Answered: Water is falling from a height of 100m.…

Name: Water is falling from a height of 100m. If the energy beforethis wate
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: Water is falling from a height of 100m. If the energy beforethis water falls is all converted to heat without loss, what isthe rising temperature of the water at what temperature?G=1kg, mc=1kg

Engineering

Mechanical Engineering

Water is falling from a height of 100m. If the energy before this water falls is all converted to heat without loss, what is the rising temperature of the water at what temperature? G=1kg, mc=1kg

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter8: Centroids And Distributed Loads

Section: Chapter Questions

Problem 8.122P: The 12-ft wide quarter-circular gate AB is hinged at A. Determine the contact force between the gate...

See similar textbooks

Similar questions

The density of a floating body can be determined by tying weights to the body until both the body and the weights are completely submerged, and then weighing them separately in air. Consider a wood log that weighs 1540 N in air. If it takes 34 kg of lead (r 5 11,300 kg/m3) to completely sink the log and the lead in water, determine the average density of the log.
A tank contains a liquid of relative density 0.80. The height of the tank is 4, and the width of the tank is 2m. The tank is subjected to the acceleration of 5m/s^2 along a 30o inclined plane in the upward direction. Under this condition, there is no loss of liquid. determine the slope of free surface determine the pressure at presure
The truck carries an open rectangular container that is 3.9m wide, 3.0m deep and 5.0m long, contains oil of density 811kg/m³ to a depth of 2.1m. If it has a constant acceleration of 6.9m/s². Determine the total force(in kN) acting at the rear wall of the container.
plzzzzzzz help What is the minimum Block mass (kg) that is required to open the gate A-B? The density of water is 1000 kg/m3 and the density of the block is 8000 kg/m3. The specific gravity of oil is 0.9. The depth of the gate is not required. The external force that effects the gate at point A is Fe=3000 N, while the hydrostatic force Fh=9313.8 N
The curved surface given in the figure is defined by y = 3 x−−√x . Determine the horizontal force and its line of action applied by water on the curved surface. The width of the gate is b = 2.3 m. Take the density of water to be 1000 kg/m3. Height of the water is 5 m
Determine the volume of the body (s=3.0) that is required to keep the gate in the position indicated in the figure. The gate is 2.40m wide and 4.2m long.
A tank contains a liquid of relative density 0.80. The height of the tank is 4, and the width of the tank is 2m. The tank is subjected to the acceleration of 5m/s^2 along a 30o inclined plane in the upward direction. Under this condition, there is no loss of liquid. determine the slope of free surface determine the pressure at point A and point B
A 50-kg friction-less piston fits inside a 30-cm-diameter vertical pipe and is pulled up to a height of 6.1 m. The pipe's lower end is immersed in water, and the atmospheric pressure is 100 KPaa. The graviattional acceleration is 9.45 m/s². Determine: (a) the force required to hold the piston at the 6.1-m mark; (b) the pressure of the water on the underside of the piston.
A 10-kg block slides down a smooth inclined surface as shown in below figure . Determine the terminal velocity of the block if the 0.1-mm gap between the block and the surface contains SAE 30W oil at 60
Balloons are often filled with helium gas because it weighs only about one-seventh of what air weighs under identical conditions. The buoyancy force, which can be expressed as Fb = ρairgVballoon, will push the balloon upward. If the balloon has a diameter of 12 m and carries two people, 85 kg each, determine the acceleration of the balloon when it is first released. Assume the density of air is ρ = 1.16 kg/m3 , and neglect the weight of the ropes and the cage.
What is the maximum liquid water depth for a laminar flow if the flow speed is 0.01 m/s? (The density of water is still 1000 kg/m3, and it has a viscosity of 0.001 kg/(m*s).)
A fan is used to force air having a temperature of 20°C through the 200-mm diameter galvanized sheet metal duct. Determine the required power output of the fan if the length of the duct is 150 m and the flow is to be 0.15 m3/s. Take f=0.023, density of air = 1.202 kg/m3, and kinematic viscosity of air = 15.1×10-6 m2/s.