5-88 Underground water is to be pumped by a 78 percent efficient 5-kW submerged pump to a pool whose free surface is 30 mabove the underground water level. The diameter of the pipe is 7 cm on the intake side and 5 cm on the discharge side. Determine(a) the maximum flow rate of water and (b) the pressure difference across the pump. Assume the elevation difference between thepump inlet and the outlet and the effect of the kinetic energy correction factors to be negligible.FIGURE P5-88Pool30 m

To find-: (a) The maximum flow rate of water. (b) The pressure difference across the pump. Given-:…

Underground water is to be pumped by a 78 percent efficient S-KW submerged pump to a pool whose free surface is 30 m above the underground water level. The diameter of the pipe is 7 cm on the intake side and 5 cm on the discharge side. Determin (a) the maximum flow rate of water and (b) the pressure difference across the pump. Assume the elevation difference between th pump inlet and the outlet and the effect of the kinetic energy correction factors to be negligible. Pool 30 m

Underground water is to be pumped by a 78 percent efficient S-KW submerged pump to a pool whose free surface is 30 m above the underground water level. The diameter of the pipe is 7 cm on the intake side and 5 cm on the discharge side. Determin (a) the maximum flow rate of water and (b) the pressure difference across the pump. Assume the elevation difference between th pump inlet and the outlet and the effect of the kinetic energy correction factors to be negligible. Pool 30 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A D0 = 10-m-diameter tank is initially filled with water 2 m above the center of a D = 10-cm-diameter valve near the bottom. The tank surface is open to the atmosphere, and the tank drains through a L = 100-m-long pipe connected to the valve. The friction factor of the pipe is given to be f = 0.015, and the discharge velocity is expressed as V = √ _________ 2gz _________ 1.5 + f L/D where z is the water height above the center of the valve. Determine the initial discharge velocity from the tank.
A 73-percent efficient 12-hp pump is pumping water from a lake to a nearby pool at a rate of 1.2 ft3/s through a constant-diameter pipe. The free surface of the pool is 35 ft above that of the lake. Determine the irreversible head loss of the piping system, in ft, and the mechanical power used to overcome it.
Underground water is to be pumped by a 78 percent efficient 5-kW submerged pump to a pool whose free surface is 30 m above the underground water level. The diameter of the pipe is 7 cm on the intake side and 5 cm on the discharge side. Determine the flow rate of water and the pressure difference across the pump if the irreversible head loss of the piping system is 4 m.
A 78-percent efficient 12-hp pump is pumping water from a lake to a nearby pool at a rate of 1.7 ft3/s through a constant-diameter pipe. The free surface of the pool is 32 ft above that of the lake. Determine the irreversible head loss of the piping system, in ft, and the mechanical power used to overcome it. Take the density of water to be 62.4 lbm/ft3.
Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 23 kW of useful mechanical power to the water. The free surface of the upper reservoir is 57 m higher than the surface of the lower reservoir. If the flow rate of water is measured to be 0.03 m3/s, determine the irreversible head loss of the system and the lost mechanical power during this process.
Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 20 kW of useful mechanical power to the water. The free surface of the upper reservoir is 45 m higher than the surface of the lower reservoir. If the ?ow rate of water is measured to be 0.03 m3/s, determine the irreversible head loss of the system and the lost mechanical power during this process.
Seawater is to be pumped into a large tank at a rate of 165 kg/min. The tank is open to the atmosphere and the water enters the tank from a 80-m-height. The overall efficiency of the motor-pump unit is 75 percent and the motor consumes electricity at a rate of 3.2 kW. Take the correction factor to be 1. If the irreversible head loss in the piping is 7 m, the velocity of the water at the tank inlet is (a) 2.34 m/s (b) 4.05 m/s (c) 6.21 m/s (d ) 8.33 m/s (e) 10.7 m/s
Water is pumped from a lower reservoir to a higher reservoir by a pump that provides 20 kW of useful mechanical power to the water. The free surface of the upper reservoir is 40+0m higher than the surface of the lower reservoir. The flow rate of water is measured as 0.03 m3/s.Determine the irreversible head loss of the system and the lost mechanical power during this process.
A pump draws 20 kW of electrical power while pumping oil with a density of 780 kg/m^3 at a flow rate of 0.3 m^3/s. The diameters of the inlet and outlet pipes of the pump are 7 cm and 12 cm, respectively. Since the pressure increase in the pump is 220 kPa and the motor efficiency is 91%, determine the mechanical efficiency of the pump. (Ignore the kinetic energy correction factor, α=1, Ignore the height differences inside the pump, the head loss in the pump hL=0.5)
A water from Agno River is pumped using a submerged pump at an efficiency of 78% that is discharged to a swimming pool in Itogon which has a free surface of 30 m above the Agno River water level. The pipe that was used has a diameter of 7 cm on the suction line and 5 cm on the discharge line from the pump. If the power requirement of the pump is 5 kW assuming that the elevation difference between the pump inlet and outlet and the effect of the kinetic energy correction factors are negligible, calculate for the followinga) Power requirement by the pump in kWb) Pressure difference across the pumpc) Pumping cost/day(24 hour) if the electricity cost is ₱2.00/kW-hr
A water tank is attached to a piping system with a sharp edge inlet (KL=0.5). Determine the velocity of the outlet water if the system has two elbow pipes (KL=1.5), the length of the entire system is 10m, the diameter is 1.5cm, the friction factor is 0.002 and the height between the water and the outlet are 5m.
The shaft power of a turbine operating with 80 percent efficiency is 450 kW. If the mass flow rate through the turbine is 625 kg/s, the load removed from the fluid by the turbine iswhat is the amount? Take it as g=9.81 m/s2