we will calculate with numerical values. Tar the thermal circuit for heat transfer via the composite block (depth W) from left insulation to the right into the atmosphere. Block B's surface has an emissivity of ε = 0.4 and is also exposed to convection. Other known parameters are: LA=0.2 m, LB=0.4 m, H = W=1 m, k = 2 W/mK, kB = 3 W/m-K, T₁ = 50°C, T₂ = 42°C, and To Tsurr 25°C. What must be the value of the convection coefficient (h)? [Hint: Thermal circuit is analogous to electrical circuits. Also remember, Kirchhoff's Current & Voltage Law (KCL & KVL) will apply in thermal circuits.] h. Too

we will calculate with numerical values. Tar the thermal circuit for heat transfer via the composite block (depth W) from left insulation to the right into the atmosphere. Block B's surface has an emissivity of ε = 0.4 and is also exposed to convection. Other known parameters are: LA=0.2 m, LB=0.4 m, H = W=1 m, k = 2 W/mK, kB = 3 W/m-K, T₁ = 50°C, T₂ = 42°C, and To Tsurr 25°C. What must be the value of the convection coefficient (h)? [Hint: Thermal circuit is analogous to electrical circuits. Also remember, Kirchhoff's Current & Voltage Law (KCL & KVL) will apply in thermal circuits.] h. Too

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Recall that power available at altitude is (rho/rho0)*power at sea level. Include transmission losses! [~, a, ~, RHO, ~] = atmosisa(alt(k1)*0.3048); rho=RHO*0.0685218/35.3147; rho_scale=rho/rho0; a=a/0.3048;
30_ Select the correct statement for a radial conductivity exp Select one: a. The mid outer surface represent the heating area while the side surface represent the cooling area b. None of them is true c. The outer section represent the heating area and the inner section represent the cooling area d. The inner section represent the heating area and the outer section represent the cooling area 24_ The device with highest static head loss is Select one: a. No static head loss in this experiment b. Venturi meter c. Orifice plan d. Rotameter 26_ If surface is not leveled under the center of pressure tank Select one: a. Legs of the device can be rotated to create level surface b. Items should be added under the device to create level surface c. The device has and auto leveling d. none
A thermocouple produces an emf in mV according to the temperature difference between the temperature at the sensor tip and the temperature at the gauge. Given, α = 3.5x10-2 mV/°C β = 8.2x10-6 mV/°C Determine the mV output when the tip is 220°C and the gauge head at 20°C.
ANS : Q=114.93W/m
5.The value of a resistance is 4.7kN while measurements yields a value of 4.63kn.Calculte (i)Absolute accuracy (ii)Percentage of Accuracy.
QUESTION 3Discuss the five characteristics of a System.
A chromel-constantan type thermocouple has a cold junction (or cold terminal) at the temperature of 20ºC. The tables provide the following values for this thermocouple: 0°C for e.m.f = 0.000 mV; 20ºC for e.m.f = 1192 mV and 200ºC for e.m.f = 13419 mV. To determine:(a) The Seebeck coefficient (or proportionality constant) of this thermocouple. (b) The electrical voltage at the thermocouple terminals when the hot junction (or terminal hot) is at a temperature of 200ºC.
5. 30,000 kW at power factor 0-8 lagging is being transmitted over a 220 kV, three-phase transmission line. The length of the line is 275 km and the efficiency of transmission is 90%. Calculate the weight of copper. Also calculate the weight of copper had the power been transmitted over a single-phase transmission line tor the same line voltage and losses. ASsume that the resistance of 1km long conductor and 1sq.cm is 0.173 andspecific gravity of copper is 8-9.
Consider a Wheatstone bridge circuit that has all resistances equal to 100 Ω. The resistance R1 is a strain gauge that cannot sustain a power dissipa- tion of more than 0.25 W. What is the maximum applied voltage that can be used for this bridge circuit? At this level of bridge excitation, what is the bridge sensitivity?
Measurement & metrology thermometer reads 97.2 C and the static correction given in the correction cu is-0.06 °C. Determine the true value of the temperature.
Give definition of unreliability F(t)of a component as function of time.
A pressure measurement system is stated as having the followingcharacteristics. Explain the significance of the terms:Range: 0 to 125 kPa and 0 to 2500 kPaAccuracy: ±1% of the displayed readingTemperature sensitivity: ±1% of the reading per o C