Water flows at the rate of 0.09 ml/s in an upward direction through a sand sample with a coefficient of permeability of 2.7 x 10^-2 mm/s. The thickness of the sample is 120 mm and the area of cross-section is 5400 mm2. Taking the saturated unit weight of the sand as 18.9 kN/m3, determine the effective pressure in Pa at the bottom of the sample. Оa. 364 Оb. 910 О с. 728 O d. 182

Water flows at the rate of 0.09 ml/s in an upward direction through a sand sample with a coefficient of permeability of 2.7 x 10^-2 mm/s. The thickness of the sample is 120 mm and the area of cross-section is 5400 mm2. Taking the saturated unit weight of the sand as 18.9 kN/m3, determine the effective pressure in Pa at the bottom of the sample. Оa. 364 Оb. 910 О с. 728 O d. 182

Fundamentals of Geotechnical Engineering (MindTap Course List)

5th Edition

ISBN:9781305635180

Author:Braja M. Das, Nagaratnam Sivakugan

Publisher:Braja M. Das, Nagaratnam Sivakugan

Chapter11: Ground Improvement

Section: Chapter Questions

Problem 11.8P

See similar textbooks

Similar questions

Water flows at the rate of 0.09 ml/s in an upward direction through a sand sample with a coefficient of permeability of 2.7 × 10^–2 mm/s. The thickness of the sample is 120mm and the area of cross-section is 5400 mm2. Taking the saturated unit weight of the sand as 18.9 kN/m3, determine the effective pressure in Pa at the middle of the sample. a. 364 b. 910 c. 182 d. 728
Water flows at the rate of 0.09 ml/s in an upward direction through a sand sample with a coefficient of permeability of 2.7 × 10^–2 mm/s. The thickness of the sample is 120 mm and the area of cross-section is 5400 mm2. Taking the saturated unit weight of the sand as 18.9 kN/m3, determine the effective pressure in Pa at the bottom of the sample. a. 364 b. 728 c. 182 d. 910
A deposit of cohesionless soil with a permeability of 0.3 mm/s has a depth of 12 m with impervious ledge below. A sheet pile wall is driven into this deposit to a depth of 8 m. The wall extendsabove the surface of the soil, and a 3 m depth of water acts on one side. Sketch the flow net and determine the seepage quantity. a. 600 ml/s/meter length b. 300 ml/s/meter length c. 1200 ml/s/meter length d. 900 ml/s/meter length
For a falling a head permeability test, the following data were recorded. Length of soil specimen = 500 mm. Area of soil specimen = 16 cm2 Area of stand pipe = 0.97 cm2 Head difference at time t =0 is 760 mm. Head difference at time t = 6min. is 410mm. The test was conducted at a temp. of 20 ֯C. with a unit wt. of water equal to 9.789 kN/m3 and the viscosity of water at 20 ֯C is 1.005 x 10-3 N.8/m2 . Compute the hydraulic conductivity of the soil. Compute the absolute permeability of the soil. What is the head difference at time t = 4 min?
GEOTECHNICAL COMPLETE SOLUTION PLS For a falling-head permeability test, the following are given: length of specimen = 15.1 in., area of specimen = 3.9 in^2, and k = 0.0686 in./min. What should be the area in sq. in. of the standpipe for the head to drop from 25.1 to 12.6 in. in 8.9 min. ?
A deposit of cohesionless soil with a permeability of 0.3 mm/s has a depth of 12 m with impervious ledge below. A sheet pile wall is driven into this deposit to a depth of 8 m. The wall extendsabove the surface of the soil, and a 3 m depth of water acts on one side. Sketch the flow net and determine the seepage quantity. Provide a diagram a.600 ml/s/meter length b.300 ml/s/meter length c.900 ml/s/meter length d.1200 ml/s/meter length
A pumping test was carried out to determine the average permeability of a sand deposit 20 m thick overlying impermeable clay. The discharge from the pumping well was 12 x 10-3m3/s. Drawdowns in the observation wells located 15 m and 30 m from the centerline of the pumping well were 2.1 m and 1.6 m, respectively. Groundwater table was reached at 3.2 m below the ground surface. Determine the permeability of the sand. Estimate the effective grain size using Hazen’s equation.
Refer to the figure. If H1 = 1.94 m, H2 = 2.37 m, h = 1.c m, e =0.49, Gs = 2.67,area of the tank = 0.64 m2, and hydraulic conductivity of the sand (k) = 0.3d cm/sec. What is the upward seepage force per unit volume of soil?
49. A pumping test was made in a sand layer extending to a depth of 16m. The initial groundwater table was located 2m below the ground surface. Observation wells were sighted at distances 4m and 9.5m from the pumping well. Using a discharge of 0.4 cubic meters per hour, a steady level is attained at the pumping well. The measured drawdowns at the two observation wells are 2m and 0.25m respectively. Determine the coefficient of permeability of the soil.
A dense silt layer has the following properties: Void ratio = 0.76, SG= 2.59. Free ground water is 9.31m below the ground. Capillary action rise will reach 7.93m. The soil above capillary action rise is dry while within the zone, it is saturated at 53.13%. Determine the effective pressure (kPa) at a depth of 7.05m from the groind surface. Use stored value. Asnwer in 5 decimal places.
For a falling head permeability test, the following are given: length of specimen is 360 mm, area of specimen is 70 cm2 , and hydraulic conductivity of soil specimen is 0.165 cm/min. what should be the area of the stand pipe for the head to drop from 700cm to 360cm in 7 mins? compute the seepage velocity under the test condition if the soil specimen has a void ratio of 0.55 in cm/sec compute the head difference at time equal to 5 minutes?
The hydraulic conductivity of a sand at a void ratio of 0.62 is0.03 cm/sec. Estimate its hydraulic conductivity at a void ratioof 0.48.