Two loads P1 and P2 resting on two inclined plane and connected by a horizontal chord AB as shown in figure. If P2 = 1200 kN determine the maximum and minimum value of P1 and tension in chord AB so that the static equilibrium exist the angle of limiting friction is 23o at all rubbing surfaces.

Q: 2. Considera the figure below, the rigid bar to which the two springs are connected remains…

A:

Q: 7. In the wedge shown in the figure. Determine the largest angle that will cause the wedge to be…

A: As per given question  We have to determine the largest angle

Q: Problem 2. Considering a 20 kg bar as shown in the figure: a) find angle theta and the reactions to…

A: Consider NA as the reaction at point A, NB as the reaction at point B, fB be the frictional force…

Q: The bar DBC is supported by a roller at D (on a smooth slot), a bar AB, and the spring at C, which…

A: The roller gives a horizontal reaction Dx at D. The hinge gives a horizontal reaction Ax and…

Q: In the figure shown, the rigid bar with negligible mass was horizontal before the load P was…

A:

Q: Q7. For the pulleys system in figure, determine the force P to maintain equilibrium, the weight of…

A:

Q: Activity 2. In the figure, the coefficients of friction are as follows: 0.25 between blocks, 0.20 at…

A:

Q: The horizontal force acts on the structure in the figure below. Find the effect of the reaction at…

A:

Q: Suppose that a traction on the foot maintained shown in the figure below. Draw the free body diagram…

A:

Q: 70 in - 36 in - y 20 in 3300 lb

A: 1) As given in question rear wheels are locked and front are free to turn so we can consider front…

Q: D F 4m E 3m 3m he pin-jointed frame work in the figure If a vertical concentrated load of 800KN…

A:

Q: Q.4 A body A weighing P, descends down an inclined plane D which makes an angle a with the…

A: Solution::

Q: |Can the system in Figure (4) be in static equilibrium in the position shown? The uniform bar AB…

A:

Q: Determine the coordinates of D in the YZ plane so that the force in CD will be a minimum.

A:

Q: Problem No. 2 The structure shown is hinged at A and C. Find the horizontal and vertical components…

A:

Q: One end of a unifom rod of length L = 4 m and a mass of 2 kg is connected by a rope. The other end…

A:

Q: The slender plank shown in figure is held in equilibrium by the action of the force Fp. Find the…

A: Given, m = 200 kg

Q: The boom AB supports a load of W = 720 lb. The boom is supported by a ball-and-socket joint at A and…

A:

Q: The force induced in member Q.3) PQ due to load W in figure will be

A:

Q: Q: The two-steel shaft shown in figure have the same diameter and weight 120 lb each. Neglect the…

A:

Q: 4 - For the given frame and loading, find the reactions at supports A and E. The pin and slot…

A: Draw the free-body diagram of the beam.

Q: A 7-ft boom is held by a ball and socket at A and by two cables EBFand DC; cable EBFpasses around a…

A: Given: The length of boom, L = 7 ft The force acting at C, P = 390 lb

Q: Q The two-steel shaft shown in figure have the same diameter and weight 170 lb cach. Neglect the…

A:

Q: B) : A slider crank mechanism shown in figure, If the net piston effort Fp=900 N, determine 1. Force…

A:

Q: In Fig. , a cable is attached to the structure at E, passes around the 2-ft-diameter, frictionless…

A: Draw the free body diagram for the complete problem. Now determine the moment about point G  and…

Q: 6. The upper jaw D of the toggle press slides with negligible frictional resistance along the fixed…

A:

Q: Q6: A 60 kg cupboard is to be shifted to the right, p, between cupboard and floor is 0.35 as shown…

A:

Q: A uniform bar AB weighing 500KN, is fastened bya frictionless pinto a block weighing 100kN as shown…

A:

Q: b) For the truss in the figure below, determine the zero-force members and give a short explanation…

A:

Q: Q The two-steel shaft shown in figure have the same diameter and weight 120 lb each. Neglect the…

A:

Q: A uniform rod of weight mg and length L is in equilibrium on a frictionless support as shown in the…

A:

Q: Q The two-steel shaft shown in figure have the same diameter and weight 170 lb each. Neglect the…

A:

Q: Bar AB of Fig. with weight W and length L has a uniform cross section. Rotation of the bar is…

A:

Q: Q.1) For the following space truss where F1 = {300i + 400j -500k}, F2 = {600j}: (a) Find the force…

A:

Q: P = 100 lb. Problem 2 – A concentrated load P = G 100 lb. acts at point G. All slots are…

A: Replacing supports and slotted links by reactions as shown in the figure below.   The tension and…

Q: A uniform stone slab weighs 400 lb and is suspended by 3 cables and subjected to a downward vertical…

A:

Q: Determine the reaction between the wall and B in kN.

A: Given: TO determine: The reaction between the cylinder B and wall

Q: The bar AB in figure "a" has weight W, length L, and is articulated at point B. End A is supported…

A:

Q: From the figure, the load at G is 12 kN: To determine: a) Piston force JL b) Pin force E and M c)…

A: Draw FBD of GEM and calculate pin forces at E and M:

Q: The simplest truss consists of two rods and is loaded by the force F. Given: F = 5,1 kN. Angle α =…

A:

Q: mb: L d- ms A horizontal L=1.2 m long mb=12 kg uniform bar is hinged on the left end and pulled at…

A:

Q: The system shown is composed of an ABG bar, supported by a pin at point A and by a collar smooth at…

A:

Q: Q The two-steel shaft shown in figure have the same diameter and weight 150 lb cach. Neglect the…

A:

Q: A ladder with a length of L= 8 m and a mass of M=50 kg rests on a rough ground (providing friction)…

A: Part a) The mass of the ladder is given as m=50 kg. Since, the weight is defined as the product mass…

Q: Calculate the Reactions for each lettered problem. Detailed Steps

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: ABC is a rigid bar, with a pin at B, and cable ADC wound around the pulley at D. There is a force of…

A:

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.