What is the horizontal and vertical components of the force of the pin at C (kN)? EGF6 kN2 m1 mBA-2 m--1 m→|Each member of this frame are connected with pin joints. The weight of each member is negligible.

Answered: Image /qna-images/answer/84c391e1-6950-4192-8d18-fd0dacd10731.jpg

Answered: What is the horizontal and vertical…

Engineering

Mechanical Engineering

What is the horizontal and vertical components of the force of the pin at C (kN)?

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.55P: Solve Prob. 10.54 assuming that A and B are connected by a spring of stiffness k = 0.3 W/b and free...

See similar textbooks

Related questions

Q: Determine the nature and magnitude of forces in the members 1,2 and 3 using section method.

A: The free body diagram of the truss is as follows:

Q: Calculate the magnitude of the force acting on the pin at D. Pin C is fixed in DE and bears against…

A: Mechanical Equilibrium: A body is said to be in mechanical equilibrium if it satisfies the following…

Q: Q3/. The portable floor crane in the automotive shop is lifting a 420 lb engine. For the position…

Q: The portable floor crane in the automotive shop is lifting a 530-lb engine. For the position shown…

A: Find force at support C and pressure in piston Load =530 lb

Q: As per the crane shown in the Figure. Determine the force member at AC, BC, BD, CD, CE.

Q: The Dumpster D of the truck, which has a weight of 4,200 lb and a center of gravity at G is…

A: Given :- weight of the truce , w = 42 00 Lb

Q: A tensile force of magnitude a N is desired to be created on the cable AB.

Q: Q3/. The portable floor crane in the automotive shop is lifting a 420 lb engine. For the position…

A: Given: The load is 420 lb. Diameter of the piston is 3.2 in.

Q: Determine graphically the forces FAB and FAC

Q: draw the free body diagrams

A: Detailed solution is below attached file... Refer through it ... Any queries feel free to…

Q: draw free body diagrams for each

A: Free body diagram A free-body diagram shows the forces acted upon the body. It is a special example…

Q: Draw the free-body diagram of the entire assembly and member ABCD.

A: FBD entire assembly. (θ=0°) For euilibrium,∑MA=0Bx×8=P×20Bx=5P2∑FX=0AX=-BX=-5P2∑FY=0BY=P

Q: Determine the MAGNITUDE (absolute value) of the horizontal component of the reaction force at the…

Q: olve for the internal force in members CA, CB,

A: Given data given truss system

Q: Given the image below, what is the magnitude of the tension at J?

A: Given: Intensity of the uniformly varying force at 0.6 m distance from the z axis: →w=100 N/m Length…

Q: PROBLEMS - Two forces are applied at the end of a screw eye 30 500 N in order to remove the post.…

A: Mechanical Equilibrium: A body is said to be in mechanical equilibrium if it satisfies the following…

Q: Draw the FBD and derive the EOM of the pulley system below with respect to x using Ne

Q: For the bar used on a squat rack, similar to the one shown below, determine how much weight can be…

A: Given problem: To find the weight to be added to one side of the squat bar so that the bar begins to…

Q: The A-frame is being hoisted into an upright position by the vertical force of 62 lb . (Figure 1)

A: Given data as per the question The magnitude of force F =62 lb finding the position vector along AC…

Q: Please help me identify the zero force members in this truss.

Q: Draw the free-body diagram of block B. (You must provide an answer before moving on to the next…

Q: the force (in kN) in the member SR is

A: Given; Figure shows the truss, where, the load and the length of the bar is shownDetermine the…

Q: Q2/Draw the free body diagram (F.B.D) of the rigid system shown in fig. (2)

A: Free body diagram is the diagram that shows all the forces acting on the system.

Q: As in your role as a student in the functional physics course, you are required to determine the…

A: Draw the free-body diagram of the forces acting on joint A as shown below. Calculate the angle made…

Q: Entire frame, pulleys, and contacting cable to be isolated as a single unit. B L

Q: Determine the forces acting on the frame. Draw the free-body diagram of each of the members showing…

Q: What is the normal force between the crate and the wedge? What is the smallest force P needed to…

Q: e if the members are in tensic pport forces and force in eac e if the members are in tensic D

Q: Q4/ Calculate the magnitude of the force supported by the pin B and roller support A for the bell…

A: Given: The magnitude of the force is F=220 N. The magnitude of the couple is M=50 N·m. Draw the…

Q: Calculate the reaction force at support B Calculate the reaction force at support B when the support…

A: Given: A propped cantilever beam as shown in Fig w= 7kN/m P= 14kN flexural rigidity (EI)= 4 MN.m2…

Q: Determine the forces at the contact surfaces A, B and C. Assume frictionless surfaces for all points…

Q: 1. What is the Vertical component (y-component) reaction force at support C? 2. What is the…

Q: The axial force at member AE is

Q: The force in member CD of the given truss

A: given truss as shown below

Q: Determine the bar force at FE and FN

A: Solution:

Q: Determine Reaction and Internal Member Forces

Q: nember of the loaded truss. The force

Q: = the tension forces for

A: To find Tension forces

Q: Determine the magnitude of the pin force at A.

Q: Draw a force diagram for the magazine on a magazine rack. Label the force vectors and use equality…

A: The force on the magazine in the above system is shown as:

Q: 3. Find the Foroe required to lift the 15 slug oylinder. Draw 3 Free Body Diagrams.

A: given:

Q: Q31. The portable floor crane in the automotive shop is lifting a 420 lb engine. For the position…

Q: Question-3 Find the magnitude and nature of the forces in all the members of the given truss.…

A: The figure below represents the forces acting on the members, In triangle HFG, θ3=tan-12 m3…

Q: Look at the truss below. Fill in the correct magnitude with sign for each tension force acting on…

Q: hey may you please help me here 1) Determine the magnitude of the horizontal and vertical…

Q: A tree feller cuts off large tree near the ground level and then continues to hoist the trunk. If…

A: mass=3tonne=3metric tonConsidering that the distances are in mmVertical Distance =180+1080=1.26m…

Q: Calculate the force on the bar CF.

A: If a force F is inclined at an angle θ with the horizontal, then the component of force along the…

Concept explainers

Free Body Diagram

The system of forces acting on a body tends to either rotate it or make the body undergo motion. In general, when an external agent exerts a force on a body, the body undergoes translational motion and rotational motion. The body has six degrees of freedom under the influence of that force. Here, three degrees of freedom are from the translational motion while the other three are from the rotation motion. However, sometimes the bodies are not allowed to undergo any motion and are fixed, under such conditions the body is said to be constrained.

Question

What is the horizontal and vertical components of the force of the pin at C (kN)?

E
G
F
6 kN
2 m
1 m
B
A
-2 m-
-1 m→|
Each member of this frame are connected with pin joints. The weight of each member is negligible.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The 65 kg tag is supported by cables AB and BC, as shown in the image, which have diameters of 1.5 mm and 2 mm, respectively. If the cables have a normal ultimate stress of ?u = 400 ???. Determine: a) The safety factor in cable AB b) The safety factor in cable BC Please add the free body diagram.
The frame is used to carry high-voltage wires. If b=600mm, α=30° and W=981 N, find the internal force in member HJ? (Draw free body diagram)
This structure is supported by a roller joint on the left and a pin joint on the top. Two loads, P have similar magnitudes of P = 650 N and the angle θ = 40°. The length L of both members is 1.5 m. The vertical load acts at the midpoint of the horizontal member. Solve for the reaction forces at the roller and pinned joints.
Determine the forces in each member using any method discussed in your theory of structures/mechanics. Using Software is not allowed. Show complete solution and tabulate your answers indicating whether it is compression or tension. Use Pn = 205 kN, Po = Zero
Three steel rods (E = 200 GPa) supports a 50 kNload P. Each of the rods AB and CD has a 300 mm2cross-sectional area and rod EF has a 600 mm2cross-sectional area.(a) State whether the structure isstatically determinate or indeterminate.Why?(b)Determine the force and thestress in each rod.(c) Determine the deformation of each rod.Note: The link BED is rigid, and BE = ED.
The 304 stainless steel post A is surrounded by a red brass C83400 tube B. Both rest on the rigid surface. If a force of 25 kN is applied to the rigid cap, determine the required diameter d of the steel post so that the load is shared equally between the post and tube. The elastic modulus for brass is 101 GPa and the elastic modulus for steel is 193 GPa
A35-kg disk rests on an inclined surface for which µs = 0.2. The disk is connected to a beamby pin connection at A and the link is supported by pin at B. The vertical load P is applied onthe link AB at a location as shown in Figure 3 (b) Determine the support reactions at pin A and B
Each of the two members is made from 6061-T6 aluminum and has a square cross section 1 in. * 1 in. They are pin connected at their ends and a jack is placed between them and opened until the force it exerts on each member is50 lb. Determine the greatest force P that can be applied to the center of the top member without causing either of the two members to yield. For the analysis neglect the axial force in each member. Assume the jack is rigid.
The truss above has concentrated loads as shown. The wind loads of 50 KN are perpendicular to the member AF. Solve for the forces acting on the members BE, DE, DG, FG by the method of joints. Show all solutions please don't skip. Thanks!
Method of joints: The truss pinned to the floor at D, and supported by a roller at point A is loaded as shown in Fig. T-06. Determine the force in member CG. (with explanation)
Determine the forces in members a) AB, b) AG, c) GF, d) BF, e) BC. PLS USE JOINT METHOD GIVEN: W1= 13 kips W2= 12 kips b°= 39 degree a°= 7 degree L1= 3 ft L2= 8 ft L3= 7 ft PLS SHOW COMPLETE SOLUTION, WRITE LEGIBLY AND ONLY ROUND OFF THE FINAL ANSWER IN FOUR DECIMAL PLACES, ANSWERS SHOULD BE IN THE ATTACH TABLE. PLS SHOW THE FREE BODY DIAGRAM ON EACH JOINTS AND IN THE ANSWER IDENTIFY IF IT IS A TENSION OR COMPRESSION. PLS USE THE GIVEN VALUES A B AND C ARE ALREADY SOLVED PLS SOLVE ALL OR THE OTHER LETTER LETTER d.) and e.)
Determine the forces in members a) AB, b) AG, c) GF, d) BF, e) BC. PLS USE JOINT METHOD GIVEN: W1= 13 kips W2= 12 kips b°= 39 degree a°= 7 degree L1= 3 ft L2= 8 ft L3= 7 ft PLS SHOW COMPLETE SOLUTION, WRITE LEGIBLY AND ONLY ROUND OFF THE FINAL ANSWER IN FOUR DECIMAL PLACES, ANSWERS SHOULD BE IN THE ATTACH TABLE. PLS SHOW THE FREE BODY DIAGRAM ON EACH JOINTS AND IN THE ANSWER IDENTIFY IF IT IS A TENSION OR COMPRESSION. PLS USE THE GIVEN VALUES I ALREADY KNOW THE A B AND C PLS SOLVE NOW D AND E AND THE ANSWER SHOULD BE IN THE ATTACHED TABLE