What is the correct procedure for making a stock solution after you have weighed the necessary amount of solute. O Add the solute to the volumetric flask, add solvent to just below the neck of the volumetric flask, invert the volumetric flask until the solute is dissolved, and then fill volumetric flask to the mark O Add solvent to the volumetric flask to just below the neck, add the solute to the volumetric flask, invert the volumetric flask until the solute has dissolved, fill the volumetric flask with solvent up to the mark O Add the solute to the volumetric flask, fill the volumetric flask with solvent up to the mark, invert volumetric flask until the solute has dissolved

What is the correct procedure for making a stock solution after you have weighed the necessary amount of solute. O Add the solute to the volumetric flask, add solvent to just below the neck of the volumetric flask, invert the volumetric flask until the solute is dissolved, and then fill volumetric flask to the mark O Add solvent to the volumetric flask to just below the neck, add the solute to the volumetric flask, invert the volumetric flask until the solute has dissolved, fill the volumetric flask with solvent up to the mark O Add the solute to the volumetric flask, fill the volumetric flask with solvent up to the mark, invert volumetric flask until the solute has dissolved

EBK A SMALL SCALE APPROACH TO ORGANIC L

4th Edition

ISBN:9781305446021

Author:Lampman

Publisher:Lampman

Chapter79: Solubility

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

How do we keep relative supersaturation low by controlling solute concentration? concentration should be constant concentration should be higher concentration should be lower concentration should be fluctuating
Pre Lab Questions: (Each answer is to be written as a complete sentence) What is the reason for washing the precipitate with water in Step 9? Define precipitate. Define filtrate. In Step 2, what is the purpose for rinsing the stirring rod? read the Procedure to answer the questions Using a balance, mass between 1.50 – 2.00 grams of sodium carbonate in a pre-massed 150mL beaker. Add 20 mL of distilled water and stir thoroughly to make sure all the crystals are dissolved. Rinse the stirring rod with a little distilled water after stirring. Using a balance, mass between 1.50 – 2.00 grams of calcium chloride dihydrate in a pre-massed 50 mL beaker. Repeat Step 2 for the solution in the 50 mL beaker. Pour the calcium chloride solution into the 150mL beaker containing the sodium carbonate solution and stir. Mass a piece of filter paper. Fold the filter paper and place it into the funnel. Wet it with a little distilled water to ensure that it is stuck to the sides of the funnel. Slowly…
In an alternate procedure, a 0.50 M nickel (II) nitrate solution was used to prepare the standard solutions for a Beer’s Law plot. If a 10.0 mL volumetric flask is used to prepare the dilution, what volume of 0.50 M nickel (II) nitrate is needed to prepare a 0.15 M standard solution? Show all of your work
Table 1: Temp vs. solubility data of ammonium chloride. Test tube g NH4Cl/10 mL H2O Crystallization temp. (ºC) 1 1.0 g/10 mL H2O 10 oC 2 1.8 g/10 mL H2O 20 oC 3 2.9 g/10 mL H2O 40 oC 4 3.8 g/10 mL H2O 65 oC 5 4.4 g/10 mL H2O 95 oC Use the table to plot a solubility curve for ammonium chloride on the graph provided below. For the best fit line, use a smooth curve. "Mass of Solute per 100 mL of H2O," should be written on the y-axis (use increments of 2g for every box). "Temperature (°C)" should be written on the x-axis (use increments of 10 °C for every 2 boxes).
Which of the following is true when preparing solutions? a. Make sure that the solvent and reagents are contaminated. b. When diluting to the mark using a volumetric flask, the upper meniscus and mark should be at eye level. c. If amount added is over the mark, you cannot just take out the excess liquid and preparation must be repeated. d. After mixing the contents of the flask and the level of the meniscus seems lower than the mark, add more diluent.
A student, performing the same experiment as you, recorded the following information. The original solution was diluted by a factor of 5.Calculate the volume of NaOH used to reach the equivalence point. Volume of diluted vinegar sample (mL) 25.00 Molarity of NaOH 0.0900 Initial buret reading (mL) 16.50 Final buret reading (mL) 38.00 Volume of NaOH
The first goal is to make the oxalic acid standard solution. You measure 1.5232 g of oxalic acid on an analytical balance, add it to a 250-mL volumetric flask and add deionized H2O to a final volume of 250.0 mL. Molar mass of H2C2O4•2H2O = 126.07 g/mol Mass of H2C2O4•2H2O = 1.5232g what is the Number of moles of H2C2O4•2H2O?
Consider the following scenario: After the first compound elutes off of the column, you collect multiple fractions without seeing the next compound begin to elute. What change might you want to make before you continue taking fractions?
Preparation of Ascorbic Acid Stock Solution and Dilution. Problem: Determine the amount of 500 mg ascorbic acid tablets needed to perform the experiment. Concentration of stock solution: Stock Solution = 6%m/v Dilute to = 5.4% New Volume = 75 mL Please provide complete solutions.
States of Matter Applying like dissolves like For each solute, click the button under the better solvent. Solute I need expert solutions please
What is the final molarity of sodium thiosulfate pentahydrate for each of the runs? Given: the initial volume of each component was diluted to 100mL mass of sodium thiosulfate pentahydrate used: 0.115g 0.0025 M sodium thiosulfate pentahydrate run #1: 10mL run #2: 10mL run #3: 10 mL
How to prepare Saturated brine (NaCl) solution (50 mL)