S:13) Quèstion 11Two Standard Inverse relays with following settings:Ipu1 = 200 PS% = 100 CT = 200:5 TMS1 = 0.1 t1 = 0.3Ipu2 = 250 PS% = 250 CT = 200:5If the Fault current is 16,448 and the CTI is 0.4,Calculate the value of TMS2.

The operating time of Relay 1 is given as 0.1s. CTI is the coordination time interval or the time…

Two Standard Inverse relays with following settings: Ipu1 = 200 PS% = 100 CT = 200:5 TMS1 = 0.1 tí = 0.3 Ipu2 = 250 PS% = 250 CT = 200:5 If the Fault current is 16,448 and the CTI is 0.4, Calculate the value of TMS2.

Two Standard Inverse relays with following settings: Ipu1 = 200 PS% = 100 CT = 200:5 TMS1 = 0.1 tí = 0.3 Ipu2 = 250 PS% = 250 CT = 200:5 If the Fault current is 16,448 and the CTI is 0.4, Calculate the value of TMS2.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter9: Unsymmetrical Faults

Section: Chapter Questions

Problem 9.63P

See similar textbooks

Related questions

Q: 2. An over current relay set to operate at 10 A is connected to the CT as shown, with a 200: 5 CT.…

Q: c. Current transformers, of turns ratio 1200:1, are used as supply to a differential relay of…

A: Given: Turns ratio=1200:1RL=1.8+2.5RL=4.3ΩSetting current, Is=1.5 AI=80 kARelay resistance,…

Q: A three-phase power system consists of a synchronous machine connected through a lossless…

A: Given Maximum power transfer when there is no fault is 5 pu and the power transfer is 2.5 pu. The…

Q: "In back up protection scheme of power system a 5-Amp, 4-second overcurrent relay having a current…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: Current setting of a relay is used to set the operating time of relay during fault condition O True…

A: Current setting of relay is used to set the operating time of relay during fault condition? True…

Q: Complete the blank For a 66 kV transmission, the number of suspension insulators required is…

A: Each disk of suspension type insulator is designed for 11KV no of insulator disk n=line…

Q: (b) An 11 kV, 50 Hz radial system is shown in Figure 6. Assume a CO-7 overcurrent protective relay…

A: Given: An 11 kV, 50 Hz radial system is shown in the figure below: Assume a CO-7 overcurrent…

Q: "In back up protection scheme of power system a 5-Amp, 4-second overcurrent relay having a current…

A: We are authorized to answer three subparts at a time, since you have not mentioned which part you…

Q: X4 3 X3 XG1 1 (F) X2 X5 Figure 1 Table 1 Component Reactance (pu) X1 0.1 X2 0.2 X3 0.3 X4 0.4 X5 0.5…

A: In this question we need to find a short circuit capacity for the given system. We replace the given…

Q: i) Design appropriate CT ratios for CTA, CTB, and CTC. (ii) Estimate time of Operation for all three…

A: Dear student you asked to solve the question with multiple sub part.we have limited time for solve…

Q: A 50 element is set for 0.8 per unit (80%) of the CT primary current rating. For a CT with a rated…

Q: For the system shown below (bus protection by differential current relay) ii an external fault has…

A: (ii) For external fault, zero current will flow through the operating coil of the relay. From the…

Q: A generator rated 100 MVA, 20 kV has X1=X2=20% and X0 =5% Its neutral is grounded through reactor of…

Q: In the following power system, overcurrent relay R₁2 is to provide primary protection to line 1-2…

A: A relay is a protective device used for overcurrent protection it consists of a coil and magnet…

Q: By using normal operating conditions in a short span. the system can be restored to O High speed…

A: By using High speed Restoring fuse the system can be restored to normal operating condition in a…

Q: в A 1Ω 10Ω 100 V Figure 4.20 System diagram for Problem 4.2a в A 10Ω 1Ω 100 V Figure 4.21 System…

A: Part(a) Fig: Given circuit diagram When fault occurs at bus A it causes short circuit on the bus…

Q: Ex.2: Determine the time of operation of an IDMTL relay rating 5A, 2.2sec and having a plug setting…

A: The solution can be achieved as follows.

Q: Voltage and current are the restraining and operating quantity for a simple impedance relay O True O…

A: The impedance relay measures the fault impedance distance from the position relay. In case the…

Q: Determine the time of operation of a 5-ampere, 3-second over current relay having a current setting…

Q: The using of relay is * Break the fault current O Sense the fault Sense the fault and direct to trip…

A: Current transformer is used to step down high current and then the output is feed to relay.

Q: Two relays R1 and R2 are connected in two sections of a feeder as shown in Figure Q2. Relay R1: CT…

A: Given information: Relay R1: CT ratio=300/5, plug setting=2.5 A, TMS=0.3. Relay R2 : CT ratio=500/5,…

Q: A 50 MVA, 3 phase, 33 kV synchronous generator is protected by the Merz-Price protection using…

A: Given Data, VL = 33 KV CT ratio 10005 Resistance (R) = 7.5 ohms And we have been asked to find the…

Q: 25 MVA 13.8 kV generator with X"d=15% is connected through a transformer to a bus which supplies…

A: Fault currents that are symmetrical and asymmetrical. The system/synchronous machine's reactance is…

Q: An IDMT type over-current relay is used to protect a feeder through 5000/1 ACT. The relay has a PS…

A: We got an over current relay of IDMT type. CT ratio = 5000/1 Current Setting = 125 % Time Setting…

Q: A 60 MVA, 3 phase, 11 kV synchronous generator is protected by the Merz-Price protection using 1000/…

Q: The current rating of an over current relay is 5 A. The relay has a plug setting of 150 % and time…

Q: B-For the radial shown in the figure below, calculate: 1- the fault currents for the faults.: FA and…

Q: A 25 MVA, 11 kV, 3-phase, 60 Hz, generator has its neutral grounded through a 4% reactor. It is…

A: Given X1=20% X2=20% Xg0=8% Xn=4% MVA rating of generator=25 MVA Voltage rating =11kV

Q: 10. In high-voltage switch gear, the irsulation used inside the breaker (arc chambers) is (a) Epoxy…

A: In high voltage switch gears, the insulation used in the arc chamber is generally epoxy raisins.

Q: Q2:- Two 50 MVA, 11kV synchronous generators are connected to common bus bar which supplies a…

A: As per Bartleby policy we can answer only one question at a time. Please repost for other. Select…

Q: A 400KV single busbar substation with 4 outgoing feeders is protected by a high impedance…

A: Substation and its equipment's The single line diagram is the basic set of diagrams that is where…

Q: If the fault current is 2 kA, the relay setting is 50 % and the CT ratio is 400/5, then what is the…

A: Given: fault current=2 kARelay setting=50 %CT Ratio=400/5

Q: alculate the operation time of an overcurrent relay of (10 A, 3 seconds) that has a current setting…

Q: A radial feeder ABC is sectionlized into parts AB and BC. Part AB near the source, has a relay R1.…

Q: The current rating of a relay is 5A, PSM= 1.5, TMS=0.4, CT ratio = 400/5, fault current is 600A.…

Q: Given a 3-Ampere, 5-second overcurrent relay having a current setting of 150% and a time setting…

A: According to the question we have to determine its time of operation

Q: NEC 110.9 states that equipment intended to interrupt current at_levels should have an interrupting…

A: Consider the circuit breaker that has the rating of 300 A. Consider the current of 9500 A is the…

Q: The tap changer with inductive type of impedance uses high speed switching False True Earth relays…

A: 1. The tap changer with inductive type of impedance uses high speed switching. True or False Given…

Q: Based on the following figure, which below statement is WRONG? mo amimo Of R₁ R₂ a) Relays R1 and R6…

A: Overcurrent relay: Relay is used to detect the fault and send the signal to the circuit breaker to…

Q: Q2:- Two 50 MVA, 11kV synchronous generators are connected to common bus bar which supplies a…

Q: Problem-2 A star-connected, 3-phase, 10 MVA, 6.6 kV alternator is protected by a differential…

A: Current transformer is used for two purpose in Power system. As a Measuring instruments As a…

Q: Three phase CT connections for 5 amp overcurrent relay & earth fault relay having an almost constant…

A: The solution is given below

Q: (b) A 30000 kVA, 13.8 kV generator with X = 18% is connected to a bus which supplies two identical…

A: Generator data Sb= 30000 kVA Vb=13.8 kV Xd'' =18 % Motor data Vb= 7 kV Sb=6000 kVA Xd'' =25 %

Q: Problem-2 A star-connected, 3-phase, 10 MVA, 6.6 kV alternator is protected by a differential…

A: In this question we need to find a % of stator winding are unprotected.

Q: The current rating of an over current relay is 5 A. The relay has a plug setting of 150 % and time…

Q: An IDMT type over-current relay is used to protect a feeder through 5000/1 ACT. The relay has a PS…

A: We have an IDMT type over-current relay. Given data, CT ratio = 5000 / 1 Plug setting = 125 %…

Q: (1.) b) E/(Z° +Z' +Zu² +3Z,) d) E/(Zu² +Z,) In short circuit studies, the positive sequence current…

Question

S:13)

Quèstion 11
Two Standard Inverse relays with following settings:
Ipu1 = 200 PS% = 100 CT = 200:5 TMS1 = 0.1 t1 = 0.3
Ipu2 = 250 PS% = 250 CT = 200:5
If the Fault current is 16,448 and the CTI is 0.4,
Calculate the value of TMS2.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

CT secondary current of Relay 2 during fault

VIEW

Calculating PSM for Relay 2

VIEW

Calculating TMS of Relay 2

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

An over-current relay has a Time Multiplier Setting of 0.4 is required to work in 1.2sec, and is connected in a circuit through a CT having a ratio of 400/4. What should be the current setting assuming a fault current of 2000A
asnwers: 1) relay at C (CT ratio) = 40 : 1 relay at B (CT ratio) = 60 : 1 relay at A (CT ratio) = 40 : 1 2) TMS/A = 0.711 3) top = 1.48 sec ( relay will operate as per the fault current level.) i) Design appropriate CT ratios for CTA, CTB, and CTC. (ii) Estimate time of Operation for all three relays for maximum value of fault current to maintain the selectivity. (iii) Determine TSM for relays at bus A and B for maximum fault current. (Use the standard formula for IDMT relays for these calculations.) (iv) Also use the standard curves for IDMT relays shown in Figure 2 to select TSM for relays at bus A and B for maximum fault current. Compare results obtained in (ii) and (iv). Verify the design to ensure that selectivity is maintained at minimum fault current for the fault in the same zone
A 50 element is set for 0.8 per unit (80%) of the CT primary current rating. For a CT with a rated 4A secondary, this would require a test current of ____ to be injected into the relay. ..
Given a 3-Ampere, 5-second overcurrent relay having a current setting of 150% and a time setting multiplier of 0.4 connected to the supply circuit through a 300/2 current transformer, a 3500 A fault current was carried through the circuit. Determine its time of operation
True or false 1. Three phase fault is the most commonly occurring fault than other types of faults. 2. The range of generator rotor angle for stable operation is 0°< s < 180°. 3. The infinite bus in power system is a large system with infinite voltage. 4. At value of (s= 90°) the maximum power transfer takes place. 5. Per unit system (PU) is a ratio of actual value in any units to the base or reference value in the same units.
Q/ Calculate the operation time of an overcurrent relay of (10 A, 3 seconds) that has a current setting of 1. The time setting multiplier is 60 %, which supplies a current through (200/ 2.5) CT (current transformer) at a fault current of 1000 A. Re-solve the problem if the time setting multiplier is 50 %. How do you explain the difference?
An REJ525 relay with a 5 A rated current is connected through a CT with a ratio of 129 to a primary line. If the line current is 8,751 A or higher, the relay must be tripped in 0.08 seconds. Calculate I>> in per unit.
4. A 25 MVA, 11 kV, 3-phase, 60 Hz, generator has its neutral grounded through a 4% reactor. It is having isolated neutral. Each generator has X 1 = 20%, X 2 = 20% and X go = 8%. If a single line-to-ground fault occurs at the common busbars with the generators unloaded at rated voltage, thefault current will be
24. Which of the following is not one of the technical reasons for grounding the starpoint ? a) Preventing dangerous voltage peaks in solid phases of faults arising against the earth in the form of an arc b) Limiting inductive interference between power and communication circuits C) Limiting potential drift in low voltage windings d) Limiting the earth fault current e) Providing potential drift
As illustrated in your reading material, the plug-in busway for motor Branch circuits has tap- off openings every_inches. A. 6 b. 10 c. 12 d.16
Specify and select a circuit breaker for installation at a 20 000 V substation where the 3-phase fault level is 150 MVA, X = 2.67Ω, R = 0.13 Ω and C = 5 000 pF. A circuit breaker with 36 000 V rated maximum voltage, 6 kA rated short-circuit current, 2.15 rated voltage range factor and rated rate of rise of recovery voltage (RRRV) of 2.26 kV/μs is available in stock.
A generator is protected by restricted earth fault protection. The generat ratings are 13.5kV, 10 MVA. The percentage of winding protected against phase to ground fault is 85%. The relay setting is such that it trips for 20% out of balan Calculate the resistance to be added in the neutral to ground connection.