None Water fills the pipe AB such that the absolute pressure atA is 450 kPa. The inner diameter of the pipe is 55 mm.The density of the water is 1000 kg/m'. Acceleration dueto gravity is 9.81 m/s². (Figure 1)Figure0.3 m0.4 mIf the atmospheric pressure is 101 kPa, determine the resultant force the water and surrounding air exert on the cap at B.Express your answer to three significant figures and include the appropriate units.

FREE BODY DIAGRAM is a diagram of the system which represents all the forces acting on the system.…

Water fills the pipe AB such that the absolute pressure at A is 450 kPa. The inner diameter of the pipe is 55 mm. The density of the water is 1000 kg/m³. Acceleration due to gravity is 9.81 m/s². (Figure 1) Figure B 0.3 m -0.4 m If the atmospheric pressure is 101 kPa, determine the resultant force the water and surrounding air exert on the cap at B. Express your answer to three significant figures and include the appropriate units.

Water fills the pipe AB such that the absolute pressure at A is 450 kPa. The inner diameter of the pipe is 55 mm. The density of the water is 1000 kg/m³. Acceleration due to gravity is 9.81 m/s². (Figure 1) Figure B 0.3 m -0.4 m If the atmospheric pressure is 101 kPa, determine the resultant force the water and surrounding air exert on the cap at B. Express your answer to three significant figures and include the appropriate units.

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate and the smooth surface at B due to water pressure acting on the gate. Use =62.4lb/ft3 for water.
An unknown gas is flowing through a venturi meter whose diametersas shown. Gage pressures are measured 12.2 psia at the entranceand 11.8 psia at the throat. Take the density to be 0.105 lb/ft3.Determine the following: a) Neglecting friction, the volume flow rate of air b) If the pressure gauge is replaced with a manometer withmercury as its medium (SG=13.6), what will be the height ofthe mercury in inches? Draw the most possible orientationof the manometer and its fluid height.
An unknown gas is flowing through a venturi meter whose diametersas shown. Gage pressures are measured 12.2 psia at the entranceand 11.8 psia at the throat. Take the density to be 0.105 lb/ft3.Determine the following: A) Neglecting friction, the volume flow rate of airB) If the pressure gauge is replaced with a manometer withmercury as its medium (SG=13.6), what will be the height ofthe mercury in inches? Draw the most possible orientationof the manometer and its fluid height.
A tank contains a liquid of relative density 0.80. The height of the tank is 4, and the width of the tank is 2m. The tank is subjected to the acceleration of 5m/s^2 along a 30o inclined plane in the upward direction. Under this condition, there is no loss of liquid. determine the slope of free surface determine the pressure at presure
A closed tank rectangular in plane with vertical sides is 1.8m deep and contains water to a depth of 1.2m. Air is pumped into the space above the water until the air pressure is 35kN/m2. If the length of one wall of the tank is 3m, determine the resultant force on this wall and the height of the centre of pressure above the base
The curved surface given in the figure is defined by y = 3 x−−√x . Determine the horizontal force and its line of action applied by water on the curved surface. The width of the gate is b = 2.3 m. Take the density of water to be 1000 kg/m3. Height of the water is 5 m
A tank contains a liquid of relative density 0.80. The height of the tank is 4, and the width of the tank is 2m. The tank is subjected to the acceleration of 5m/s^2 along a 30o inclined plane in the upward direction. Under this condition, there is no loss of liquid. determine the slope of free surface determine the pressure at point A and point B
A tank of water 4 m deep receives a constant upwardacceleration a z . Determine ( a ) the gage pressure at the tankbottom if a z = 5 m 2 /s and ( b ) the value of a z that causes thegage pressure at the tank bottom to be 1 atm.
In the hydraulic jack shown, a force of 100 N is exerted on the small piston. Determine the upward force on the large piston. The area of the small piston is 65 cm2, and the area of the large piston is 950 cm2. If the small piston moves 12 cm, how far will the large move? Assume the oil to be incompressible.
he gage pressure of the air in the tank shown in the figure is measured to be 65 kPa. Determine the differential height h of the mercury column.
Q4: The hydraulic lift in a car repair shop has an output diameter of 30 cm and is to lift cars up to 2000 kg. Determine the fluid gage pressure that must be maintained in the reservoir.
The three reservoirs system contains water. If L1 = 2000 m, f 1= 0.013, D1 = 1m; L2 = 2300 m, f2 = 0.02, D2 = 0.60m; and L3 = 2500 m, f = 0.023, D3 = 1.20m. Compute Q3 in m3/s.