What is the height difference reading on the U-Tube? *4, contraction.Consider a low speed subronic wind tunnel with aarea ratio for the nozzle. If the flow in the test section is at avelocity of 30 meters per vec,standard seo level conditions with aCalculate the height difference in a U-tube mercury manometer n ithone side connected to the nozzle inlet and the other to the tertK9/m3section. Pig = 1.36 x100.05 m0.39 m0.34 m0.22 m0.11 m0.21 mO

Answered: Image /qna-images/answer/7e0ace64-3f76-4d65-8f2b-4cbec20c68ef.jpg

What is the height difference reading on the U-Tube? * 1. Consider a low speed subronic wind tunnel with a contraction. area ratio for the nozzle . If the flow in the testsection is at a stondard seo level conditions witha velocity of 30 meters per vec, Calculate the height difference in a U-tube mercury manometer w ith one side connected to the nozzle inlet and the other to the test 3 k9/m3 section. Pg = 1,36 x10 0.05 m 0.39 m 0.34 m 0.22 m 0.11 m 0.21 m

What is the height difference reading on the U-Tube? * 1. Consider a low speed subronic wind tunnel with a contraction. area ratio for the nozzle . If the flow in the testsection is at a stondard seo level conditions witha velocity of 30 meters per vec, Calculate the height difference in a U-tube mercury manometer w ith one side connected to the nozzle inlet and the other to the test 3 k9/m3 section. Pg = 1,36 x10 0.05 m 0.39 m 0.34 m 0.22 m 0.11 m 0.21 m

University Physics Volume 1

18th Edition

ISBN:9781938168277

Author:William Moebs, Samuel J. Ling, Jeff Sanny

Publisher:William Moebs, Samuel J. Ling, Jeff Sanny

Chapter14: Fluid Mechanics

Section: Chapter Questions

Problem 34CQ: The old rubber boot below has leaks. To what maximum height can water squirt from Leak 1? How does...

See similar textbooks

Similar questions

A submarine dives at 9.1m/s, at an angle of 15° to the surface of the water (i.e. downwards). Taking sea water density to be constant at 1002kg m^-3, what is the rate of change of pressure with time (Pa s^-1)?
If the atmospheric pressure is 1,051 mm Hg and the height difference between the two arms is 14.4 cm , what is the pressure of the gas sample below in atmospheres (atm)?
An important design consideration in two-phase pipe flow of solid-liquid mixtures is the terminal settling velocity below, which the flow becomes unstable and eventually the pipe becomes clogged. On the basis of extended transportation tests, the terminal settling velocity of a solid particle in the rest water given by VL = FL√2gD(S − 1), where FL is an experimental coefficient, g the gravitational acceleration, D the pipe diameter, and S the specific gravity of solid particle. What is the dimension of FL? Is this equation dimensionally homogeneous?
Consider the sealed containers (same fluid and on the same ground level) below with heights given in a and b values.Provided that b = 2a, answer the following items. If a = 2 in, and the density of the fluid is 60 lbm/ft^3, what is the pressure at point B in psia?
What is the ratio of the average distances that oxygen willdiffuse in a given time in air and water? Why is this distanceless in water (equivalently, why is D less in water)?
Water flows through the spillway of the dam as shown in the figure. between point (1) and point (2) Ignoring the loss and assuming the unit width, the width is the difference between the average flow velocity V1 at point (1) and point (2). What is the average flow velocity V2, respectively?
Using the data as shown for the venules, and assuminga typical blood flow rate of 5.0 L per minute,a. What is the flow speed in the venules?b. What is the pressure difference across a 1.0 cm length of venule?
By considering the convex meniscus of mercury of density, ( in a capillary glass tube of radius, r deduce with explanation and equations that the height , d is given by where other symbols have their usual meanings. What is the significance of the minus sign
Calculate the pressure due to the ocean at the bottom ofthe Marianas Trench near the Philippines, given its depth is11.0 km and assuming the density of sea water is constantall the way down. (b) Calculate the percent decrease involume of sea water due to such a pressure, assuming itsbulk modulus is the same as water and is constant. (c) Whatwould be the percent increase in its density? Is theassumption of constant density valid? Will the actual pressurebe greater or smaller than that calculated under thisassumption?
Each second, 0.07 m^3 of water flows through a firehose. If the water is to leave the nozzleat a speed of 25 m/s, what should its diameter be?
Why is flow separation in flow over cylinders delayed when the boundary layer is turbulent?
The pressure difference between an oil tube and a water tube is measured with a dual fluid manometer, as shown in the figure. For specific heights and gravities given of the fluids. Calculate (PB - PA)