Q.6Water is coming out to the atmospherefrom a converging channel with a velocityof 5 m/s as shown in the figure. At sectionA, a cylinder of 10 cm diameter containinga friction-less piston attached to a springhaving spring constant 500 N/m isconnected. The cross-section diameterof the channel at A and B is 2 m and 1m respectively. Due to the flow the spring iscompressed by an amount of2mIm5m/sA184 cm368 сmC36.8 сm18.4 cm

Answered: Image /qna-images/answer/2748dfc9-b25e-412b-b48f-a51e438e0db4.jpg

Answered: Water is coming out to the atmosphere…

Water is coming out to the atmosphere from a converging channel with a velocity of 5 m/s as shown in the figure. At section A, a cylinder of 10 cm diameter containing

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A lawn sprinkler with three identical arms is used to water a garden by rotating in a horizontal plane by the impulse caused by water flow. Water enters the sprinkler along the axis of rotation at a rate of 45 L/s and leaves the 1.5-cm-diameter nozzles in the tangential direction. The bearing applies a retarding torque of T0 = 40 N·m due to friction at the anticipated operating speeds. For a normal distance of 40 cm between the axis of rotation and the center of the nozzles, determine the angular velocity of the sprinkler shaft.
A 90" elbow is used to direct water flow at a rate of 0,025 m3/s in a horizontal pipe upward. The diameter of the entire elbow is 10 cm. The elbow discharges water into the atmosphere, and thus the pressure at the exit is the local atmospheric pressure. The elevation difference betwoen the centers of the exit and the inlet of the elbow is 35 cm. The weight of the elbow and the water in it is considered to be negligible. Determine the anchoring force needed to hold the elbow in place A) 27 N 3433.5 N C) 79.5 N D) 132. 9 E) 106. 5 N
A reducing elbow is used to deflect water flow at 25 L/s in a horizontal pipe upward by an angle of=45° from the flow direction while accelerating it. The elbow discharges water into the atmosphere. The diameter of the elbow is 15 cm at the inlet and 5 cm at the exit. The elevation difference between the center of the exit and inlet is 40 cm. The mass of the elbow and the water in it is 40 kg. Determine the anchoring force needed to hold the elbow in place, assuming a momentum-flux correction factor of 1.03.
Blowers are used in wastewater treatment plants to assist microorganisms in degrading pollutants. The impeller of a centrifugal blower has a radius of 15 cm and a blade width of 6.1 cm at the inlet, and a radius of 30 cm and a blade width of 3.4 cm at the outlet. The blower delivers atmospheric air at 20°C and 95 kPa. Disregarding any losses and assuming the tangential components of air velocity at the inlet and the outlet to be equal to the impeller velocity at respective locations, determine the volumetric flow rate of air when the rotational speed of the shaft is 800 rpm and the power consumption of the blower is 120 W. Also determine the normal components of velocity at the inlet and outlet of the impeller.
A 90° elbow is directs water upwards into the atmosphere from a horizontal pipe with a diameter of 12 cm that is flowing at 20 L/s. The elevation difference between the centers of the exit and the inlet of the elbow is 35 cm. If the weight of the elbow and the water in it are negligible, and assuming a momentum-flux correction factor of 1.03, determine the anchoring force needed to hold the elbow in place.
Water flows through a 90 degree elbow connected to a pipe with diameter of 1.5 cm. At inlet pressure is 183kPa while at outlet water is discharged at a velocity of 200 ft/s to the atmosphere through a diameter of 5cm. Determine the force necessary to keep the elbow in place.
A 3-in diameter horizontal water jet having a velocity of 140 ft/s strikes a curved plate, which deflects the water 180 degrees at the same speed. Ignoring the frictional effects, determine the force required to hold the plate against the water stream. Please no conversion need it, only the 3in into .25feet, please. for me, I got 3.71KN on the x-axis.
A jet of water with velocity 35 m/s strikes a series of radial curved vane mounted on a wheel which is rotating at 200 rpm. The jet makes an angle 30° with the tangent to the wheel at inlet, and leaves the wheel with a velocity 5 m/s at angle of 140° to the tangent to the wheel at the outlet. The outer and inner radii of the wheel are 70 cm and 35 cm, respectively. A. Determine the Inlet Vane Angle, in degrees.
The impeller of a centrifugal blower has a radius of 15 cm and a blade width of 6.1 cm at the inlet, and a radius of 30 cm and a blade width of 3.4 cm at the outlet. The blower delivers atmospheric air at 20°C and 95 kPa. Disre- garding any losses and assuming the tangential components of air velocity at the inlet and the outlet to be equal to the impeller velocity at respective locations, determine the volu- metric flow rate of air when the rotational speed of the shaft is 800 rpm and the power consumption of the blower is 120 W. Also determine the normal components of velocity at the inlet and outlet of the impeller.
Airstream flows in a converging duct from a cross-sectional area A1=50cm2to across-sectional area A2=40cm2. If T1=300K, P1=100kPa, and V1=100m/s, find area throat, velocity in throat and temperature in throat.
Water at 20 ° C flows through a 5-cm-diameter pipe that hasa 180 °vertical bend, as in Fig. P3.43. The total length ofthe pipe between flanges 1 and 2 is 75 cm. When the weightflow rate is 230 N/s, p 1 = 165 kPa, and p 2 = 134 kPa.Neglecting pipe weight, determine the total force that thefl anges must withstand for this flow.
Water enters a two-armed lawn sprinkler along the vertical axis at a rate of 75 L/s, and leaves the sprinkler nozzles as 2-cm diameter jets at an angle of ? from the tangential direction, as shown. The length of each sprinkler arm is 0.52 m.For the specified flow rate, investigate the effect of discharge angle ? on the rate of rotation n. by varying ? from 0° to 90° in increments of 10°. Plot the rate of rotation versus ?, and discuss your results.