VCC=5V R1 3.3kn R2 3.3kn R4 1000 DA Q1 A • ВС237 1N400X DB A LED1 D3 R3 1N400X 1N400X 3.3ka Which of the following is true for the gate circuit realized with the transistors and diodes given above? O If logic 1 is given to A and Logic 1 is given to B, the diodes DA and DB are cut off. O This figure belongs to an OR (or) gate circuit. The led turns on if logic 1 is given to A and logic 1 to B. O If logic 1 is given to A and logic O is given to B, the led will not light.

VCC=5V R1 3.3kn R2 3.3kn R4 1000 DA Q1 A • ВС237 1N400X DB A LED1 D3 R3 1N400X 1N400X 3.3ka Which of the following is true for the gate circuit realized with the transistors and diodes given above? O If logic 1 is given to A and Logic 1 is given to B, the diodes DA and DB are cut off. O This figure belongs to an OR (or) gate circuit. The led turns on if logic 1 is given to A and logic 1 to B. O If logic 1 is given to A and logic O is given to B, the led will not light.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

What are the values of Aυ, Rin, Rout, and Ai for the common-gate stage shown operating with gm = 0.6 mS, RI = 50 Ω, R4 = 3 kΩ and RL = 82 kΩ? (b) What are the values if RI is changed to 5 kΩ? (Ai = io/ii ). What is the smallsignal limit for the value of υi in this circuit?
Design an interfacing circuit for ADC 0804 and 8051 microcontrollerwith self-clocking. Also explain the functions of INTR and WR pins ofADC 0804.
Draw the schematic of a three-input NAND gate. What are the W/L ratios for thetransistors based?
The common-emitter output characteristics for annpn transistor are given . What are thevalues of βF at (a) IC = 5 mA and VC E = 5 V?(b) IC = 7 mA and VC E = 7.5 V? (c) IC = 10 mAand VC E = 14 V?
Please explain it to me and simplify this function and draw the circuit using two-level Nand and Nor circuit. F(a,b,c,d)={ (0,3,12,15)
The switches as shown can be implemented using MOSFETs, as shown. What must be the W/L ratios of the transistors if the onresistance of the transistor is to be less than 1 percent of the resistor 2R = 12 kΩ? Use VREF = 3.0V. Assume that the voltage applied to the gate of the MOSFET is 5Vwhen b1 = 1 and 0Vwhen b1 = 0. For the MOSFET, VTN = 1 V, Kn = 50 μA/V2, 2φF = 0.6 V, and γ = 0.5√V.
Q1: Design and implement an asynchronous counter that counts from 0000 up to 1100 (modulus 13). Use OR gate, and show in the drawing how the OR gate is connected to truncate the state 1101.
The ECL-100K gate shown is redesigned tooperate at a power of 10 mW. (a) What is the gatedelay of the new design? Assume a constant powerdelayproduct. (b) What power is required to achievea delay of 0.2 ns?
1) Draw how an ASIC, SOC, MCU, MPU, DSP any TTL gates of the TTL circuits you have constructed or designed to use a transistor (BJT/MOS) to drive the current specification of a LOAD (ie RELAY, Motor, Light array of High powered LEDs)
Discuss the pin diagram of any logic gate? Explain how the NAND gate can be used to derive the other logic gates. Discuss the application of diode as positive series clipper positively biased with ideal diode, practical silicon diode. Draw the neat waveform diagrams. Elaborate the working of half wave rectifier with neat diagram and waveforms. Determine the peak output voltage and current in the 4 kW load resistor connected to the output terminals of full wave bridge rectifier, if the transformer secondary voltage is 28 Vrms. Use the practical silicon diode model. Discuss the types of transformers with their applications. Explain with a neat diagram an isolation transformer used for electrical power transmission. Also explain the transformation ratio. Explain the difference between single phase and three phase induction motors with their application in detail. Determine the back emf generated in the dc shunt motor if it takes 250 V, 41 A current while running at full load. Assume…
Simplify the following functions, and implement them with two level NAND gate circuits: F (A, B, C, D)=A′+B+D′+B′C
Simplify the following functions and implement them with two-level NAND gate circuits: F(A,B,C,D) = A' + B + D' + B'C