What is the flat to flat width of the bolt head

Q: The wrong maintenance procedure followed while performing gib adjustment on a lathe machine is O…

A: The correct maintenance procedure for gib adjustment on the lathe machine Adjust the gib to new…

Q: cker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in inches

A: A four-bar crank-rocker mechanism rocking angle of 70 degrees. What are the lengths of the 4 bars in…

Q: what is the minnimum proof strength mpa for M14x2 hex bolt

A:

Q: Why must a cylinder ridge be removed before attempting to remove the piston?

A: Cylinder ridge reamer is a component use to remove the ridge.

Q: Which of the following is the most common method of snug tightening bolts? O Heat tightening O…

A:

Q: -rce. What is the best angle?

A: To find angle.

Q: List down the safety precaution need to carry during the operation of drilling?

A:

Q: Give the true thread from the following, the reasons for the false. representation of screw and mark

A: Given Screw thread To find Determination of the proper screw thread representation   Screw thread…

Q: What is the total length of Tailstock ?

A:

Q: What tool is generally used to measure crank shaft bearing journals? a. vernier calipers b.…

A: The dial bore gauge measures the inside diameter of the round holes of crankshaft journal bearings.

Q: Chrome-molybdenum b) Aluminium alloy c) Douglas fir d) Mild steel

A:

Q: Question 17? Approximately how many threads are specified for the bolt?

A:

Q: What ares name of the tools equipment

A:

Q: Do not use _____ on nuts and bolts unless someone has rounded off edges of the nut or bolt.

A: Solution:

Q: How are single-acting cylinders retracted?

A: To find : How are single-acting cylinders retracted?

Q: the minimum metric specification required for the bolt is

A: Given, Determine the minimum metric specification required for the bolt ? where, Figure shown three…

Q: What is the width of the groove on the bolt?

A: Given :- Bolt drawing Find :-  Width of the groove on the drawing = ?

Q: Industrial Main   What is the first step to installing a bearing on a shaft

A:

Q: Define the Crowned Nut and where is it used? Please define the shoulder nut and where is it used

A: Crown-Nuts. An Embed for utilization inside the end of the circular and square area. The Crown-nut…

Q: What is a moment of intertia?

A: When an amount of force applied perpendicular to any object then the tendency of that force to…

Q: Describe the automatic hammer with diagram.

A: Hammers are used in many industrial areas. While going with the conventional hammering method it…

Q: Advantage of taper turning by  tail stock  set over method  is that power feed can be used. Select…

A: Let us discuss about tailstock offset method.

Q: Draw a sectional front view, top view and side view for Hexagonal bolt (M d mm *L mm)?

A: Given Hexagonal Bolt To find Sectional front view Sectional top view Sectional side view

Q: (a) Why the connecting rod is made as I section? Why do some connecting rods have hole drilled from…

A: The connecting rod is a mechanical component that connects the engine's piston and crankshaft. In…

Q: I how such a bolt most likely to fail, will it fail ir

A:

Q: the bolt is

A:

Q: What is the Axial Load?

A: The axial load is a force that acts along the centroidal or longitudinal axis of the system. If the…

Q: 5 inch dia. shafts coupling to connect the equipment shafts. Note: use 4 bolts only nstructions:

A:

Q: -.3: Draw the front view for a square-headed bolt and a square neck with a castle nut and a washer…

A: Given data: The diameter of the bolt is D = 24 mm. The length of the bolt is L = 100 mm. Here, the…

Q: which best manufaring process use to manufacture carbon steel segment gear?

A: There are so many processes to manufacture segment gear. These are given as, (1) Casting: Sand…

Q: bolts required for an

A:

Q: Technician A says a bolt may become fatigued if it is over tightened. Technician B says that a bolt…

A: The bolt will be fatigued in both the overtighten and under-tightening cases

Q: 6lb hammer of a pile driver is lifterd 5m the pilling head. If the hammer is released, what will be…

A:

Q: List the steps that should be followed to preciselytighten a bolt to specifications.

A: Common fasteners that join two or more pieces of work together include nuts and bolts. You will need…

Q: What type of Bolt is the following image?

A: According to the figure, Flange Bolt is showing in the above picture.

Q: Why should you not hold work by hand when drilling? What are the safety measures one must take…

A: Solution:   Drilling is a manufacturing process to form a hole in a workpiece.

Q: Explain the Automatic hammer: basic components and operation.

A: An automatic hammer used to find the standard penetration test counts for geotechnical projects. The…

Q: Which of the following arrangements is least effective in tightening the nut? rod wrench wrench nut…

A: The Force acting in each case is F. The amount of torque produced by the force F depends upon the…

Q: What size of hole must be drilled in an M 42 bolt to make the bolt of uniform strength

A:

Q: a bolt pattern in shear, if the line-of-action of the load passes through the centroid of the bolt…

A:

Q: Which of the following wrenches is the best choice fortorquing a bolt?a. Open-endb. Box-endc.…

A: When it comes to bolted joints, orquing is the most popular method of achieving fastener preload.…

Q: *Single rod cylinder should be double acting cylinder True O False O

A: It is false that single rod cylinder should be double acting cylinder.

Q: What is the depth, minor diameter, width of crest and root for a bolt 1⁄2 X 20 UNF

A: UNF = Unified National Fine Screw Thread.   The Nominal Major Diameter and Threads-per-inch (Pitch)…

Q: In general: Abrassive blasting _____ be used for deburring. Abrassive blasting _____ be used for…

A: Abrasive blasting- Abrasive blasting is generally known as sandblasting. It is the operation of…

Q: What is the overall height of Tailstock?

A: To Find the overall height of Tailstock?

Q: Which type of bands are used for cutting many types of steel?     a)Alternate set b)The standard…

A: Hook tooth blades are able to take deep bits out of the material. They are used mostly for hardwood…