Read the question carefully and give me right solution according to the question.Note: carefully answer with part B 2. Water flows steadily with negligibleviscous effects through a pipe shown onthe right. It is known that the 4-in.diameter section of this-walled tubing willcollapse if the pressure within it becomesless than 10 psi below atmospheric4 ft4-in.-diameter thin-walled tubingpressure. (a) Determine the maximumvalue that h can have without causingcollapse of the tubing. (b) Draw and labelthe energy and hydraulic grade lines forthis problem.6 in.

Answered: Image /qna-images/answer/c40e8328-523e-4fc2-aebb-0208a70a8a83.jpg

Answered: Water flows steadily with negligible…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A reducing bend with an inlet diameter of 200 mm and exit diameter of 150 mm bends 40 degreesupwards. The water velocity and corresponding pressure at the inlet to the band is 4, 5 m/s and 70 kParespectively. Determine the weight flow, the water flow velocity at the exit to the bend, the bend exitpressure if the friction head loss through the bend section is 2 m and the magnitude and direction ofthe resultant force flowing through the bend.
Knowing that a U-tube contains water, what will be the difference between the water levels in each of its branches, if we blow air at a speed of 15 m / s over one of these branches, tangent to its opening?
A liquid of specific gravity 1.3 flows in a pipe at a rate of 800 l/s, from point1 to point 2 which is 1 m above point 1. The diameters at section 1 and 2 are 0.6 mand 0.3 m respectively. If the pressure at section 1 is 10 bar, determine the pressureat section 2.
Water at 65 degrees Celsius is flowing horizontally at a rate of 84.1 m^3/hr in a pipe. It enters a 150-mm 90 degree elbow and is diverted upwards into a connecting pipe. The diameter of the outlet is 85mm. If the pressure just before the elbow is 95 kPa, determine the magnitude and direction of the force necessary to keep the elbow in place. Assume frictional losses in the elbow are negligible.
A reducing elbow is used to deflect water flow at a rate of 14 kg/s in a horizontal pipe upward 30° while accelerating it The elbow discharges water into the atmosphere. The cross-sectional area of the elbow is 113 cm2 at the inlet and 7 cm2 at the outlet. The elevation difference between the centers of the outlet and the inlet is 30 cm. The weight of the elbow and the water in it is considered to be negligible. Determine (a) the gage pressure at the center of the inlet of the elbow and (b) the anchoring force needed to hold the elbow in place.
A pipe whose axis is horizontal, is full of water in motion. At a section A, the velocity of water is recorded as 54000dm/hrandd the pressure is equilavent tp 14.07m of water. if the pipe tapers gradually from 150mm diameter to A to 100mm diameter at B. determine the preesure at B.
Assume an ideal fluid with mass density of 900kg/cu.m. The pressure and velocity at section 1 are 100kPa and 10 m/s, respectively. The velocity at section 2is 20 m/s. (a) Determine the reading on the manometer.(b) If the downstream piezometer was replaced with aPitot tube, what would be the manometer reading?Comment on the practicality of these arrangements.
A 90° elbow in a horizontal pipe is used to direct water flow upward at a rate of 40 kg/s. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference between the centers of the exit and the inlet of the elbow is 50 cm. The weight of the elbow and the water in it is considered to be negligible. Determine (a) the gage pressure at the center of the inlet of the elbow and (b) the anchoring force needed to hold the elbow in place. Take the momentum-flux correction factor to be 1.03 at both the inlet and the outlet.
Water is flowing upward through a tapering pipe of height 1 m at the rate of 0.28 cumec. Thediameters at the lower and upper ends of the pipe are 300 mm and 600 mm, respectively. If pressure atthe lower end of the pipe is 0.981 bar, determine the force exerted on the tapering pipe and itsdirection. Neglect the losses of energy and the weight of the pipe.
O1: A stream of water of diameter d = 0.1 m flows steadily from a tank of diameter D= 1.0 m. Determine The Weight Flowrate, needed from the inflow pipe if the water depth remains constant, 0 — d=010m
If a jet is inclined upward 30O from the horizontal, what must be itsvelocity to reach over a 3-m wall at a horizontal distance of 18 m,neglecting friction?
We have two connected tanks with surface areas A1 and A2, both open to the atmosphere, filled with water of density ρ. Point 1 is at the water level height h1 and point 2 is at height d, with the water level of the second tank at h2. Knowing that the system is not in equilibrium, and given the fluid velocities at these points as v1 and v2 respectively, calculate the pressure at these points and determine the Bernoulli's constant for them. Lastly, is the problem solvable given the provided conditions?

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS