Answered: pipe with 20 mm diameter as shown in…

Name: Q3) Water is pumped from point 1 (basement) to point 2 (water reservo
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Q3) Water is pumped from point 1 (basement) to point 2 (water reservoir) using copperpipe with 20 mm diameter as shown in Figure Q3. If the pressure at point 1 is P1 kPa.Determine the water flow rate.Data: KĻ for elbow =1.5; globe valve = 10 and fri

Engineering

Mechanical Engineering

pipe with 20 mm diameter as shown in Figure Q3. If the pressure at point 1 is P1 kPa. Determine the water flow rate.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The system in Fig. consists of 1200 m of 5 cm castiron pipe, two 45° and four 90° flanged long-radius elbows,a fully open flanged globe valve, and a sharp exit into areservoir. If the elevation at point 1 is 400 m, what gagethe pressure is required at point 1 to deliver 0.005 m3/s of waterat 20°C into the reservoir?
Q3: Find the diameter of a circular orifice to discharge (0.015m '/ sec) under a head of (2.4m). If the orifice is in a vertical plane and the jet falls (0.25m) in a horizontal distance of (1.3m) from the vena-contracta. Find the head loss through the orifice
Two 32-in pumps from Fig. are to be used in seriesat 1170 r/min to lift water through 500 ft of vertical castiron pipe. What should the pipe diameter be for most effi -cient operation? Neglect minor losses.
The 28-in-diameter pump in Fig. at 1170 r/min isused to pump water at 20°C through a piping system at14,000 gal/min. (a) Determine the required brake horsepower.The average friction factor is 0.018. (b) If there is65 ft of 12-in-diameter pipe upstream of the pump, how farbelow the surface should the pump inlet be placed to avoidcavitation?
Water at 20°C is to be pumped through 2000 ft of pipe fromreservoir 1 to 2 at a rate of 3 ft3/s, as shown in Fig. P6.62.If the pipe is cast iron of diameter 6 in and the pump is75 percent efficient, what horsepower pump is needed?
A 50 mm diameter siphon discharges oil (SG=0.88) from a reservoir (elev. 20m) into open air (elev. 15m). The head loss from the reservoir (point 1) to the summit (point 2, elev. 22m) is 2.5 times the velocity head in the siphon and head loss from the summit to the discharge end is 4 times the velocity head in the siphon. What is the absolutepressure at the summit (point 2) assuming the atmospheric pressure to be 101.3 kPa? Do not write the unit. You will only input the numerical answer in the space provided. Unit of the Correct Answer: kPa (indicate the sign if negative) Decimal Places required in the final answer: 3
1. Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m. If the NPSHr is 3m less than the NPSHa you got on question number 1, determine the pump suction specific speed at pump rotating at 1800rpm and Q=500gpm
Water flows upward in a vertical 300-mm pipe at the rate of 0.222 m /s. At point A in the pipe the pressure is 210 kPa. At B, 4.57 m above A, the diameter is 600 mm, and the lost head A to B equals 1.83 m. Determine the pressure at B. indicate the free body diagram
A centrifugal pump having a head-capacityrelationship given by the equation ha=180 –6.10 X 10-4 Q2, with ha in feet when Q is ingpm, is to be used with the system shownin the figure, For Z2-Z1= 50 ft, what is theexpected flowrate if the total length ofconstant diameter pipe is 600 ft and thefluid is water? Assume the pipe diameter tobe 4 inch and the friction factor to be equalto 0.02. Neglect all minor losses.
The plunger diameter of a single-acting reciprocating pump is 115 mm and the stroke is 230 mm. The suction pipe is 90 mm in diameter and 4.2 m long. If cavitation takes place at the suction head of 4 m, the barometer stands at 10.3 m of water, and the water level in the sump is 3 m below the pump cylinder axis.3.1 Find the maximum allowable speed to operate the pump3.2 What power is expected in overcoming friction at this speed, take ƒ = 0.01
Water from a reservoir passes over a dam through a turbine and discharges from a 70-cm ID pipe at a point 95 m below the reservoir surface. The turbine delivers 0.950 MW. Calculate the required flow of water in m3/min if friction is neglected. If friction were included would a higher or lower flow rate be required? (Note: The equation you will solve in this problem has multiple roots. Find a solution less than 1.0 m3/s.) V=___m^3/min?
reservoir with water pressurized pipe diameter is 5 cm. The head loss in the system as given by hL= 5V^ 2/ 2g. The height between the water surface and the pipe outlet is 400 m. A discharge of 0.11 m3 /s is needed. What must the pressure in the tank be achieve such a flow rate? Assume a turbulent flow.