Q. No 3). A water supply pipe line is designed to supplying water to a nearby city. Determine velocity of water when it reach to a location 1.3 km from the pumping station where maximum head loss was found to be X m. Assume that pipe used is having diameter of Y cm and commercial steel pipe is used in the project. X= \.68 || 3

Q. No 3). A water supply pipe line is designed to supplying water to a nearby city. Determine velocity of water when it reach to a location 1.3 km from the pumping station where maximum head loss was found to be X m. Assume that pipe used is having diameter of Y cm and commercial steel pipe is used in the project. X= \.68 || 3

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

reservoir with water pressurized pipe diameter is 5 cm. The head loss in the system as given by hL= 5V^ 2/ 2g. The height between the water surface and the pipe outlet is 400 m. A discharge of 0.11 m3 /s is needed. What must the pressure in the tank be achieve such a flow rate? Assume a turbulent flow.
Suppose the pump of Fig. P14–23 is operating atfree delivery conditions. The pipe, both upstream and downstreamof the pump, has an inner diameter of 2.0 cm andnearly zero roughness. The minor loss coefficient associatedwith the sharp inlet is 0.50, each valve has a minor loss coefficientof 2.4, and each of the three elbows has a minor losscoefficient of 0.90. The contraction at the exit reduces thediameter by a factor of 0.60 (60% of the pipe diameter), andthe minor loss coefficient of the contraction is 0.15. Note thatthis minor loss coefficient is based on the average exit velocity,not the average velocity through the pipe itself. The total length of pipe is 6.7 m, and the elevation difference is (z1 - z2)= 4.6 m. Estimate the volume flow rate through this pipingsystem. Complete Answer, Thank you
choose the correct answer Q1A- Using water jet forces to operate turbines in hydropower plant consider application of: * a) Bernoulli’s equation b) Darcy-Weisbach Equation c) Manning equation d) Momentum equation E-none of all above B-The main difference between the flow in pipes and the flow in open channels is * a) Existing the head loss b) Existing the free surface c) Existing the pressure drop d) None of all above
A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m. the total length and diameter of the sunction and discharge pipe are 500 mm,1500 m and 300 mm, 1000 m respectively. assumme a head lose of 2 meters per 100 m length of the sunction pipe and 3m per 100 m length of the discharge pipe. what is the required horsepower of the pump?
The following system is fed by a centrifugal pump. The piping is constructed from smooth plastic of OD 55 mm, wall thickness 2.5 mm. The minor losses for the system prior to the pump are given by KL = 12.0. The system curves for this pump are attached. If the flowrate is reduced to 1.4 m3/hr, and the upstream head requirement were 17 m, what would the electrical power requirement of the pump be?
A pump is being utilized to deliver a flow rate of 500 li/sec from a reservoir of surface elevation of 65 m to another reservoir of surface elevation 95 m.The total length and diameter of the suction and discharge pipes are 500 mm, 1500 m and 30 mm, 1000 m respectively. Assume a head lose of 2 meters per 100 m length of the suction pipe and 3 m per 100 m length of the discharge pipe. What is the required horsepower of the pump? **provide complete solution using bernoullis equation..provide illustration with labels like datum line and such** Show all formula derivation
The head-versus-flow-rate characteristics of a centrifugalpump are shown in Fig.. If this pump drives water at20°C through 120 m of 30-cm-diameter cast iron pipe,what will be the resulting flow rate, in m3/s?
Water at 16,2°C is to be discharged from a reservoir at a rate of 16,2 L/s using two horizontal cast iron (roughness value ɛ=0.00026m) pipes connected in series and a pump between them. The first pipe is 26,2 m long and has a 66,2 mm diameter, while the second pipe is 36,2 m long and has a 46,2 mm diameter. The water level in the reservoir is 30 m above the centerline of the pipe. The pipe entrance is sharp-edged (KL=0.562), and losses associated with the connection of the pump are negligible. Neglecting the effect of the kinetic energy correction factor, determine the required pumping head, the minimum pumping power and electric motor power for total efficiency value of 76,2% to maintain the indicated flow rate. Water density is r=996,2 kg/m3, dynamic viscosity µ= 1.162x10-3kg/ms. Solve the problem by making the necessary assumptions and drawing the schematic figure.
Water is pumped between two reservoirs in a pipeline with the following characteristics; (d= 300mm, L= 70m, /= 0.025, minor loss coefficient: YK=2.5). The pump performance curve is approximated by the equation: H,=22.9-650° Where H, is in meters and Q is in m's. Determine the discharge Q and pump head A when two pumps in series are used for total static head (4Z=25m).
In a 225 mm pipeline 0.14 m3/s of water are pumped from a reservoir of surface elevation30 over a hill of elevation 50. A pump of what power is required to maintain a pressure of 345kPa on the hilltop if the head lost between reservoir and hilltop is 6 m?
Calculate the power required to pump water at 120 kg/s from a supply tank, through an 18 cm diameter galvanised iron pipe to a storage tank located 12m above the supply tank. The length of the pipe is 70 m. All losses other than friction losses are ignored. [Hint: Use Moody Diagram] (For water, ρ = 1000 kg/m3, μ = 1.003 x 10-3 Pa.s)
A pumping system has the following characteristics, f=0.015 length of thepipe = (2500 ft) pipe diameter 6 in, losses less than 0.5, the pipeis cast iron, and the system curve is:Hp= 34+ 5.47Q2Knowing that the system curve and the pump curve intersect at 12 cfsa. Determine Operation headb. Determine dischargec. Plot the system curve