Water is transferred from one reservoir to another through centrifugal pump as shown in the figure, The ietion n pfrom the reservoirs to pump inlet is 12 A. The water vapour pressure is 66 Tbe and atmospherie prosiare is 147 p theavailable for this piping system. (Density ofr water is 62.24 Thm/ and viscosity is 0.001307Kg/m.a)3)Z3ReservoirZ3-Z1ValveReservoir ReservoirValve22ValvePumpOA 56O8 43 tOC 15OD 10.8

Answered: Image /qna-images/answer/e328e7d6-ab77-4c64-8257-a888155f8703.jpg

Water is transferred from one reservoir to another through centrifugal pup shown in the figure. The eletion n dI20 from the reservoirs to pump inlet is 12 A. The water vapour pressure is 66 The and atmospherie proiare la 14 p r the had avallable for this piping system. (Density of water is 62.24 bm/ and viscosity is 0.001307Kgm.a)

Water is transferred from one reservoir to another through centrifugal pup shown in the figure. The eletion n dI20 from the reservoirs to pump inlet is 12 A. The water vapour pressure is 66 The and atmospherie proiare la 14 p r the had avallable for this piping system. (Density of water is 62.24 bm/ and viscosity is 0.001307Kgm.a)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In Fig. the pipe entrance is sharp-edged. If the fl ow rateis 0.004 m3/s, what power, in W, is extracted by the turbine?
In a liquor-bottling plant erected at a site 1 km above sea level (Patm=0.898 bar and temperature 8.7°C) where a centrifugal pump discharges 20 l/s of water against a head of 28 m while the cavita on parameter of the pump a=0.5. Where should the pump inlet location be in m with respect to the water surface.
A four-stage centrifugal pump has four identical impellers, keyed to the same shaft. The shaftis running at 400 r.p.m. and the total manometric head developed by the multistage pump is 40m. The discharge through the pump is 0.2 m*3/s. The vanes of each impeller are having outlet angle as 45°. If the width and diameter of each impeller at outlet is 5cm and 60 cm respectively, Find the manometric efficiency.
Question 2) The centrifugal pump in the figure is in his preference Passing water at 25°C from the tank through the 1.22 m exchange store pumping. Inner diameter of the suction channel is 101.6 mm, in total it is 0.0306 and its length is 3.2 m. It the local coefficients of the user in the pipe are 7.4. If the pump works at a flow rate of 109 m3/h ENPY=1.52 is m. Does the pump work without cavitation at this flow? Show the calculation. For water, p=997 kg/m3 and Pb=3.169 kPa. Piping system at the entrance (Suction pipe) pump 22 Patm=101.3 kPa and 0.2=1.05. van
A pump draws 30-°C water at 0.5 liters per second from a pressurized tank where the air pressure above the water is . The required NPSH of the pump is 8.2 m. The suction pipe has a diameter of 4 cm, total length of 5.2 m, and friction factor of 0.005. If the pump has a suction lift of 3.8 m, will cavitation occur? Use the properties of sat. liquid water at 30°C. A. YES, CAVITATION WILL OCCUR B. NO, CAVITATION WILL NOT OCCUR
A four-stage centrifugal pump has four identical impellers, keyed to the same shaft. The shaft is running at 400 r.p.m. and the total manometric head developed by the multistage pump is 40m. The discharge through the pump is 0.2 m*3/s. The vanes of each impeller are having outlet angle as 45°. If the width and diameter of each impeller at outlet is 5cm and 60 cm respectively, Find the manometric efficiency.
Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m
The 32-in pump in Fig. is used at 1170 r/min in asystem whose head curve is Hs (ft) = 100 + 1.5Q2, with Qin thousands of gallons of water per minute. Find the dischargeand brake horsepower required for (a) one pump,(b) two pumps in parallel, and (c) two pumps in series.Which configuration is best?
The owners of a smallholding water their vegetable garden using collected rainwater from atank. Thetankhasadiameterofbm,itisam tall and sits on a 6 m tall stand. The inner diameter of the hose is c cm, and the hose is (20 +5d) m long. If the tank was initially filled to the brim, how long will it take before the tank is empty? Assume that there is a single ball valve (K = 0.05) in the line, and that the spray nozzle has a hole diameter that is 20 % of the diameter of the hose. You may ignore all other losses in the nozzle. a = 9 b = 8 c = 7 d = 1 Hint: Use an Excel spreadsheet or C program for the calculations.
A pump has a suction condition of 50mm Hg vacuum pressure, 100mm diameter pipe and discharged condition of 250kpa at, 90mm diameter. The discharge tank is 50m elevation and the suction is 5m below the pump center line. If the discharge is 0.20 m3/s, find the pump efficiency for 260kw brake power. Answer: 74.32%
A pump receives water from a tank. If the pump needs 24 n of NPSHA, how high must the water level be above the pump centerline if the water saturated at 1724 kpa ? The friction loss in the pipe averages 0.3m for each 6m height and the flow is 23 lps in a 15024 cm id pipe.
In Fig. is shown a plot of pump net head as a function of pump volume flow rate, or capacity. On the figure, label the shutoff head, the free delivery, the pump performance curve, the system curve, and the operating point.