Water flows from a large reservoir to aSharp-edgedentrance, K05smallerthrough5-cmdiameteroneStandard elbow,flanged, K 0.3smoothpiping system as shown infigure. Determine the elevation Z1 for atheD=Scm=4mflow rate of 6 l/s. The dynamic viscosity ofGate valve.fully openK =02Controlvolumeboundarywater is (0.001307 Pa.s).80 m-Exit, K, - 1.06

Given Flow rate, Q = 6 L/s Diameter, d = 5 cm Find Elevation, Z

Water flows from a large resePV through 5-cm diameter smaller one a smooth piping system as shown in the figure. Determine the elevation Z1 for a flow rate of 6 /s. The dynamic viscosity of water is (0.001307 Pa.s).

Water flows from a large resePV through 5-cm diameter smaller one a smooth piping system as shown in the figure. Determine the elevation Z1 for a flow rate of 6 /s. The dynamic viscosity of water is (0.001307 Pa.s).

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: 1. Locate the centroid of the shaded area shown -75 mm- in the figure 1. 50 mm 75 mm 75 mm 125 mm 50…

A: Answer: The location of centroid: X = 61.62 mm , Y = -8.73 mm

Q: 2015.2 2.4713 27 0.031 2182.4 3.4800 29.33 0.044 2416.9 4.9900 32.48 0.063 2693.1 7.5062 36.19 0.095…

A: Given Data To find “Since you have posted a question with multiple sub-parts, we will solve the…

Q: Compute the engine cap of fuel engine power plant with 72 82% gen efficiency and supercharge engine…

A: Given: Efficiency = 72.82% = 0.7282 Supercharge engine capacity = 227 kW

Q: 0,5- Water flows from a tank of large cross-sectional area through a pipe as shown. The…

Q: 4) A closed system that is based on the Carnot heat engine cycle uses 60 g of water vapor (steam) as…

Q: 20 sq mm 40 sq mm 10° W W= 40 kg stress AB = Stress AC

Q: The crank AB of the mechanism shown on the right is connected to a slider B which moves on the…

A: (b)

Q: 7. A composite wall consists of three materials, as shown in Figure 2. The inside wall temperature…

Q: An Otto cycle has an initial pressure of 100 kpa and has a pressure of 400 kpa after expansion. Find…

Q: What is the energy produced in MW per month of fuel

A: To determine Energy produced/month

Q: Evaluate the integral dy dx using polar coordinate

Q: A particle of mass m attached to a rigid support by a support of constant k. At equilibrium, the…

Q: (c) Figure Q2 (c) (i) shows a pulley system sketched with current velocities of block 1 and block 3…

A: The displacement of blocks are as shown below

Q: For the Vertical bend shown, find the yeaction foree and their direction. D=300 DsZoomm V, =Sm/s Pz…

Q: Lap Joint Questions The following questions all use this figure. Assume a bolt will be put in each…

A: Given: To find: Number of fasteners counted for calculating area of net cross section.

Q: Q1:Air enters a diffuser at 200 m/s with a pressure of 80 kPa and a temperature of -20°C. It leaves…

Q: The combustion chamber of a diesel power plant has a theoretical heat value of 102 K Joules in a…

A: Given:

Q: Q2: Liquid water at 20°C flows straight up 30 m. 1- How much power pump is needed if the mass flow…

A: Calculated how much power, the pump is needed.

Q: Saturated ammonia at a temperature of 50oF and a flow rate of 3 lbm/s enters a steady-state…

Q: 12. The spectral hemispherical absorptivity and irradiation profiles for an opaque surface are shown…

Q: An investment cost for the wind power system is RM 5000 with the annual maintenance costs are RM…

A: Given : D = 30 m P = 400 kWh v = 7.5 m/s ρ=0.602 kg/m3 To find : Efficiency

Q: 4-39. Determine the resultant moment produced by the two forces about point O. Express the result as…

Q: The forces shown form a couple. Replace the shown couple with an equivalent couple acting at points…

A: Magnitude of force that forms a couple, F= 20 lb Distance between the couple, d= 1+4+3= 8 ft…

Q: A solid round aluminum shaft has a maximum allowable shear stress of 80 MPa. The shaft is 10 cm in…

A: Given Diameter, d = 10 cm Length, L = 1 m G = 28 MPa Shear stress = 80 MPa…

Q: A rotating system consists of four particles, each of mass M= 0.75 kg, fixed at distances from the…

Q: A system consists of 2 kg of water at 100°C and 1 bar. Determine the exergy, in kJ, if the system is…

Q: Consider two cases involving parallel flow of dry air at V=V= 2.5 m/s, T∞=45°C, and atmospheric…

Q: Question 2: A Pelton wheel turbine is used in a hydroelectric plant to generate electric power. In…

A: The velocity diagram for the symmetrical blade of a Pelton wheel is given below,

Q: Consider the special steel spring in the illustration. 1) Find the pitch, solid height, and number…

Q: Calculate the forces in members BC, BE, and EF. Solve for each force from an equilibrium equation…

A: Given :- To Find:- Forces in the members BC, BE and EF Sign Convention :- Positive - Tensile…

Q: Convert the polar function r = tan20 to cartesian.

Q: The 150-lb car of an amusement partk ride is connected to a rotating telescopic boom. When r = 15…

Q: The top surface of the passenger car of a train moving at a velocity of 115 km/h is 2.8 m wide and 8…

Q: al metacentric height, and (b) the f sea water is 10. 045 N/m3

Q: The plate of a record player with a moment of inertia of 0:015 kg m2 rotates freely at 33 rpm. If…

Q: full journal bearing with 140 mm diameter and 70 mm length supports a radial load of W. For a…

Q: Q: compute the total elongation caused by an axial load of 100KN applied to a circular bar, tapering…

A: Given:P=100 KNL=10 mD1=40 mmD2=120 mmE=200 GPa

Q: A helical compression spring is wound using 2.5 mm diameter music wire. The spring has an outside…

Q: Reservoir engineers transfer a crude oil with at 30 °C, and 9 kPa, and 200 m3 volume to tank by…

Q: Q3/ A 10-cm length of platinum wire 0.5 mm in diameter is placed horizontally in a container of air…

Q: 5 km. The wing has a NACA 65-210 A small aircraft is flying at steady level flight at an altitude…

Q: Value for 'D' in fatigue diagram above? (MPa) - {1DP} Your answer Value for 'E' in fatigue diagram…

A: A - yield strength B - alternating fatigue limit C - stress amplitude D - mean stress

Q: a volume of 0.5 m² ence environment f pecific exergy of the

Q: The man in Fig. 14-15a pushes on the 50-kg crate with a force of F= 150 N. Determine the power…

A: The power supplied by the man is 37.44 Watt.

Q: Gas and Themal Combined cyde power plant generates total power output equal to 212 MW and 208 MW…

Q: An athlete of 60 kg and 1.70 m tall performs the ring exercise called "the Christ", in which he…

A: Given : To find : R and β

Q: An air standard engine has a compression ratio of 15 and a cut off ratio of 3. If the intake air…

Q: A Carnot power cycle uses water as the working fluid. The boiler operates at a pressure of 2000 kPa…

A: Fig: T-S diagram From Steam table of pressure At P4=2000kPa(Saturated Vapour) h4=2798.3 kJ/kg…

Q: The thin uniform bar AB of mass m and length L hangs from a wheel at A, which m freely on the…

Q: Determine the magnitude of the pin force at A. Assume W - 520 lb, a-3.9 ft, b-3.1 ft.r-7 in.

Concept explainers

Properties of Fluids

The term fluid represents a type of substance that can easily change its shape under any external pressure/force and can flow. Fluids can acquire any shape in which it is stored and can resist normal stresses but cannot resist shear stress in rest condition. Whenever external shear stress is applied to fluids, it starts to flow. The fluids may be liquid or gas. Example- water, air, etc.

Question

Water flows from a large reservoir to a
Sharp-edged
entrance, K05
smaller
through
5-cm
diameter
one
Standard elbow,
flanged, K 0.3
smooth
piping system as shown in
figure. Determine the elevation Z1 for a
the
D=Scm
=4m
flow rate of 6 l/s. The dynamic viscosity of
Gate valve.
fully open
K =02
Control
volume
boundary
water is (0.001307 Pa.s).
80 m
-Exit, K, - 1.06

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The above pipe is exchanged for a parallel pipe with a cross sectional area of 0.3m2 and is 20 m long, with a surface roughness coefficient of 0.005. The dynamicviscosity of the water is 1.002 x 10-3 Ns/m. Find the Reynold’s number of the flowand use Haarland’s formula to find the friction coefficient and Darcy’s formula todetermine the frictional pressure loss. Then determine the pressure at the outlet ofthe pipe.
(a) Prove that the loss of pressure head for the viscous flow through a circular pipe is givenby h. (b) Determine (i) the pressure gradient, (ii) the shear stress at the two horizontal parallelplates, and (iii) the discharge per meter width for the laminar flow of oil with a maximumvelocity of 1.5 m/s between two horizontal parallel fixed plates which are 80 mm apart. Takeviscosity of oil as 1.962 Ns/m2.
A petroleum product of viscosity 0.5 m Ns/m2 and density 700 kg/m3 is pumped througha pipe of 0.15 m diameter to storage tanks situated 100 m away. The pressure drop alongthe pipe is 70 kN/m2. The pipeline has to be repaired and it is necessary to pump the liquid by an alternative route consisting of 70 m of 200 mm pipe followed by 50 m of 100 mm pipe. If the existing pump is capable of developing a pressure of 300 kN/m2, will it be suitable for use during the period required for the repairs? Calculate the pressure drop for the alternative pipe system. Take the roughnessof the pipe surface as 0.05 m
Oil of specific gravity 0.70 and dynamic viscosity of 0.05Pa-s flows at a rate of 100lit/sec through a 80m of 150mm diameter pipe. If the head lost is 4m, determine the reynolds number, maximum velocity in m/s, maximum shear stress in Pa , Velocity 40mm from centerline of pipe in m/s.
SAE 30W oil at 20 ° C flows through the 9-cm-diameterpipe in Fig. P4.87 at an average velocity of 4.3 m/s. ( a ) Verify that the flow is laminar. ( b ) Determine the volumeflow rate in m 3 /h. ( c ) Calculate the expected reading hof the mercury manometer, in cm.
the nord stream 2 is a pipeline network from used to pump and transport Russian oil to germany. 29286 gallons of oil can be transported per minute through the pipes with an average inside diameter of 50 inches. Given the oil ttranported has a density of 57.99 lbm/ft3 and a viscosity of an 0.0069625 lbm/fts. what is the reynolds number of flow?
The velocity through the centre-line of a 150 mm diameter pipe conveying oil under laminar flow conditions is 3 m/s. The viscosity of the oil is 1.2 poises and its density if 900 kg/m3 . Confirm that the flow is laminar and determine (a) the quantity flowing in dm³/s, and (b) the shear stress in the oil at the pipe wall in N/m²
Water flows through the following circular pipe with a diameter of 30 mm at a speed of 3 m/s, what is the hydrodynamic entry length? The water dynamic viscosity is 1.002×10-3kg/(m⋅s).
Density of oil = 900kg/m3kinematic coefficient of viscosity ν = 0.00001m2/s fluid flows at qv = 0. 2m3/s Length = 500 m oDimaeter = 200-mm Determine: (a) the head loss and(b) the pressure drop if the pipe slopes down at 8 in the flow direction.
A pipe whose axis is horizontal, is full of water in motion. At a section A, the velocity of water is recorded as 54000dm/hrandd the pressure is equilavent tp 14.07m of water. if the pipe tapers gradually from 150mm diameter to A to 100mm diameter at B. determine the preesure at B.
Determine the size of a galvanised iron pipe needed to transmit water a distance of 180 m at 0.085 m> /s with a loss of head of 9 m. (Take kinematic viscosity of water n=1.14 x 10°m? /s, and the average surface roughness for galvanised iron = 0.15 mm).
Water is flowing in a horizontal smooth plastic pipe with a velocity of 20mm/s. What is the pressure difference between the point of entry to the exit of the 1m length of plastic pipe with a diameter of .15m if the dynamic viscosity is .0010016 Ns/m² ? ( hint: apply Bernoulli's energy equation, combined with Darcy Weisback)