Use the following details The transformer has an applied voltage of 120 V. It has two windings. There are 100 turns in the primary and 200 turns in the secondary. 12. This transformer can be described as a/an step-up transformer step-down transformer autotransformer low-voltage transformer a. b. C. d.

Use the following details The transformer has an applied voltage of 120 V. It has two windings. There are 100 turns in the primary and 200 turns in the secondary. 12. This transformer can be described as a/an step-up transformer step-down transformer autotransformer low-voltage transformer a. b. C. d.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter3: Power Transformers

Section: Chapter Questions

Problem 3.32MCQ

See similar textbooks

Similar questions

An open-delta three-phase transformer system has one transformer center-tapped to provide a neutral for single-phase voltages. If the voltage from line to center tap is 277 V, what is the high-leg voltage?
For an ideal transformer, the efficiency is (a) 0 (b) 100 (c) 50
A single-phase step-down transformer is rated 13MVA,66kV/11.5kV. With the 11.5 kV winding short-circuited, rated current flows when the voltage applied to the primary is 5.5 kV. The power input is read as 100 kW. Determine Req1andXeq1 in ohms referred to the high-voltage winding.
An infinite bus, which is a constant voltage source, is connected to the primary of the three-winding transformer of Problem 3.53. A 7.5-MVA,13.2-kV synchronous motor with a sub transient reactance of 0.2 per unit is connected to the transformer secondary. A5-MW,2.3-kV three-phase resistive load is connected to the tertiary Choosing a base of 66 kV and 15 MVA in the primary, draw the impedance diagram of the system showing per-unit impedances. Neglect transformer exciting current, phase shifts, and all resistances except the resistive load.
A three-phase transformer rated for 33 kV/6.6 kV is connected Y- Δ and the protecting current transformer on the low voltage side have a ratio of 400/5. What is the ratio of the current transformer on the high voltage side? Ans 46.19:5 How I got this answer Please answer only typing format please
12. A transformer has a primary voltage rating of 240 V and a secondary voltage rating of 80 V. If the windings were connected subtractive, what voltage would appear across the entire connection? 13. If the windings of the transformer in Question 12 were to be connected additive, what voltage would appear across the entire winding? (Answer #13)
.Given is a 50 kVA, single phase transformer. The transformer is fed by a single phase ungrounded primary voltage of 12,500 volts. The secondary of the transformer is 240 volts. The transformer is feeding loads L1, L2, and L3. There is a permanent ground connection between loads L2 and L3. There is no other ground on the system. Ammeters A-3 and A-4 read 25A each. Give the full load primary current,the full load secondary current. What is the winding-to-winding ratio
Given is a 50 kVA, single phase transformer. The transformer is fed by a single phase ungrounded primary voltage of 12,500 volts. The secondary of the transformer is 240 volts. The transformer is feeding loads L1, L2, and L3. There is a permanent ground connection between loads L2 and L3. There is no other ground on the system. Ammeters A-3 and A-4 read 25A each. What percent is the transformer load? What will each of the ammeters read? With 25 amp flowing in ammeter A-4, the current that will be flowing in the ground ammeter A-6 will be?
The high-voltage side of a transformer has 750turns, and the low-voltage side has 50 turns. When thehigh side is connected to a rated voltage of 120 V,60 Hz, a rated load of 40 A is connected to the lowside. Calculatea. The turns ratio.b. The secondary voltage (assuming no internaltransformer impedance voltage drops).c. The resistance of the load.
76. A 200-kVA, 2300/460 V, 60-Hz two-winding transformer is to be used as an autotransformer to step-up the voltage of 2300 V to 2760 V. Determine kVA rating of autotransformer. A. 200 C. 1200 B. 800 D. 1500
2. a) what is the ratio of the number of winding required in the transformer to be used to adapt a 4-ohm speaker to a 100-ohm source? b) 100V and 1A are applied to the input of a transformer with a 2: 1 ratio. What are the voltage and current values at the output of the transformer?
true or false 1-A transformer in which part of the winding is common to both the primary and secondary circuits know as auto-transformer transformer 2-while conducting short- circuit on transformer the secondary side is short-circuit 3-a transformer core is laminated to reduce hysteresis losses 4-The distribution transformer is used to supply stepped down and stepped up values of voltage 5-The secondary winding of current transformer consists of a large number of turns