what is the component that is moving to allow fuel to be injected into the intake port

Q: What test can be performed to check the efficiency of individual cylinders?

A: Given Data : Individual cylinder Efficiency

Q: C.Both A and B

A: The main objective of Central port fuel injection system is to a low cost multi point fuel injection…

Q: Differentiate the two types of external combustion engine

A: There are two types of external combustion engines. (1) Steam engines (2) Stirling engines

Q: ne fluid power system

A: Pnuematic.

Q: Unburned HC and Carbon mono-oxide reduced in the exhaust gases if the A/F decreased True False

A: Unburned HC and Carbon mono-oxide reduced in the exhaust gases if the A/F decreased True False

Q: Technician A says that black exhaust smoke is an indication of a too-rich air-fuel mixture.…

A: Air–fuel ratio is defined as the mass ratio of air to fuel present during combustion. Rich air-fuel…

Q: Carbon deposits on the intake valve or seat may cause the valve not to close properly. Tech a says…

A: If carbon deposits form on the valves or valve seats, the valves will be unable to close properly.…

Q: Explain the operation of the internal combustion engines (ICEs) valve system.

A:

Q: What precaution should you take to prevent hydraulic injection?

A: Some precautions to be taken to avoid hydraulic injection are, When the hoses or hydraulics are…

Q: Choose the correct statement. Select one: a. A dry sump system stores oil in a tank outside of the…

A: The wet sump system  is the best fit during aggressive driving conditions.

Q: 1: List the safety mechanisms that contrast medium injection devices are equipped with.   2: What…

A: 1. Safety mechanisms that contrast medium injection devices are equipped with- The function…

Q: 1 Before conducting a __________ test, disable the ignition and the __________ injection system.…

A: Compression test Compression test is the test for the engine to check the condition of the parts of…

Q: In an IC engine the inlet valve diameter will be bigger than the outlet valve ? Select one: O True…

A:

Q: What is the name of the component that opens the valves?

A: There is a special component on the valve which is used to open the value.

Q: Decribe different types of jet from orifice.

A: Orifice: Orifice is a small opening of any cross cross sections such as circular , rectangular on…

Q: identify the different components of the ICEs valve system.

A: The components of IC engine valve system are - Valve guide Valve stem Valve spring Cam and follower

Q: Technician A says that the engine oil drain plug typically needs to be replaced with a new one at…

A: At every maintenance trip of the automobile engine oil is changed by removing the oil drain plug.

Q: The following vehicle does not have an injection system

A: Answer 1  Explanation  The internal combustion engine have the injection system because I C engine…

Q: Technician A says that all transmission opening pressure are derived from the regulated output flow…

A: Technician A says that all transmission opening pressure are derived from the regulated output flow…

Q: An engine starts and runs briefly after a small quantity of fuel is put into the spark plug hole,…

A: An engine starts and runs briefly after a small quantity of fuel is put into the spark plug hole,…

Q: Coolant leaking into the combustion chamber produces what color smoke from the exhaust? Select one:…

A: We have to know

Q: Technician A says it is important to note transmission fluid temperature when checking the fluid…

A: For level checking of transmission fluid its temperature is checked. Transaxle has fluid for…

Q: Technician A states that coolant in a normal flow cooling system flows from the radiator to the…

A: Answer: a) Technician B only

Q: the 2 separate

A:

Q: Which one of the following is a component of a centrifugal compressor? a. Suction valve b. Nozzle…

A: Although the centrifugal compressor is unlikely to be used in gas turbine plants where specific fuel…

Q: What is the method by which the pressure of the air entering the engine is raised using a compressor…

A:

Q: what type of radiator pressure cap is found on today's vehicle

A: Solution:

Q: 13. One of the advantages of force-duct with exhaust overlap system is it provides cool air to the…

A: Since you are posted multiple questions, we have to answer only first question. Kindly Post the…

Q: How many degrees the crankshaft will rotate with both the intake and exhaust valves seated when the…

A: Calculate the degrees for which the crankshaft rotates with the intake and exhaust valve seated.…

Q: Excessive oxygen in the exhaust indicates an improper air/fuel mixture.

A: Excess oxygen in the exhaust demonstrates an inability to accomplish that objective and is for the…

Q: Which type of oil filter uses an anti drain back valve to prevent it from emptying of oil when the…

A: Which type of oil filter uses an anti drain back valve to prevent if form emptying of oil when…

Q: Which of the following is not true about the cylinder lubrication of 2-stroke crosshead diesel…

A: A two-stroke IC engine completes the power cycle with two strokes of the piston during one…

Q: List the main components of the internal combustion engine.

A: Internal Combustion Engine: Internal combustion engine mainly known as IC Engine. In this kind of…

Q: What would happen if one of the Flow Controls were reversed in a cylinder?  What are the…

A: Consider the cylinder as an open system. To implement the flow controls, consider the control volume…

Q: What is the advantage of a variable intake system and what inputs are required by the ECM?

A: The variable intake system is an advance manifold technology incorporated in an internal combustion…

Q: 1- What is “valve overlap” and how it's affect the performance of the engine

A: Time period for which both exhaust valve and intake valve remain open at the same time during…

Q: INTRODUCTION ABOUT VALVE SYSTEM IN INTERNAL COMBUSTION ENGINE

A: In this solution we will only discuss about the brief introduction about the valve mechanism in the…

Q: cpi (Central Multiport injection) injectors are located in the lower half of the intake manifold. T…

A: CPI (Central Multiport Injection) injectors are located in the lower half of the intake manifold.

Q: The fuel temperature is measured in the low pressure part of the fuel system just before the fuel…

A: To choose: The correct option for the problem. Explanation: Fuel must be transported from the fuel…

Q: How does resurfacing the cylinder head of an ohc engine affect valve timing and what should be done…

A: Cylinder head resurfacing removes some layer of material to provide clean flat surface for placing…

Q: explain the purpose of the relief valve and one way check valve in an electric fuel pump.

A: The Relief valves are basically used to control the pressure in a system. One-way check valve allows…

Q: When installing a spin-on oil filter, failure to lube the O-ring will:

A: The correct option is a.

Q: If the oil on the dipstick looks milky gray, it is possible that there is water (or coolant) being…

A: Solution:

Q: What is the temperature of the cylinder whe

A: Need To calculate the temperature of cylinder.

Q: What is the purpose of blowing the Main Engine (kick start by air) before initial start up? * To…

A: Disclaimer: Since you have posted multiple questions we will solve the first question for you. If…

Q: is it true that an l head engine has the intake and exhaust valves mounted in the cylinder head

A: Solution:

Q: Amount of fuel consumed by the engine for each horsepower or pound of thrust Fuel Consumption Weight…

A: Now defined each term as follows. Fuel consumption weight is defined as fuel consumed by the engine…

Q: F. What is the compression ratio?

A: Given:   T3= 2500 deg F. T4= 886 deg F To find : Compression ratio

Q: The intake process wherein the pressure of the air entering the engine is increased by means of…

A: The objective of a turbocharger is to improve an engine's volumetric efficiency by increasing the…