Water discharge flow rate of 0.001 m3/s is delivered through the 30 mm cast iron pipe? €=0.15 Calculate the total losses in the pipe  For minor losses, take K for the Entrance: 0.3 Exit: 0.5 Valve 1.8 the pipe Length  L_687 m

Q: ron pipes and conducts water at 20 ° C from eservoir "A" to reservoir "B", the levels of which are…

A:

Q: 49. Water flows at a rate of 200 GPM into a piping system connected in series. Length, diameter, and…

A: Since, pressure drop calculations and equivalent pipe diameter calculations are two different…

Q: A pipe is used for energy transmission. Length and diameter of pipe are 80 m and 50 cm respectively.…

A:

Q: 82 ft of cast iron pipe of 1.5-nominal diameter. All fittings are d regular. Determine the flow rate…

A: given: diameter d=1.5ft height h=23ft

Q: Calculate the horizontal force acting on the conical part of the pipe! $50 mm = 3.5 m' / min O 200mm…

A:

Q: Recommend the low cost flow meter used in industries for measuring flow that provides negligible…

A: Reynold number is the ratio of inertia forces to the viscous forces. Reynold number signifies the…

Q: A 300mm x 300mm pipe discharges 600 L/s of water where the length is 30m. Determine the head loss if…

A:

Q: A fluid with a specific weight of 78.5 lb/ft³ and dynamic viscosity of 0.638 lbs/s-ft is flowing at…

A:

Q: Find the pressure drop(kPa) in a 29m length of pipe with a triangular cross section. Q = 22m3/min f…

A:

Q: A pipe is used for energy transmission. Length and diameter of pipe are 80 m and 50 cm respectively.…

A:

Q: Heavy fuel oil is pumped at a flow rate of 88 L/s through a new steel pipe. What diameter of the…

A:

Q: The volume flow rate of water is 669,91 liters/min. Calculate the maximum length of the pipe [m],…

A:

Q: Water is flowing inside a pipe with a constant cross section. Calculate the total head loss. The…

A: Given Data: Elevation, h2=100 ft

Q: Problem: : Determine the size of clean wrought-iron pipe required to convey 4000 gpm oil, v = 0.0001…

A:

Q: The observed pressure drop for 40°F water flowing at 16 ft/min in a 4.5-in diameter pipe is 9.68 x…

A:

Q: 1.2 A pipe of 50 mm diameter and 45 m long is connected to a large tank, the entrance to the pipe…

A:

Q: A 25% Calcium Chloride brine is to be pumped through a line at 250 gpm at a temp. of 0 deg. If the…

A: Given that, Flow rate of chloride, Q=250 gpm,Pressure drop inside pipe, ∆P=0.006 lb·force/in2-ft…

Q: The 1/2 inch diameter hose can withstand a maximum pressure of 200 psi without breaking. Determine…

A:

Q: A horizontal pipe has a sudden contraction from DN100 to DN80 Schedule 40 steel pipes. The water…

A: Since we only answer up to 3 subparts, we will answer first 3. Please resubmit the question and…

Q: If the shear stress at the wall of a 12′′ diameter pipe is 1.00 psf and f = 0.040, what is the…

A:

Q: What is the level h required to deliver a flow rate of 0.425 L/s through the 1.25 cm smooth pipe.

A:

Q: A 300 mm diameter main is required for a town water supply. As pipes over 250 mm diameter are not…

A:

Q: A valve incurs a head loss equal to 2.2 meters length of pipe having a diameter of 8.6 cm and a…

A:

Q: pipe with 20 mm diameter as shown in Figure Q3. If the pressure at point 1 is P1 kPa. Determine the…

A: since P1 value is not given then assume that P1= gauge pressure at point 1 in kpa. Take density of…

Q: Determine the size of galvanized steel pipe needed to carry water for a distance of 180 m at 85 Li/s…

A: Given, Length (L)= 180m  Discharge (Q) = 85 L/s = 0.085 m3/s Head loss (hf)= 9 m ε = 0.15 mm =…

Q: Problem 2 The 10 cm galvanized-steel pipe is 1000 m long and discharges water into the atmosphere.…

A:

Q: A venturimeter is connected in a pipe carrying water. The diameter of pipe is 250 mm. The difference…

A: Given that, d1=250 mm=0.25 m, Q=0.05 m3/s x=45 mm pf Hg=0.045 m of Hg, Cd=0.96

Q: Water at 15 °C flows through a 300 mm steel pipe with roughness 3 mm. The corresponding head loss is…

A: Given steel pipe,  diameter, d=300 mme=3mmhead loss hL=6 mLength, L=300 mρ=1000kg/m3,  μ=10-3 N-sm2…

Q: r=20mm, the friction factor , the shear stress at pipe wall and the head loss per meter of the pipe…

A: Given: s=0.85 ρ=850 kg/m3ν=1.8×10-5 m2/sD=100 mmQ=0.50 L/sTo determine:Center line velocityvelocity…

Q: Calculate the head loss in 2000 ft of 14-in diameter cast iron pipe at a flow rate of 1000 gpm. Use…

A: To find: The head loss in the pipe. Given: The length of the pipe is L=2000 ft. The diameter of the…

Q: 2. Determine the required diameter of the galvanized iron pipe (e-o.15 mm) in Fig. 2 if the…

A: The entire mechanical energy of the flowing fluid, which includes the gravitational potential energy…

Q: Calculate the axial stress induced in the pipe is the water mean of 1.5 metres diameter and 20 mm…

A: Heare, pipe is cylindrical in nature. Asume that there is restriction in logitudnal direction and…

Q: The shower head shown in the Figure delivers water at 50°C. An orifice-type flow reducer is to be…

A:

Q: The volume flow rate of water is 654,55 liters/min. Calculate the maximum length of the pipe [m],…

A:

Q: A 8-in diameter steel pipe. is used to discharge water. If the roughness coefficient is equal to…

A: Given: The diameter of pipe, d = 8 in The roughness coefficient, n = 0.19 The head loss, h = 400 ft

Q: F- In a circular pipe of diameter 100 mm a fluid of viscosity (7) poise and sp. gr. 1.3 is flowing.…

A: Reynold's number is the ratio of inertia force and viscous force. It is a dimensionless number used…

Q: For the piping system of Fig. all pipes are concrete with a roughness of 0.04 inch. Neglecting minor…

A:

Q: The volume flow rate of water is 669,3 liters/min. Calculate the maximum length of the pipe [m],…

A:

Q: Water is flowing through an orifice meter at a rate of 0.096 m² /sec. The diameter of the pipe is…

A:

Q: Water is flowing inside a pipe with a constant cross section. Calculate the total head loss. The…

A: Answer: The total head loss is 38.422585 ft.

Q: Calculate the diameter of pipe if, flow rate is 20 l/min and flow velocity is 5 cm/s. Select one: O…

A: flow rate is defined as the volume flow rate per unit time.

Q: 2. An inclined venturi tube containing water has an inlet of 300 mm diameter and a throat of 150 mm…

A:

Q: 10. What size of pipe is required to carry 450 liters per second of water with a head loss of 3.4 m…

A:

Q: 10. What size of pipe is required to carry 450 liters per second of water with a head loss of 3.4 m…

A: Given:-  Discharge (Q) = 450 L/s = 0.450 m3/s head loss = 3.4 m length (L) = 5000 m friction factor…

Q: In a commercial steel pipe of diameter 0.01906 (in meters), industrial waste water (approximate as…

A: Given Data: The diameter of the pipe is, D=0.01906 m. The average velocity of water is, V=30 m/s.

Q: 2. Determine the size of galvanized steel pipe needed to carry water for a distance of 180 m at 85…

A:

Q: Water mass flow rate of 2kg/s is delivered through the 30 mm commercial steel pipe? -0.15 Calculate…

A: Given: mass flow rate of water→m˙=2 Kgs Diameter of the commercial steel pipe→D=30 mm=0.030 m So…

Fluid Dynamics

The study of the flow of gases and liquids, usually in and around solid surfaces, is known as fluid dynamics in physics and engineering. Fluid dynamics, for example, can be used to evaluate the movement of air through an airplane wing or the surface of a vehicle. It can also be used in ship design to increase the speed at which ships pass through water.