Water at 60 degrees Fahrenheit have a density of 62.36 lb/ft.^3 and dynamic viscosity of 7.536 x 10^-4 lb/ft-s) is flowing steadily in a 2-inch diameter horizontal pipe made of stainless steel at a rate of 0.2 ft^3/s. Use f = 0.0200. Determine the head loss in terms of inches over a 200-feet long section of the pipe. 376.05   27.30   None of the above   327.60

Q: Steam has a quality of 90% at 2000C. Determine (a) the enthalphy; (b)the specific volume

A: Given data, x = 90% = 0.9          ( x = steam quality ) T = 200°C Find    h , v 

Q: 2.The block on the incline has a mass of 50 kg and the hanging weight 100 kg. The coefficient of fri...

A:

Q: The vibration amplitude of a one degree-of-freedom harmonically forced undamped oscillator is in res...

A:

Q: 3. A 220-mm-diameter steel shaft have a maximum shearing stress of 12 GPa. Determine the applied tor...

A: Write the formula for shear stress in the shaft under torsion. τ=16Tπd3 Here, τ is the shear stress ...

Q: For the disk rolling without slipping, if its radius r= 1.4 m, and its angular velocity W = 5.6 rad/...

A:

Q: Write, but do not solve, the equations of motion for the translation mechanical system shown in the ...

A:

Q: The Capacity Planner of Primal Waters is tasked to ensure the maximum amount of water flows from Pum...

A: When the pump is not in operation, From the diagram, f=0.02  LAB (Length of pipe AB)= 1000m LBC (Len...

Q: Find the minimum principal stress if maximum shear stress is 10 MPa and maximum principal stress is ...

A:

Q: In the case of heating the air with a heating coil, the absolute humidity of the air   can either i...

A: Given Air To find Absolute humidity of the air heating with heating coil

Q: Describe the steps involved in the preparation of a metallographic sample: > Sectioning (cutting) > ...

A:

Q: At what angle 0 must the 800-lb force be applied in order that the resultant R of the two forces has...

A:

Q: Air enters the compressor of an ideal gas refrigeration cycle at -23°C and enters the turbine at 17°...

A:

Q: Find the discharge if flow velocity 0.8 m/s and area of channel 0.3 m2

A: Given data : Area of channel=A Flow velocity=V   Find : Discharge 

Q: required width (bmin) if the allowable bending stress in the material is 16 MPa ? If the beam shown ...

A:

Q: A small ship capable of making a speed of 6.5 knots through still water maintains a heading due east...

A:

Q: ) is the fluid in the pipe shown below and mercury (s = 13.6) is the fluid in the manometer. If the ...

A:

Q: wafer It is rexuired to pump a coclingrom a stornge pond to a ondonser ina proress plant situa ted l...

A: Level difference between pond and condenser, ∆z=10 mLength of the pipe, L=200 mPipe diameter, d=75 m...

Q: 5. In a T-s diagram, how are the isentropic and actual processes represented. Please select all answ...

A:

Q: 2.A mountain has top pressure reading of 1 atm while its bottom has 2bars. The density of air in the...

A: GIVEN DATA- PRESSURE AT TOP = 1atm PRESSURE AT BOTTOM = 2bar DESNITY OF AIR = 1.18 kg/m3 WE AHVE TO ...

Q: Train A is traveling at a constant speed va = 34 mi/hr while car B travels in a straight line along ...

A:

Q: Water at 60 degrees Fahrenheit have a density of 62.36 lb/ft.^3 and dynamic viscosity of 7.536 x 10^...

A:

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be u...

A:

Q: Find the weight in Newton of the floating cylindrical can in Fig. 6-9.

A: Answer: The weight of the floating cylinder is 3.4520 Newtons.  

Q: 10.3 An electronic signboard is attached to a five-storey building consisting of special moment-resi...

A: Since signboard is a displacement sensitive nonstructural element, it should be designed for seismic...

Q: Differentiate Visual Flight Rules (VFR) to Instrument Flight Rules (IFR)

A: Difference between VFR and IFR :

Q: 2 kg of Refrigerant-134a contained in a piston-cylinder device undergoes a reversed Carnot cycle. So...

A: Given: After the adiabatic compression, temperature is→T2=30°C=303.15  K Because after the adiabatic...

Q: Define the Rockwell Scale

A: Rockwell method: It is a hardness testing method that is used to measure the hardness of any metal o...

Q: P1-1. Draw a free-body diagram of the ring at A and identify each force. 30 45° 200 N 500 N

A: As per bartleby guidelines we are allowed to solve only 1st question if multiple questions are poste...

Q: required width (bmin) if the allowable bending stress in the material is 16 MPa? If the beam shown i...

A:

Q: m k 0.61 0.61 Drive the equation of motion of the above structure using two methods comparing the eq...

A:

Q: An ammonia vapor refrigeration cycle operates at an evaporator temperature of -16 °C and a condensin...

A:

Q: Q1) Prove that the equation for one dimension unsteady state conduction with heat

A: For 1-D unsteady state conduction with heat generation is given by...

Q: IS determine the weight of the combine system

A: To determine the Weight of combine system.

Q: A 20 kg object is attached to a spring with spring constant 260 kg/s?. It is also attached to a dash...

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any ...

Q: (11) The cold-drawn AISI 1018 steel bar shown in the figure is subjected to an axial load fluctuatin...

A: Metal fatigue is a term that describes the sudden failure of metal parts due to gradual fracturing w...

Q: Water (Cp = 4200 J/kg. °C) is used cool an unknown fluid (with a given Cp = 3810 J/kg.ºC) using a tw...

A: Find the maximum heat transfer between the fluids.

Q: vehicle model is tested in a wind tunnel. The model scale is 1:2. The original speed of the vehicle ...

A:

Q: Steam at 6000 kPa, 400 degrees Celcius expands in a Rankine Turbine to 0.038 MPa. For 136 kg/s of st...

A: GIvenP1=6000kPa=6MPaT1=400oCP2=0.038MPa=38kPams=136kg/sBSR=4.80kg/kWh

Q: The 3.0 kg pendulum with mass center G is pivoted at A to the ficed support CA. It has a radius o gy...

A:

Q: Q1// A heat engine operates between a source at 550°C and a sink at 25°C. If heat is supplied to the...

A:

Q: A weight of 160 lb falls from a height of 2.5 ft to the center of a horizontal platform mounted on f...

A:

Q: At what angle 0 must the 800-lb force be applied in order that the resultant R of the two forces has...

A: Given data Force 1 = P = 1400 lbForce 2 = Q = 800 lbAngle between the two forces = θResultant =R = 2...

Q: Calculate the maximum load (P) that can be supported by the knuckle joint that shown in the figure b...

A:

Q: A mass of 1.25 kg stretches a spring 0.06 m. The mass is in a medium that exerts a viscous resistanc...

A: NATURAL VIBRATION The vibration in which there is no kinetic friction at all as well as there is no ...

Q: Find the displacement if work done 2.1 J and force applied 3 N

A: Given data : Work done=W Force=F   To find : Displacement

Q: A refrigerator uses R-134a as its working fluid and operates on an ideal vapor- compression refriger...

A:

Q: P1-1. Draw a free-body diagram of the ring at A and identify each force. B. 30 45° 200 N 500 N

A:

Q: The maximum flow rate is 4437.02 O barrels per day.

A: To find Maximum flow rate

Q: The position of point P can be represented in the curve by 3 point (3) point (2) point (1) point (4)

A: It is required to choose correct option

Q: Discussion: 1- Define buoyancy and metacentric height ?

A: As per our guidelines, we are supposed to answer only first one question in case of multiple questio...

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.