Quiq plz Figure shows a sample power system network and Zpus Matrix elements. For a solid three phase fault take place at bus 3. Determine a) Fault current (b) V1,V2F and V3f (c) Post fault current in lines 1-2 and 1-3.The line from bus 1-2 impedance =j0.32p.uThe line from bus 2-3 impedance =j0.67p.uThe line from bus 3-1 impedance =j1.06p.uThe Zpus matrix element values areZbus Matrix Z13 = 0.1;Zbus Matrix Z23 =1.11;Zbus Matrix Z33 =145;FaultG2

Answered: Image /qna-images/answer/18ab22d7-92e2-4e1f-bc3a-5142dd1bd3f1.jpg

ure shows a sample power system network and Zpus Matrix elements. For a solid three phase fault take place at bus 3. Determine a) Fault current (b) V1, and V3f (c) Post fault current in lines 1-2 and 1-3. ne line from bus 1-2 impedance =j0.32p.u e line from bus 2-3 impedance =j0.67p.u he line from bus 3-1 impedance =j1.06p.u he Zbus matrix element values are ous Matrix Z13 = 0.1; Zous Matrix Z23 =1.11; Zbus Matrix Z33 =145; G1 Fault

ure shows a sample power system network and Zpus Matrix elements. For a solid three phase fault take place at bus 3. Determine a) Fault current (b) V1, and V3f (c) Post fault current in lines 1-2 and 1-3. ne line from bus 1-2 impedance =j0.32p.u e line from bus 2-3 impedance =j0.67p.u he line from bus 3-1 impedance =j1.06p.u he Zbus matrix element values are ous Matrix Z13 = 0.1; Zous Matrix Z23 =1.11; Zbus Matrix Z33 =145; G1 Fault

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter10: System Protection

Section: Chapter Questions

Problem 10.21P

See similar textbooks

Similar questions

At the general three-phase bus shown in Figure 9.7(a) of the text, consider a simultaneous single line-to-ground fault on phase a and line-to-line fault between phases b and c, with no fault impedances. Obtain the sequence-network interconnection satisfying the current and voltage constraints.
A three-phase circuit breaker has a 15.5-kV rated maximum voltage, 9.0-kA rated short-circuit current, and a 2.50-rated voltage range factor. (a) Determine the symmetrical interrupting capability at 10-kV and 5-kV operating voltages. (b) Can this breaker be safely installed at a three-phase bus where the symmetrical fault current is 10 kA, the operating voltage is 13.8 k V, and the (X/R) ratio is 12?
Equipment ratings for the five-bus power system shown in Figure 7.15 are as follows: Generator G1:Â Â Â Â 50Â MVA,Â 12kV,Â X=0.2 per unit Generator G2: 100Â MVA, 15 kV, X=0.2 per unit Transformer T1: 50 MVA, 10 kV Y/138kVY,X=0.10 per unit Transformer T2: 100 MVA, 15 kV /138kVY,X=0.10 per unit Each 138-kV line: X1=40 A three-phase short circuit occurs at bus 5, where the prefault voltage is 15 kV. Prefault load current is neglected. (a) Draw the positive-sequence reactance diagram in unit on a 100-MVA, 15-kV base in the zone of generator G2. Determine (b) the ThĂ©venin equivalent at the fault, (c) the subtransient fault current in per unit and in kA rms, and (d) contributions to the fault from generator G2 and from transformer T2.
Equipment ratings for the four-bus power system shown in Figure 7.14 are as follows: Generator G1: 500 MVA, 13.8 kV, X=0.20 per unit Generator G2: 750 MVA, 18 kV, X=0.18 per unit Generator G3: 1000 MVA, 20 kV, X=0.17 per unit Transformer T1: 500 MVA, 13.8/500YkV,X=0.12 per unit Transformer T2: 750 MVA, 18/500YkV,X=0.10 per unit Transformer T3: 1000Â MVA, 20/500YkV,X=0.10 per unit A three-phase short circuit occurs at bus 1, where the prefault voltage is 525 kV. Prefault load current is neglected. Draw the positive-sequence reactance diagram in per unit on a 1000-MVA, 20-kV base in the zone of generator G3. Determine (a) the ThĂ©venin reactance in per unit at the fault, (b) the subtransient fault current in per unit and in kA rms, and (c) contributions to the fault current from generator G1 and from line 1-2.
Consider the oneline diagram of a simple power system shown in Figure 9.20. System data in per-unit on a 100-MVA base are given as follows: The neutral of each generator is grounded through a current-limiting reactor of 0.08333 per unit on a 100-MVA base. All transformer neutrals are solidly grounded. The generators are operating no-load at their rated voltages and rated frequency with their ENIFs in phase. Determine the fault current for a balanced three-phase fault at bus 3 through a fault impedance ZF=0.1 per unit on a 100-MVA base. Neglect -Y phase shifts.