Select one:a. 108.28b. 401.81c. 310.93d. 694.16e. 990.93 Water (viscosity of 0.001 kg/m.s and density of1000 kg/m ) is to be pumped through 50 m of pipefrom lower reservoir to a higher reservoir at a rateof 0.2 m /s. If the pipe is cast iron of diameter 123.cm and the pump efficient is =0.34%, the majorhead loss inside the pipe is ¼ of the velocity headwhat horsepower pump is needed? Hint: considerthe abrupt expansion only as a minor loss.32 mL = 50 mPump

Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m ) is to be pumped through 50 m of pipe from lower reservoir to a higher reservoir at a rate 3 of 0.2 m /s. If the pipe is cast iron of diameter 12 cm and the pump efficient is =0.34%, the major head loss inside the pipe is ¼ of the velocity head what horsepower pump is needed? Hint: consider the abrupt expansion only as a minor loss.

Water (viscosity of 0.001 kg/m.s and density of 1000 kg/m ) is to be pumped through 50 m of pipe from lower reservoir to a higher reservoir at a rate 3 of 0.2 m /s. If the pipe is cast iron of diameter 12 cm and the pump efficient is =0.34%, the major head loss inside the pipe is ¼ of the velocity head what horsepower pump is needed? Hint: consider the abrupt expansion only as a minor loss.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows through a venturi meter whose inlet diameter is 31 cm and throat diameter is 19 cm. The pressure at the inlet is 755kPa and at the throat 550 kPa. Determine the discharge in cumecs. Neglect head loss.
If the inner diameter of the penstock that deliver water form the dam to the hydroelectricpower plantis 90 cm and the water flows inside itat a rate of 10 L/s. (?=0.0131?????)a.Define the type of flowinside the penstockusing Reynolds numberequation.b.Explain the significance of the information we get from Reynolds number equation.
The pump , running at 880 r/min, is topump water at 20°C through 75 m of horizontal galvanizediron pipe. All other system losses are neglected. Determinethe flow rate and input power for (a) pipe diameter =20 cm and (b) the pipe diameter found to yield maximumpump efficiency.
water flows through a horizontal venturyi meter whose inlet diameter is 33 cm. and throat diameter is 21 cm. the pressure at the inlet is 775 kpa and at the throat is 584 kPa. determine the discharge in L/s. neglect head lost.
A pipe of 0.25 m diameter carries water at the rate of 7.2 m3/s.The pressure head at the entry of the venturimeter, used to measure the flow rate in the pipe, is equivalent to 6 m of water. If the pressure head at the throat is zero, calculate the throat diameter of the venturi.Include fbd.
Water flows through a horizontal Venturi meter whose inlet diameter is 33 cm. and throat diameter is 21 cm. The pressure at the inlet is 770 kPa and at the throat is 585 kPa. Determine the discharge in L/s. Neglect head lost. Only accepted answer is 728.658. Show solution.
Water in a partially filled large tank is to be supplied to the rooftop, which is 8 m above the water level inthe tank, through a 2.5 cm internal diameter pipe by maintaining a constant air pressure of 300 kPa (gauge) inthe tank. If the head loss in the piping system is 2 m of water, determine the discharge rate of the supply ofwater to the rooftop in L/s. Show complete solution
A 100m long pipe with diameter D = 20cm and CH/w= 120 carries a discharge of 30lit/sec. Determine the head loss in the pipe.
At the end of the summer, a swimming pool is being drained through a very long,small-diameter hose. The hose is smooth, of inner diameter D = 6.0 cm,and of length L = 65 m. The initial height difference from the pool surface to theoutlet of the hose is H = 2.20 m. Calculate the volume flow rate in litres per minute(LPM) at the start of draining.
Water at 20°C is withdrawn from a reservoir by means of a siphon, as shown in the figure. For d=10cm and D= 16cm, Determine: a) the minimum flow rate that can be achieved without cavitation occurring in the piping system, and b) the maximum elevation of the highest point in the piping system to prevent cavitation. c) Also, comment on the ways to increase the maximum elevation of the highest point in the piping system to prevent cavitation. (The saturation pressure of water at 20°C is 2.33 kPa)
A pump is required to move water at a design discharge of 1m3 /s between reservoirA to reservoir B (see schematic below). The difference in surface water elevations between A and B is10m. The difference in elevation between the surface elevation of A and the center of the first pipe sectionis 2m. The pipe is to be commercial steel with an internal diameter of 35cm. Determine the maximumdistance, LAP, from reservoir A that the pump could be installed without encountering cavitationproblems. Consider minor losses of a sharp-edged inlet. Assume a kinematic viscosity of 1x10-6 m 2/s and a specific weight of 9.79kN/m3 . Assume STP conditions (i.e., Pvapor = 3kPa, Patm=101.3kPa)
Two new cast-iron pipes (ε = 0.26 mm) in series connect two reservoirs. Both pipesare 300 m long and have diameters of 0.6 m and 0.4 m, respectively. There is a valvein the 0.6 m diameter line with K = 10. The elevation of water surface in reservoir A is80 m. The discharge of 10°C water from reservoir A to reservoir B is 0.5 m3/s. Find theelevation of the surface of reservoir B. Assume a sudden contraction at the junctionand the entrance and exit is sharp.