Water flows at 5m/s is passed through a tube of 2.5 cm diameter, it is found to be heated from 20degC to 60degC. The heating is achieved by condensing steam on the surface of the tube and subsequently the surface temperature of the tube is maintained at 90degC. Water properties are as follows: density=995kg/m3, kinematic viscosity=.657x10-6 m2/s, Pr=4.43, k=.628W/mK, cp=4178J/kgK. Determine the Reynolds number Round your answer to 2 decimal places. What is the thermal coefficient Round your answer to 2 decimal places. what is the heat absorbed by the water? Round your answer to 2 decimal places.

Water flows at 5m/s is passed through a tube of 2.5 cm diameter, it is found to be heated from 20degC to 60degC. The heating is achieved by condensing steam on the surface of the tube and subsequently the surface temperature of the tube is maintained at 90degC. Water properties are as follows: density=995kg/m3, kinematic viscosity=.657x10-6 m2/s, Pr=4.43, k=.628W/mK, cp=4178J/kgK. Determine the Reynolds number Round your answer to 2 decimal places. What is the thermal coefficient Round your answer to 2 decimal places. what is the heat absorbed by the water? Round your answer to 2 decimal places.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.20P

See similar textbooks

Similar questions

Water flows at 5m/s is passed through a tube of 2.5 cm diameter, it is found to be heated from 20 °C to 60 °C. The heating is achieved by condensing steam on the surface of the tube and subsequently the surface temperature of the tube is maintained at 90degC. Water properties are as follows: density=995kg/m3, kinematic viscosity=.657x10-6 m2/s, Pr=4.43, k=.628W/mK, cp=4178J/kgK. a) Determine the Reynolds number b) What is the thermal coefficient on question number c) what is the heat absorbed by the water?
This is a fluid machine question. Glycerin at 40'C with density of 1252 kg/m3 and viscosity of 0.27kg m.s is flowing through a 5-cm diameter horizontal smooth pipe with an average velocity of 3.5 m/s. Determine the pressure drop per 10 m of the pipe.
A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The water flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, What is the local heat flux (Q/A) at the end of the plate (k=0.86 W/m deg C, Re=3840000, and Pr=0.7)? Round your answer to 2 decimal places.
A 20 °C water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40 °C The water flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, What is the local heat flux (Q/A) at the end of the plate (k=0.86 W/m deg C, Re=3840000, and Pr=0.7)?
An coconut oil (considered as viscous fluid) must be pumped between two buildings in an agro-industrial plant through an AISI 304 stainless steel pipe spread on the ground that has an outside diameter of 22 cm and 110 m long. To facilitate pumping, the liquid will be heated to 40 ° C in order to reduce its viscosity. The oil flow rate will be 20 Kg / s and the specific heat will be 1300 J / Kg K. Determine the temperature drop that the liquid will experience along the pipeline under the following operating conditions:Ambient air temperature = 10 ° CWind speed = 14 m / sPipe surface temperature = 37 ° C
A 10mm diameter and 20m long smooth tube is maintained at a constant surface temperature. Water enters the tube at 25 °C with mass flow rate of 0.01 kg/s. Properties of water at average mean temperature are: K= 0.65W/m.K, dynamic viscosity = 0.486X10^-3 Kg/m.s, Pr = 3.12 The flow at the end of the pipe is ?
Air at 10 m/s is flowing over a cylinder of D=(15) cm and L = 1 m. Air has thermalconductivity 0.027 W/mK, kinematic viscosity 1.9*10-5 m2/s, and Prandtl number 0.72.Find the Nusselt number
Carbon dioxide is being pumped through a smooth pipe at the rate of 3×10-4 kmol/sec for a distance of 2000 m. Ifthe line is isothermal at 323.15 K and the pressure at the entry point is 750 ×103 Pa and at the exit point is 430×103 Pa, what diameter should the pipe has to ensure that the CO2 will be delivered to the end point with the pressure drop experienced. The viscosity of CO2 at 323.15 K is 1.45×10-5kg/m.s. One trial is sufficient given you tell us how you will proceed to achieve an accurate diameter estimate. Hint: for your initial guess, use D in the range of 0.01-0.02 m.
The clutch system shown in Fig is used to transmit torque through a 2-mm-thick oil film with ? = 0.38 N⋅s/m2 between two identical 30-cm-diameter disks. When the driving shaft rotates at a speed of 1200 rpm, the driven shaft is observed to rotate at 1125 rpm. Using appropriate software, investigate the effect of oil film thickness on the torque transmitted. Let the film thickness vary from 0.1 mm to 10 mm. Plot your results, and state your conclusions.
A 20degC water flows to 50cmx60cm flat plate with velocity of 6m/s . The flat plate surface temperature is maintained at 40deg C. The air flows parallel to the 50cm side of the plate. If the kinematic viscosity of water is 78x10-8 m2/s, at what length the flow become turbulent? If the average laminar heat transfer coefficient of water is 7740W/m2 degC, what is the overall heat transfer at the laminar section?
A 3 cm diameter and 50 cm long bar greased with lubricating oil of 5 x 10-4 m kinematic viscosity (SAE-30 oil at 20°C) is inserted into a horizontal tube with an internal diameter of 3.1 cm and pushed with a constant speed of 1 m/s. Determine the force to be exercised: Data provided: (image)
Water flowing in a straight cylinder tube with radius of 3mm, has a maximum velocity U0=15cm/s. If the density and viscosity of the water are 1000kg/m3 and 1.0 x 10 -3 (Pa.s), and the flow is fully developed with a profile of u=U0(1-(r/a)2), calculate the Reynold’s number of the flow; calculate the mass flow rate in units of kg/s in the tube If the tube has a length of 50cm, calculate the flow resistance force of the tube wall imposed to the flow.