2 Two wooden members of uniform rectangular cross section are joined by the simple glued scarf splice shown. Knowing that P= 18 kN,determine the normal and shearing stresses in the glued splice.75150 mm45°The normal stress iskPa.The shearing stress iskPa.

Answered: Image /qna-images/answer/f39c470e-7695-4c4a-a93a-d4be9551fa30.jpg

Answered: Two wooden members of uniform…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rectangular bar has a width of w = 3.25 in. and a thickness of t = 2.00 in. The normal stress on plane AB of the rectangular block shown is 6 ksi (C) when the load P is applied. Assume a = 4 and b = 5. Determine the maximum shear stress in the block at any possible orientation. Express your answer in ksi rounded to the nearest hundredths.
a signage is connected to a pole as shown in the figure. if the pole is a hollow shaft with ouside and inner diameter s 100mm and 70mm respectively. A wind pressure of 2kN/m^2 is acting on the signage . Given a= 200mm b=2m c=1m d=4m. 1. Determine the shearing stress (Mpa) at the base of the pole. a.1.25 b.1.96 c 2.1 d1.5 2.Determine the maximum bending stress (MPa) in the hollow shaft. a.248.28 b.241.28 c.255.23 d.312.54 3. Determine the torsional shearing stress (MPa) a.25.05 b 18.59 c.34.85 d.32.17 Answer. 1.96,241.28,32.17
A simply supported wood beam with overhang is subjected to uniformly distributed load q. * Inserted Photo * The beam has a rectangular cross section with width b = 200 mm and height h = 250 mm.Determine the maximum permissible value q if the allowable bending stress is ?all = 11.2 MPa, and the allowable shear stress is ?all = 1.50 MPa. (Enter the magnitude in kN/m.)
Find the stress distribution at section ABCD for the block shown in mm in the following figure, If P=64 kN. For the same section, locate the line of zero stress. Neglect the weight of the block.
The rectangular bar has a width of w = 3.25 in. and a thickness of t = 2.00 in. The normal stress on plane AB of the rectangular block shown is 6 ksi (C) when the load P is applied. Assume a = 4 and b = 5. Determine the shear stress on plane AB.
Two steel [E = 29,800 ksi] pipes (1) and (2) are connected at flange B, as shown in the figure. Pipe (1) has an outside diameter of 5.750 in. and a wall thickness of 0.278 in. Pipe (2) has an outside diameter of 3.750 in. and a wall thickness of 0.209 in. Assume L= 10 ft and L›= 15 ft. If the normal stress in each steel pipe must be limited to 15 ksi, determine (a) the maximum downward load P that may be applied at flange B. (b) the downward deflection of flange B at the load that you determined in part (a).
A post having a hollow, circular cross sectionsupports a P = 3.2 kN load acting at the end of an armthat is b =1.5 m long (see figure). The height of thepost is L = 9 m, and its section modulus is S = 2.65x105 mm3. Assume that the outer radius of the post isr2 =123 mm, and the inner radius is r1 =117 mm.(a) Calculate the maximum tensile stress σmax andmaximum in-plane shear stress τmax at point A onthe outer surface of the post along the x axis dueto the load P. Load P acts at B along line BC.(b) If the maximum tensile stress and maximumin-plane shear stress at point A are limited to90 MPa and 38 MPa, respectively, what is thelargest permissible value of the load P?
A hydraulic punch press is used to punch a slot in a 0.60-in.-thick plate, as illustrated in the figure. If the plate shears at a stress of 39 ksi, determine the minimum force P (in kips rounded to the nearest tenths) required to punch the slot. Assume d = 0.75 in. and a = 4.00 in.
A cantilever beam of IPN 300 section and length L=3m supports a slightly inclined load P=2,5KN at the free end (see Figure Q2).2.1 Plot a graph of the stress ?? at point A as a function of the angle of inclination ?. [16]2.2 Plot a graph of the angle ?, which locates the neutral axis n-n, as a function of the angle ?. See Table F-2 of Appendix F for the dimensions and properties of the beam (When plotting the graphs, let ? vary from 0 ?? 10°).
The cross section of the CD part of the crane boom in the picture is a standard 50x150mm2. Determine the normal stress at the center of the part. Use exact values in the calculation, just round the answers!
Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded as shown. If F1 = 19 kips, F2 = 33 kips, and the normal stress in each rod must be limited to 29 ksi, determine the minimum diameter d2 required for rod (2).
Question 2) In the system given in the figure, a distributed load of w=36 kN/m acts on the rod AB of L=4 m length. The angle θ that the bar BC makes with the horizontal is θ=48°. The allowable normal stress for bar BC is σm= 221 MPa, and the allowable shear stress for pins at points A and B is τm=68 MPa. Bar BC has a rectangular section and the side length a of the section is given as a=34 mm. According to this;Question 2-A) Find the smallest b side length required for the bar section BC. (Write your result in mm.)Question 2-B) The connection type at point B is given in the figure next to it. Accordingly, find the smallest diameter required for pin B. (Write your result in mm.)

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

Two wooden members of uniform rectangular cross section are joined by the simple glued scarf splice shown. Knowing that P= 18 kN, determine the normal and shearing stresses in the glued splice. 75 150 mm 45° The normal stress is kPa. The shearing stress is kPa.