В 15 ft

Q: Determine the magnitude of the L. equivalent concentrated load that acts on bar AB. а 480 N с 360 N ...

A: The free body diagram for the rod AB is given below, (a) The magnitude of the equivalent concentrat...

Q: A frame is used to support 3 point loads as shown (a) Which members are 2 force members? (b) Draw FB...

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you. ...

Q: Two rollers of the same diameter

A: The free body diagram of roller 1 is given below, The expression that can be obtained by taking the...

Q: For the composite wall given in the sketcha) Determine the rate of heat transfer through the wallb) ...

A: Given: LA=10 mm =0.01 mkA=0.16 W/mKLB=150 mm=0.15 mkB=0.65 W/mKLC=20 mm=0.02 mkC=0.10 W/mKTi=20°CTo...

Q: what are velocity components,potential function and stream function? Uo=1m,teta=pi/6,r=1m,r0(zero)=1...

A: Stream Function→ for 2D flow and 3D axial symmetric flows stream functions are defined. stream funct...

Q: A uniform plank is 5.00 m long and weighs 100 N. The cord that attaches to the plank 1.00 m from the...

A: From the above diagram We can say that the above system is in equilibrium and the net torque acting ...

Q: Collar A has a mass of 3 kg and is attached to a spring of constant 1200 N/m and of undeformed lengt...

A: Given Mass = 3 kg Spring constant = 1200 N/m Undeformed length = 0.5 m r = 0.3 m vo = 2 m/s To find ...

Q: A 54g54g copper calorimeter contains 80cm380cm3 at 20∘C20∘C. A very cold 110g110g copper cylindrical...

A: Given Data Mass of the calorimeter is: mc=54 g Volume of the water is: vw=80 cm3 Density of water i...

Q: When fluid in a pipe is accelerated linearly from rest, it begins as laminar flow andthen undergoes ...

A:

Q: Q2: Water is flowing through an inclined pipe and two sections (section 1 and section 2) of the pipe...

A: Data given - d1 = 263 mm = 0.263 m d2 = 173 mm = 0.173 m z1 = 773 mm  = 0.773 m z2 = 373 mm = 0.373 ...

Q: When particles are interconnected by a cable, the motions of the particles are Lütfen birini seçin: ...

A: When particles are interconneted by a cable, the motions of the particles are always dependent. 

Q: Air flowing steadily in a nozzle experiences a normal shock at a Mach number of Ma = 2.6. If the pre...

A: Given Mach number = 2.6 Pressure of the air = 58 kPa Air temperature = 270 K To find Pressure downst...

Q: An adiabatic air compressor is to be powered by a direct-coupled adiabatic steam turbine that is als...

A: Given, Inlet pressure of steam in the turbine; P1=12.5 MPa The inlet temperature of steam in the tur...

Q: Answer for J and K

A:

Q: To get up on the roof, a person (mass 66.7 kg) places an aluminum ladder (mass 9.30 kg) against the ...

A: Given, The mass of the person, mP=66.7 kg The mass of the ladder, mL=9.3 kg All the given dimensions...

Q: A basketball player weighing 200 lb hangs on the rim of the basketball hoop shown below. The vertica...

A:

Q: Explain the role of mechanical properties in load-bearing applications using real-world examples

A: Examples of load-bearing applications are a car traveling on the road, the human body, aircraft, and...

Q: The resultant of the pressure and wall shear forces acting on a body is measured to be 430 N, making...

A: The drag force  FD=FRcos30°=430cos30°=372.4N

Q: 1. A .6kg block is hung from a spring with a force constant of 25 N/m. Calculate the displacement of...

A: Data given -  Mass of the block = 0.6 kg  Force constant k = 25 N/m

Q: Determine the n- and t-components of the force F which is exerted by the rod AB on the crank OA. Eva...

A:

Q: The viscosity of a fluid placed in a gap of two cylinders is measured with the apparatus given in th...

A:

Q: 5-41. Determine the resultant force at pins A, B, and C on the three-member frame. S00 N 200 N/m 2 m

A: Draw the free-body diagram AC Take the moment about A ∑MA=0Cy2tan60°+Cx×2-2002sin60°1sin60°=01.155C...

Q: An orifice meter with orifice diameter 15 cm is inserted in a pipe of 30 cm diameter. The pressure g...

A:

Q: a) Calculate the strain components (Exx, Eyy, Ɛzz, Yxy, Yxz and Yyz).

A:

Q: What simplifi cations have been made, in the potential fl owtheory of this chapter, which result in ...

A: Some equations depends upon the parameters like Shape of the body Orientation of the free stream Lo...

Q: Q#2 When the load P is applied to the right end of the cantilever beam as shown in the figure, defle...

A: The deflection at point B can be shown as the summation of the deflection due to concentrated load a...

Q: If the modulus of ragidity of steel 12 80GPa,  what is the diameter of the shaft required? What is t...

A: Given data: Modulus of rigidity of steel shaft = 80 GPa                    N = 240 RPM              ...

Q: When studying whiplash resulting from rear-end collisions, the rotation of the head is of primary in...

A: Given:Angular accleration of head,α=700cosθ+70sinθNow,Angular acceleration,α=dωdt=ωdωdθwhere ω=angul...

Q: Please do the last two questions (3 and 4)! Thank you in advance!  A seesaw that weights 45lbs and i...

A: Given Data, W = Weight of the seesaw = 45 lb L = Length of the seesaw = 5 m Condition 1 :-  Accordin...

Q: An axial flow compressor stage has blade root, mean and tip velocities of 160, 200 and 240 m/s. The ...

A: The basic phenomenon involved in axial flow compressor is kinetic energy utilizes to the rotate the ...

Q: The mobile shown is in equilibrium. Mass 2 is 0.2675 kg. Determine the masses of the objects 1, 3, a...

A:

Q: The uniform 5-m-long round wooden rod in Fig.  istied to the bottom by a string. Determine ( a ) the...

A:

Q: Compute the atomic packing factor (APF) for CSCI. Hint: The ions touch along the body diagonal.

A: For the given conditionWe havea=2rcs+2rCl3a=20.17+20.1813a=0.4 nmUni cell volume is given asVc=a3Vc=...

Q: Determine the force in each member of the roof truss shown. State whether each member is in tension ...

A: In the given problem, firstly we will determine the support reactions at A and E. There after, metho...

Q: In the figure, a tin of anti-oxidants (m1 = 4.4 kg) on a frictionless inclined surface is connected ...

A:

Q: mechanics of materials

A: Given:(σb)fail in cast iron=550MPaτfail in steel=450MPaFactor of safety for castiron=2.2Factor of sa...

Q: When is a system a closed system, and when is it a control volume?

A: Closed system: A closed system is defined when a particular quantity of matter is under study. A clo...

Q: Calculate the area moment of inertia around the x and y axes. Dimensions are in mm. 100 50 50 100

A: The height of the rectangle is h=200 mm. The  breadth of the rectangle is b=150 mm. The radius of th...

Slope and Deflection

The slope in a deflected beam is described as an angle in radians made by the tangent of the section with the original axis of the beam. The deflection at any point on the axis of the beam is defined as the lateral displacement of the point before and after loading.