Water flows on a straight 150 m pipe, 600 mm in diameter. The velocity of flow 1.8 m/s. Pipe thickness is 16 mm. Bulk modulus of elasticity of water is 2.2 x 109 Pa. Modulus of elasticity of pipe material is 1.4 x 1011 Pa. Determine the celerity of pressure wave of water. O 1177 m/s 1256 m/s O 1421 m/s O 1382 m/s

Water flows on a straight 150 m pipe, 600 mm in diameter. The velocity of flow 1.8 m/s. Pipe thickness is 16 mm. Bulk modulus of elasticity of water is 2.2 x 109 Pa. Modulus of elasticity of pipe material is 1.4 x 1011 Pa. Determine the celerity of pressure wave of water. O 1177 m/s 1256 m/s O 1421 m/s O 1382 m/s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A vertical pipe 3 ft in diameter and 30 ft long has a pressure head at the upper end of 22 ft. of water. When water flows through it with mean velocity of 15 fps, the friction loss is 6 ft. Find the pressure head in ft. at the lower end of the pipe when the flow is upward. a.69.6b.46.0c.89.6d.58.0
(b) A horizontal pipe is diverted upwards with an angle of 25 degrees. Water enters with a velocity of 4.5 ms-1 and exits upwards. The pipe entrance has a diameter of 200 mm and increases two times at the outlet. The inlet gauge pressure reads 80 kPa. If the difference vertical distance between inlet and outlet is 0.4 m, calculate the magnitude and direction of the resultant force on the pipe bend. Neglect energy losses and take the volume of water to be 0.18 m3
A vertical pipe 3 ft in diameter and 30 ft long has a pressure head at the upper end of 22 ft. of water. When water flows through it with mean velocity of 15 fps, the friction loss is 6 ft. Find the pressure head in ft. at the lower end of the pipe when the flow is downward. a. 58.0 b. 46.0 c. 69.6 d. 89.6
Refer to Fig. P5.4. Water at 10°C flows up AB (5 m long, 40 mm diameter),then along BC (3 m long, 30 mm diameter). The measured pressure at A is 275kPa. (a) Find the pressure at C if the flow rate is 2.0 L/s. Neglect pipe frictionand energy losses. 6) Repeat for the same flow rate in the opposite direction.Table A.1 for water at 10°C: y = 9.804 kN/m².Vertical
Water flows through a horizontal pipe with a cross-sectional area of 5m^2 at a speed of 6L/sec. With a pressure of 3atm at point A. At point b, The cross-sectional are is 3m^2a) what is the speed of the water at point b.b) calculate the pressure at point b.
Three riveted steel pipes (e = 0.006 ft) are connected in series. Find the flow throughthem if the pipe diameters and lengths are D1: 24 in, D2: 18 in, D3: 20 in, L1: 1500 ft, L2:1600 ft, and L3: 2000 ft and the total head loss of the system is 145 ft. Use the DarcyWeisbach equation and assume complete turbulence. Minor losses (entrance, exit, etc.) shallbe considered.• Determine f for each pipe from Figure 6.9 or Moody Diagram.• Attached the diagram that is used to find f’s and show your work on the diagram;and• Assume both expansion and contraction have an angle of  = 40
The flowrate of the flow is 0.20 + a/10 m3 /s in a pipe placed on a horizontal plane. The pipe diameters are D1= 0.30 m and D2= 0.20. Please find the force acting to the pipe by the flow. The gauge pressure at (1) is p1 =200 + b*10 kN/m2 . (g=9,81 m/s2, g=10kN/m3 ) a= 4 b=3
Water flows from a large reservoir at the rate of 0.0137 m3/s through the system shown in the Fig. below. Calculate the pressure at B. NB: Use f = 0.017 (friction factor) and fT = 0.010 in zone of complete turbulence. Hint: Include minor losses, assume K = 1.0 for the inlet or entrance and use the applicable appendix at the back of the textbook to obtain the pipe parameters.
Fluid mechanics, i need solutions in 10 minutes please. MCQ/The submerged sector gate AB shown in the figure is 1/9 of a circle radius 4 m. The length of the gate is 10 m. Determine the horizontal component of water pressure acting on the gate. A-262.874 kN B-162.328 KN C-324.260 KN D- 448.161 KN E- 591.263 KN F-392.273 kN G- 89.207 kN H-536.078 KN I-208.119 KN J- 490.984 kN K- 127.908 KN L- 113.001 KN
A certain part of cast iron piping of a water distribution involves a parallel sectionas shown in Figure Q2(b). Both parallel pipes have a diameter of 30 cm, and theflow is fully turbulent. One of the branches (pipe A) is 1500 m long while theother branch (pipe B) is 2500 m long. The flowrate through pipe A is 4 m3/s. Ifthe friction factor of pipe A and pipe B are the same, determine flowrate throughpipe B. Assume the water temperature is 150C and disregard minor losses
Water discharges from a large tank through a pipe 40 mm diameter and length of 55 m that is sharp at entrance. The level of water in the tank is 3 m above the centre end of the pipeline work. Consider all the minor losses and the co-efficient of friction (ƒ = 0.008) for the pipe. Determine the velocity in m/s in the pipeline.
Fluid mechanics, i need solutions in 10 minutes please. Q/Q2 The 4 -m- diameter circular gate of Fig. E2.6a is located in the inclined wall of a large reser voir containing water (y = 9.80 kN / m³). The gate is mounted on a shaft along its horizon tal diameter. For a water depth of 10 m above the shaft determine: (a) the magnitude and lo cation of the resultant force exerted on the gate by the water, and (b) the moment that would have to be applied to the shaft to open the gate.