 cm ± 0.01 cm, and (d) 4.43 cm ± 0.01 cm respectively using the caliper. Which of these four measurements made by the four engineers agree with the measurement obtained by the engineer that used a meter stick? Only a (b) and (c) (c) and (d) (a), (b), and (c) none of these
MECHANICAL ENGINEERING UPVOTE WILL BE GIVEN. PLEASE WRITE THE COMPLETE SOLUTIONS LEGIBLY. SHOW THE STEP-BY-STEP PROCESS WITH SHORT COMMENT/EXPLANATION. ANSWER IN 4 DECIMAL PLACES. Two gaseous streams containing the same fluid enters a mixing chamber and leaves as a single stream. For the first gas the entrance conditions are A1=500 cm², v1=230 m/s, p1=1.60 kg/m³. For the second gas the entrance conditions are A2= 300 cm³, m2=8.84 kg/s, v2=0.502 m³/kg. The exit stream conditions is v3=130 m/s and v3=0.437 m3/kg. Determine the following: (a) the total mass flow leaving the chamber (kg/sec) (b) the velocity of the gas at 2. (m/sec)
In the process of cutting a metal piece to obtained chips, a cutting force of 100 N, a tangential force of 120 N, and a rake angle of 250 are applied. Use a scale and protractor, to measure off distances (forces) [R-resultant force, F-friction force and N-normal force], and friction angle.
For this problem, Block D v =16 cm / s to the left & a = 30 cm/ (s ^2) to the right in the indicated position. Find the v and a of block A for this position.