Using Noda analysis method ,calculate the current la and 13 for thecircuit shown.أجب على السؤال اأدناه , على أن تكون تكون الاجابة علىورقة , ت تضمن الاسم الثلاثي والتاريخ وتوقيع الطالب , و يتم.تحمیل صورة واضحة ل لورقةR1R3 I35010ΩR4150R2E500la80 V75 la

Nodal analysis uses Kirchhoff's current law and ohm's law. The detailed solution is attached with.

Using Noda analysis method, calculate the current la and 13 for the circuit shown. * أجب على السؤال أدناه , على ان تكون تكون الاجابة على ورقة , ت تضمن الاسم الثلاثي والتاريخ وتوقيع الطالب , و يتم .تحميل صورة واضحة ل لورقة I3 R1 R3 50 10Ω R2 R4 E 50 Ω | la 150 80 V 75 la

Using Noda analysis method, calculate the current la and 13 for the circuit shown. * أجب على السؤال أدناه , على ان تكون تكون الاجابة على ورقة , ت تضمن الاسم الثلاثي والتاريخ وتوقيع الطالب , و يتم .تحميل صورة واضحة ل لورقة I3 R1 R3 50 10Ω R2 R4 E 50 Ω | la 150 80 V 75 la

EBK ELECTRICAL WIRING RESIDENTIAL

19th Edition

ISBN:9781337516549

Author:Simmons

Publisher:Simmons

Chapter19: Special-purpose Outlets-water Pump, Water Heater

Section19.2: Water Heater Branch Circuit

Problem 9R: An 80-gallon electric water heater has 60F (15.56C) incoming water. How many minutes can a...

See similar textbooks

Similar questions

Don't copy Reply asap.. What is salometer ?
CALCULATE dBm( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).
If the turn on and turn off energy losses in a transmitter are 51 mJ and 76.8 mJ respectively and the mean power loss is limited to 200 W, what is the maximum switching rate that can be achieved ? A)15649 cycles/sec B)156.49 cycles/sec C)1564.9 cycles/sec D)15.649 cycles/sec
Kindly do ASAP
Genset control is useful when: a. Power optimization b. PV system need to be coupled with wind turbine system c. Diesel generator produce variable frequency d. All e.None
3nu(-n) 0.1nu(-n) + 2nu(-n) Determine if stable system or not using infinite geometric series formula
What is the speed [km/hr]of an ambulance with a siren frequency of 1KHz if you hear it at 1.10 kHz? a. 40 b. 80 c. 120 d. 160 e. 200
9/ Incoming and outgoing lines in a substation are connected to a Busbar. Select one: True False
Using nodal analysis, determine the value of voltages at models 1 and 2 in Fig. 15.23.
The figure below shows a radial transmission system with a generator having a terminal voltage of 95 KV at angle of10.5°. The load demand is 50 MW at a power factor of 0.88 lagging. Use a base of 128.4MVA . Instructions :round of to 2 decimal places. Calculate the following : 1.Per unit voltage of the transformer 1 2.Per unit impedance of the line. 3.Resistance of the transmission line when the load consumes full-load (Ω).
Perform the following steps for the given circuit in below.RD = 1.8kΩ, RS = 560Ω, RG = 2.2MΩ, VDD = +9V, IDSS = 6mA, VP = -6Va) Calculate the ID current and VDS voltage of the JFET.b) Calculate the ID current and VDS voltage of the JFET, if the value of IDSS = 8mA,VP = -6V.c) Calculate the ID current and VDS voltage of the JFET, if the value of IDSS = 6mA,VP = -4V.d) Find the working region of the JFET for the all cases given above.
6. A generator delivers power through a transmission line at 23 kV. The resulting line loss across the 23-kV transmission line is 7.6 MW. To reduce the losses, a step-up transformer rated 23 KV/230 kV is used. What will be the new loss in MW across a 230-kV transmission line? (four decimal places)